Toshiba IK-52N Manual de usuario

CCD CAMERA

IK-53N/IK-52N

OPERATING GUIDE

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must ac-

cept any interference received, including interference that may cause undesired operation.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own ex-

pense.

USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be

voided if you make changes or modifications not expressly approved by the party responsible for

compliance to Part 15 of the FCC rules.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.

CONTENTS

1. GENERAL ....................................................................................................................2

2. CAMERA PARTS AND FUNCTIONS ......................................................................... 3

3. CONNECTIONS ......................................................................................................... 5

4. SETTING .....................................................................................................................6

4-1. Field accumulation/Frame accumulation .........................................................6

4-2. Electronic Shutter ...............................................................................................7

4-3. Reset Restart ...................................................................................................... 8

4-4. External Trigger Mode........................................................................................9

5. Input Output Signal Specifications ....................................................................... 14

6. CCD Output Waveform Timing Chart ................................................................... 16

7. EXTERIOR VIEW ...................................................................................................... 18

8. SPECIFICATIONS ..................................................................................................... 19

1. GENERAL

The IK-53N/IK-52N is a monochrome video camera using a solid image sensor CCD (Charged

Coupled Device).

High Picture Quality

The 410,000 pixels CCD provides a fine picture.

Various Modes Setting

The following modes can be set by the switches on the rear panel.

• Gain: Fixed/manual adjustment (0 to +18 dB)

• Field accumulation/Frame accumulation

• Synchronized input/output (HD/VD)

• 75Ωterminal (at external synchronous input)

• Shutter function: Normal/external trigger shutter

• Shutter speed

External Synchronization

External HD/VD signals are analyzed and the synchronization mode is automatically selected

to match the input signals.

Internal Synchronizing Signal Output

HD and VD signals can be outputted from the 12-pin connector by changing the switch posi-

tion on the rear panel.

Electric Shutter Speed

A variety of shutter speeds (1/100 to 1/100,000 sec) is provided to permit choice suitable for

shooting conditions.

External Trigger Function

A trigger input provides one still image. This function exactly captures a subject moving at a

high speed.

Cabinet Fixing

The cabinet fixing screw hole is provided below the front panel which includes the CCD datum

level. Fix the camera using this screw hole to minimize shifts in the optical axis.

2. CAMERA PARTS AND FUNCTIONS

Top/Bottom/Front Side

[Top]

4[Bottom]

[Front]

Lens mount (C mount)

This is used to mount a C-mount type lens or

optical equipment.

Camera fixing reference hole (top side)

Camera fixing reference hole/Tripod fixing metal

screw hole (bottom side)

Camera fixing reference hole/Tripod fixing metal

screw hole (bottom side)

NOTE

When the mass of lens exceeds 300g, fix the cam-

era at the side of the lens.

Imaging area

The protection cap is attached on the lens mount

portion. After removing the cap, mount the lens.

Be careful not to scratch or touch the optical

area.

Rear Side

ON OFF

EXT INT

HD/VD

75Ω

SHT

TRG

M.G

MIN MAX

M GAIN

VIDEO OUT

DC IN/SYNC

FRM

Enlarged

VIDEO OUT DC IN/SYNC plug (12-pin connector)

This receives +12 VDC, and sends a video signal from the camera. When a synchronizing signal

generator is connected to this plug and an external synchronizing signal (HD/VD signal) is applied,

the camera can be operated synchronously with the external signal.

75Ωterminal switch (Terminal of external synchronizing HD/VD input signal)

Set this switch to OFF when not terminated. The factory setting is ON.

HD/VD signal input/output selector switch

Set to INT to output the HD/VD signals from the camera, and EXT to input external HD/VD signals.

The factory setting is EXT.

MODE SELECT switch

Shutter speed setting (MODE SELECT switch bit 1 to 4)

Set to the shutter speed suitable for the shooting conditions. For each setting position, refer to

P. 7. The factory setting position is shutter OFF.

Reset restart/External trigger mode setting (MODE SELECT switch bit 5 to 7)

For each setting position, refer to P. 8 to 13. The factory setting position is NORMAL.

3Trigger polarity setting (MODE SELECT switch bit 8)

Selects the polarity of an externally inputted trigger.

OFF: Positive ON: Negative

The factory setting position is OFF.

4Field accumulation/Frame accumulation setting (MODE SELECT switch bit 9)

For the mode setting, refer to P. 6. The factory setting position is Field accumulation.

5Gain selector switch setting (MODE SELECT switch bit 0)

This switch selects the modes OFF (fixed) or ON (manual). The factory setting is OFF (fixed).

Manual gain (M GAIN) control knob

This adjusts the gain of a video signal when the gain mode is set to ON by the MODE SELECT

switch bit 0 on step 5. The factory setting is the fully counterclockwise position.

3. CONNECTIONS

Standard Connection

Camera Cable

(optional)

Image processor

Lens

IK-53N

IK-52N

456

11 12

Cautions on Connection

• When connecting the camera cables, be sure to turn off the camera and the other equipment

connected.

• When using another lens, the best camera performance of this camera may not be obtained.

(For example, low resolution may occur, and flare, ghost or shading may occur)

• Use the DC power source described below.

• Power supply voltage: +10.5V to +15V

• Current rating: More than 830 mA

• Ripple voltage: Less than 50 mV(p–p)

Connector Pin Assignments

No.

External synchroniza-

tion mode (HD/VD)

GND

DC+12V

Video output (GND)

Video output (signal)

HD input (GND)

HD input (signal)

VD input (signal)

GND –

–

VD input (GND)

Reset restart

GND

DC+12V

Video output (GND)

Video output (signal)

HD input (GND)

HD input (signal)

Reset (signal)

GND –

VIDEO INDEX output

(signal)

–

Reset (GND)

External trigger mode

GND

DC+12V

Video output (GND)

Video output (signal)

HD input (GND)

HD input (signal)

VD input (signal)

GND –

VIDEO INDEX output

(signal)

Trigger pulse input

(signal)

VD input (GND)

Connector:

HR10A–10R–12PB by HIROSE electronics Co. Ltd

Internal synchroniza-

tion output signal

GND

DC+12V

Video output (GND)

Video output (signal)

HD output (GND)

HD output (signal)

VD output (signal)

GND –

–

VD output (GND)

4. SETTING

4-1. Field accumulation/Frame accumulation

This switch selects the potential accumulation mode of the CCD output signal. The mode can

be set with the MODE SELECT switch bit 9 on the rear panel.

ON OFF

EXT INT

HD/VD

75Ω

SHT

TRG

M.G

MIN MAX

M GAIN

VIDEO OUT

DC IN/SYNC

FRM

Field accumulation

Frame accumulation

9 9

Rear

MODE SELECT Switch

4-2. Electronic Shutter

This can be set with the MODE SELECT switch located on the rear panel.

Description of the MODE SELECT Switch

*The electronic shutter cannot be used in the reset-restart operation.

ON OFF

EXT INT

HD/VD

75Ω

SHT

TRG

M.G

MIN MAX

M GAIN

VIDEO OUT

DC IN/SYNC

FRM

Rear MODE SELECT Switch

Bits 1 to 4 : Shutter speed selection*

Bits 5 to 7 : External trigger mode selection

Bit 8 : Trigger polarity selection (Positive/Negative)

Bit 9 : Field accumulation/Frame accumulation

Bit 0 : Gain selection (OFF/ON)

Normal Shutter

This mode permits a high-speed moving subject to be captured clearly with a shutter function

incorporating a continuously available video signal. Set bit 5 of the MODE SELECT switch to

OFF (i.e., the left side) as illustrated in the table below.

Normal

shutter

Reset restart

external trigger mode

OFF

1/100

1/250

1/500

1/4000

1/10000

1/50000

1/100000

1/1000

1/2000

(unit：second)

4-3. Reset Restart

Input of an external reset-restart signal (VD) permits one screen of information to be output at

an arbitrary timing. To set this mode, set the external trigger mode selection switch (i.e., MODE

SELECT switch bits 5, 6, and 7) as illustrated in the diagram below.

Long Term Exposure

When the camera is used and sufficient sensitivity cannot be obtained for the reset-restart

function under normal operating conditions, or when observation of the trail of a moving

subject is desired, the exposure time can be extended to allow high-sensitivity images to be

obtained. To achieve this, please input from an external source a VD signal that has an ex-

panded VD pulse and VD pulse interval.

Input Timing Chart Example

ON OFF

EXT INT

HD/VD

75Ω

SHT

TRG

M.G

MIN MAX

M GAIN

VIDEO OUT

DC IN/SYNC

FRM

Reset restart

Rear MODE SELECT Switch

External HD

External VD

(Internal VD)

VIDEO INDEX

VIDEO OUT

About 1H

V reset

Exposure period

External VD interval:more than 1V

Exposure period Exposure period

1V 1V

About 1H

V reset

4-4. External Trigger Mode

Input of an external trigger permits a high-speed moving object to be captured at the proper

position. Set the rear panel external trigger mode selection switch (i.e., MODE SELECT switch

bits 5, 6, and 7) as illustrated in the diagram below.

The following two modes are available for video timing.

• SYNC-NON RESET Mode

In this mode, the video is synchronized to VD after the trigger input.

When external HD*/VD is input: Sync is to external VD

When external HD*/VD is not input: Sync is to internal VD

*There is automatic determination of external sync or internal sync by the presence or

absence of external HD input.

• SYNC-RESET Mode

In this mode, reset is applied to the internal VD and the video is output after a fixed period

following the trigger pulse.

External Trigger Shutter Speed Setting

The following two methods are available for shutter speed setting.

•1 pulse trigger mode␣ (Setting by the MODE SELECT switch of the rear panel)

For shutter speed, refer to the table below.

ON OFF

EXT INT

HD/VD

75Ω

SHT

TRG

M.G

MIN MAX

M GAIN

VIDEO OUT

DC IN/SYNC

FRM

SYNC-NONRESET SYNC-RESET

REAR

MODE SELECT Switch

1/100

1/250

1/500

1/4000

1/10000

1/50000

1/100000

1/1000

1/2000

(unit：second)

NOTE

In the external trigger mode, the

camera is automatically set to Field

accumulation regardless of the

MODE SELECT switch bit 9 position.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Toshiba

Toshiba

Toshiba IK-WB21A - IP Network PTZ Camera Manual de usuario

Toshiba

Toshiba IK-C41R2 Manual de usuario

Toshiba

Toshiba IK-TF9C Manual de usuario

Toshiba

Toshiba CS9001 SERIES Manual de usuario

Toshiba

Toshiba CleverDragon CSCV90BC3 Manual de usuario

Toshiba

Toshiba IK-HR1S Manual de usuario

Toshiba

Toshiba IK-WB70A - IP/Network Camera, PoE Manual de usuario

Toshiba

Toshiba IK-HD1H Manual de usuario

Toshiba

Toshiba IK - TF1 Manual de usuario

Toshiba

Toshiba IK-WR31A Manual de usuario

Toshiba

Toshiba IK-WR04A Manual de usuario

Toshiba

Toshiba 625012200G Manual de usuario

Toshiba

Toshiba IK-DP20A Manual de usuario

Toshiba

Toshiba 27A43 Manual de usuario

Toshiba

Toshiba IK-WD01A - IP/Network Mini-dome Camera Manual de usuario

Toshiba

Toshiba IK-WD14A Manual de usuario

Toshiba

Toshiba IK-TF7C Manual de usuario

Toshiba

Toshiba IK-DF01A Manual de usuario

Toshiba

Toshiba IK-WF51R Manual de usuario

Toshiba

Toshiba IK-DF02ADAY Manual de usuario

Toshiba

Toshiba IK-64DNA Manual de usuario

Toshiba

Toshiba IK-TF5C Manual de usuario

Toshiba

Toshiba IK-WD04A Manual de usuario

Toshiba

Toshiba IK - TF1 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario