Toshiba E-studio 2802a Instrucciones originales

zRead all the manuals carefully before using this equipment, and be sure to keep it for future reference.

MULTIFUNCTIONAL DIGITAL SYSTEMS

Safety Information 1 (GB)

Safety Information

Preface

Thank you for purchasing the Toshiba Multifunctional Digital Systems.

The SAFETY INFORMATION describes the necessary precautions for using this TOSHIBA

Multifunctional Digital Systems.

For your added safety, be sure to read this booklet before using this equipment. The models

vary from region to region.

The following table shows combinations of the model name indicated on the front cover and the

model name given in the identification label.

If there is a model name in the note, the corresponding model is applicable. If not, the above

models are applicable.

Example:

e-STUDIO2309A/2809A: This is a note for using e-STUDIO2309A/2809A.

Trademarks

Other company and product names given in this manual or displayed in this software may be

the trademarks of their respective companies.

Disclaimer Notice

The following notice sets out the exclusions and limitations of liability of TOSHIBA TEC

CORPORATION (including its employees, agents and sub-contractors) to any purchaser or

user (‘User’) of the e-STUDIO2802A/2802AM/2802AF, or the e-STUDIO2309A/2809A,

including its accessories, options and bundled software (‘Product’).

1. The exclusion and limitations of liability referred to in this notice shall be effective to the

fullest extent permissible at law. For the avoidance of doubt, nothing in this notice shall be

taken to exclude or limit TOSHIBA TEC CORPORATION’s liability for death or personal

injury caused by TOSHIBA TEC CORPORATION’s negligence or TOSHIBA TEC

CORPORATION’s fraudulent misrepresentation.

2. All warranties, conditions and other terms implied by law are, to the fullest extent permitted

by law, excluded and no such implied warranties are given or apply in relation to the

Products.

Model name on the front cover Model name on the identification label

e-STUDIO2802A/2802AM/2802AF DP-2802A/2802AM/2802AF

e-STUDIO2309A/2809A DP-2309A/2809A

2 (GB) Safety Information

3. TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or

damage whatsoever caused by any of the following:

(a) use or handling of the Product otherwise than in accordance with the manuals, including

but not limited to Operator’s Manual, User’s Guide, and/or incorrect or careless handling or

use of the Product;

(b) any cause which prevents the Product from operating or functioning correctly which arises

from or is attributable to either acts, omissions, events or accidents beyond the reasonable

control of TOSHIBA TEC CORPORATION including without limitation acts of God, war, riot,

civil commotion, malicious or deliberate damage, fire, flood, or storm, natural calamity,

earthquakes, abnormal voltage or other disasters;

service technicians authorized by TOSHIBA TEC CORPORATION; or

(d) use of paper, supplies or parts other than those recommended by TOSHIBA TEC

CORPORATION.

4. Subject to paragraph 1, TOSHIBA TEC CORPORATION shall not be liable to Customer for:

(a) loss of profits; loss of sales or turnover; loss of or damage to reputation; loss of production;

loss of anticipated savings; loss of goodwill or business opportunities; loss of customers; loss

of, or loss of use of, any software or data; loss under or in relation to any contract;

(b) any special, incidental, consequential or indirect loss or damage, costs, expenses,

financial loss or claims

for consequential compensation;

whatsoever and howsoever caused which arise out of or in connection with the Product or the

use or handling of the Product even if TOSHIBA TEC CORPORATION is advised of the

possibility of such damages.

TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or

damage caused by any inability to use (including, but not limited to failure, malfunction, hang-

up, virus infection or other problems) which arises from use of the Product with hardware,

goods or software which TOSHIBA TEC CORPORATION has not directly or indirectly

supplied.

END USER SOFTWARE LICENSE AGREEMENT

INSTALLING OR OTHERWISE USING THIS SOFTWARE PRODUCT CONSTITUTES YOUR

ACCEPTANCE OF THE FOLLOWING TERMS AND CONDITIONS (UNLESS A SEPARATE

LICENSE IS PROVIDED BY THE SUPPLIER OF APPLICABLE SOFTWARE IN WHICH CASE

SUCH SEPARATE LICENSE SHALL APPLY). IF YOU DO NOT ACCEPT THESE TERMS, YOU

MAY NOT INSTALL OR USE THIS SOFTWARE, AND YOU MUST PROMPTLY RETURN THE

SOFTWARE TO THE LOCATION WHERE YOU OBTAINED IT.

Safety Information 3 (GB)

GRANT OF LICENSE:

This is a legal agreement between you, the end-user (“You”), and TOSHIBA TEC Corporation

(“TTEC”). This software, fonts (including their typefaces) and related documentation (“Software”)

is licensed for use with TTEC MFP on which it was installed to the designated device you use

(“System”) in accordance with the terms contained in this License Agreement. The copyright and

other intellectual property rights, title and ownership of Software is proprietary and belonging to

TTEC and its suppliers. TTEC disclaim responsibility for the installation and/or use of Software,

and for the results obtained by using Software. You may use one copy of Software as installed on

a single System, and may not copy Software for any reason except as necessary to use

Software on a single System. Any copies of Software shall be subject to the conditions of this

License Agreement. You may not, nor cause or permit any third party to, modify, adapt, merge,

translate, reverse compile, reverse assemble, or reverse engineer Software. You may not use

Software, except in accordance with this license. No title to the intellectual property in Software is

transferred to you and full ownership is retained by TTEC and its suppliers. Source code of

Software is not licensed to you. You may not perform modification, deletion, etc to the copyright

notice of Software (including in duplicate).You will be held legally responsible for any copyright

infringement, unauthorized transfer, reproduction or use of Software.

TERM:

This license is effective until terminated by TTEC or upon your failure to comply with any term of

this License Agreement. Upon termination, you agree to destroy all copies of Software. You may

terminate this license at any time by destroying Software and all copies.

DISCLAIMER OF WARRANTY:

Software is provided "AS IS" without warranty of any kind, either express or implied, including,

but not limited to, the implied warranties of merchantability, fitness for a particular purpose, title,

and non-infringement. TTEC disclaims any warranty relating to the quality and performance of

Software. If Software proves defective, You (and not TTEC) shall be responsible for the entire

cost of all necessary servicing, repair or correction. TTEC does not warrant that the functions

contained in Software will meet your requirements or that the operation of Software will be

uninterrupted or error free.

UPDATE AND DISCONTINUE:

TTEC may update, upgrade and discontinue Software without any restriction.

THIRD PARTY SOFTWARE:

There are cases in which third party software is contained in Software (including future updated

and upgraded versions). Such third party software is provided to you on different terms from

those of this License Agreement, in the form of term stated in the License Agreement with the

suppliers or the readme files (or files similar to readme files) separately from this License

Agreement (“Separate Agreements, etc.”). When you use the third party software, you must

comply with the term of the third party software stated in the Separate Agreements, etc. Except

the term of the third party software, you must comply with the term stated in this License

Agreement.

4 (GB) Safety Information

LIMITATION OF LIABILITY:

IN NO EVENT WILL TTEC BE LIABLE TO YOU FOR ANY DAMAGES, WHETHER IN

CONTRACT, TORT, OR OTHERWISE (except personal injury or death resulting from negligence

on the part of TTEC), INCLUDING WITHOUT LIMITATION ANY LOST PROFITS, LOST DATA,

LOST SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES

ARISING OUT OF THE USE OR INABILITY TO USE SOFTWARE, EVEN IF TTEC OR ITS

SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, NOR FOR

THIRD PARTY CLAIMS.

U.S. GOVERNMENT RESTRICTED RIGHTS:

The Software is provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the U.S.

Government is subject to restrictions set forth in subdivision (b)(3)(ii) or (c)(i)(ii)of the Rights in

Technical Data and Computer Software Clause set forth in 252.227-7013, or 52.227-19 (c)(2) of

the DOD FAR, as appropriate.

GENERAL:

You may not sublicense, lease, rent, assign or transfer this license or Software. Any attempt to

sublicense, lease, rent, assign or transfer any of the rights, duties or obligations hereunder is

void. You agree that you do not intend to, and will not ship, transmit, export or re-export (directly

or indirectly) Software, including any copies of Software, or any technical information contained

in Software or its media, or any direct product thereof, to any country or destination prohibited by

government of Japan, the United States and the relevant country. This license shall be governed

by the laws of Japan or, at the election of a Supplier of TTEC concerned with a dispute arising

from or relating to this Agreement, the laws of the Country designated from time to time by the

relevant Supplier of TTEC. If any provision or portion of this License Agreement shall be found to

be illegal, invalid or unenforceable, the remaining provisions or portions shall remain in full force

and effect.

YOU ACKNOWLEDGE THAT YOU HAVE READ THIS LICENSE AGREEMENT AND THAT

YOU UNDERSTAND ITS PROVISIONS. YOU AGREE TO BE BOUND BY ITS TERMS AND

CONDITIONS. YOU FURTHER AGREE THAT THIS LICENSE AGREEMENT CONTAINS THE

COMPLETE AND EXCLUSIVE AGREEMENT BETWEEN YOU AND TTEC AND ITS

SUPPLIERS AND SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR

WRITTEN, OR ANY OTHER COMMUNICATION RELATING TO THE SUBJECT MATTER OF

THIS LICENSE AGREEMENT.

Contractor/Manufacturer is TOSHIBA TEC Corporation, 1-11-1, Osaki, Shinagawa-ku, Tokyo,

141-8562, Japan

Security Precautions

In order to make correct use of this product’s security function, first read the following

precautions carefully. Be sure to assign administrators who have enough capability to sustain

responsible management since significant privileges for managing and handling this equipment

will be given them.

To Administrators

yTo avoid physical security problems, such as hardware removal or inappropriate disassembly

at the installation site, take all necessary measures, such as checking who enters and leaves

the site.

Safety Information 5 (GB)

yWhen connecting this product with an outer network such as the Internet, only operate it in a

network environment protected by a firewall, etc. to prevent information from being leaked

due to incorrect settings or avoid illegal access by unauthorized users.

yTo prevent the configuration settings from being altered improperly or similar, before you use

this product, change the administrator password set by factory default. Also, be sure

periodically to change each password set for this product.

yIn order to make proper use of the network function and the department management

function, be sure to read the TopAccess Guide and User’s Guide first.

yBe sure to understand the security policy and its procedure in your organization, and manage

and operate this equipment according to the policy after first reading the operator's manual.

Then explain the security instructions to general users who are authorized to use this

equipment to let them conform to the security rule.

yProvide general users with the appropriate privilege of using this equipment and keep

supervising its correct operation.

yAlways check if the network function or the department management function is enabled in

order to maintain security. Should you happen to come across any abnormality, contact your

service technician immediately. Refer to the TopAccess Guide and User’s Guide for the

checking method.

To general users

yAfter you have finished operating the equipment, be careful not to forget to remove any

originals, printed paper or USB storage devices.

yChange the password regularly. Make sure not to use any predictable number such as your

birthday or employee ID number, and keep it secret.

yDo not leave the equipment during the performance of the job since your originals may be

seen or the output paper could be taken by someone.

Notice to Users

After a suitable place has been selected for the installation of the e-STUDIO2802A/2802AM/

2802AF, or the e-STUDIO2309A/2809A, please do not change it. Avoid excessive heat, dust,

vibration and direct sunlight. Also, provide proper ventilation as the copier emits a small

amount of ozone.

The unit is classified as Class 1 Laser Product according to IEC60825-1:2007 including

amendments.

The unit uses laser diodes with a max. output of 5 mW, a wavelength of 785 nm, pulse

duration 1.25 µs.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

WARNING

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

6 (GB) Safety Information

For the U.S.A. only

Indicates that the products affixing this mark use laser and potential risk and

hazard of eye or optic damage and/or skin burns if not avoided. Please follow

the cautions described near this mark.

Indicates that the locations affixing this mark are high temperature and have

potential risk and hazard of skin burns and/or relating damage if not avoided.

Please do not touch the location and its peripheral area.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

WARNING

Changes or modification made to this equipment, not expressly approved by TOSHIBA TEC

or parties authorized by TOSHIBA TEC, could void the user’s authority to operate the

equipment.

User Safety

This TOSHIBA Multifunctional Digital Systems does not produce laser radiation hazardous to

the user. It is certified as a Class 1 laser product under the U.S Department of Health and

Human Services (DHHS) Radiation Performance Standard according to the Radiation

Control Health and Safety Act of 1968 including amendments.

Protective housing and external covers completely confine the laser beam light emitted inside

the Multifunctional Digital Systems. The laser beam cannot escape from the machine during

any phase of user operation.

Regulations implemented on August 2, 1976 by the Bureau of Radiological Health (BRH) of

the U.S Food and Drug Administration apply to laser products manufactured from August

1,1976. Laser products marketed in the United States must comply with these regulations.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

Safety Information 7 (GB)

For the U.S.A. and Canada

For Canada only

For the EU only

Regulatory Information

Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle, a program

of the Rechargeable Battery Recycling Corporation. For more information and for drop-off

locations, visit www.rbrc.org or call 1-800-822-8837.

Notice regarding CR coin cell batteries, applicable to California, U.S.A. only: Perchlorate

Material - special handling may apply.

See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/

California Proposition 65 Warning: USA-California only

This Product contains chemicals known to the State of California to cause cancer, birth

defects, or other reproductive harm.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Working environment

From EMC (Electromagnetic Compatibility) point of view, the operation of this product is

being restricted in following environments:

yMedical Environments: This product is not certified as a medical product according to the

Medical Product Directive 93/42/EEC.

yDomestic environments (e.g. a private living room with TV / Radio sets in the nearby

surrounding area) because this is a so called EMC class A product. In a domestic

environment this product may cause radio interference in which case the user may be

required to take adequate measures!

Any consequences resulting from the use of this product in restricted working environments

are not the responsibility of TOSHIBA TEC.

The consequences of the use of this product in restricted working environments may be an

electromagnetic interference with other devices or machines in the nearby surrounding area.

This can result into malfunction including data loss / data error pertaining to this product or

the other devices / machines involved in the electromagnetic interference.

Furthermore, for general safety reasons, the use of this product in environments with

explosive atmospheres is not permitted.

CE compliance

This product is labelled with the CE mark in accordance with the provisions of the applicable

European Directives, notably the Low Voltage Directive 2006/95/EC, the Electromagnetic

Compatibility Directive 2004/108/EC, the RoHS Directive 2011/65/EU for this product and the

electric accessories, the Radio Equipment and Telecommunications Terminal Equipment

Directive 1999/5/EC for the telecommunication accessories.

CE marking is the responsibility of TOSHIBA TEC GERMANY IMAGING SYSTEMS GmbH,

Carl-Schurz-Str. 7, 41460 Neuss, Germany, phone +49-(0)-2131-1245-0.

For a copy of the related CE Declaration of Conformity, please contact your dealer or

TOSHIBA TEC.

Warning:

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

8 (GB) Safety Information

For India only

Following information is for EU-member states only:

This product is marked according to the requirement in EU-Directive on Waste

electrical and electronic equipment - WEEE.

The use of the symbol indicates that this product may not be disposed as unsorted municipal

waste and has to be collected separately. By ensuring this product is disposed of correctly, you

will help prevent potential negative consequences for the environment and human health,

which could otherwise be caused by inappropriate waste handling of this product.

For more detailed information about the take-back and recycling of this product please contact

your supplier where you purchased the product.

Following information is for EU-member states only:

Disposal of batteries and/or accumulators based on EU-Directive on batteries

and accumulators and waste batteries and accumulators.

By ensuring that batteries and/or accumulators are disposed of correctly, you will help prevent

potential negative consequences for the environmental and human health, which could

otherwise be caused by inappropriate waste handling of this product.

For more detailed information about the take-back and recycling of batteries and/or

accumulators, please contact your supplier where you purchased this product.

This device is not intended for use in the direct field of view at visual display workplaces.

To avoid incommoding reflections at visual display workplaces this device must not be placed

in the direct field of view.

Following information is only for India:

The use of the symbol indicates that this product may not be treated as

household waste. By ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling of

this product.

For more detailed information about the take-back and recycling of this

product, please contact your supplier where you purchased the product.

Otros manuales para e-studio 2802a

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Impresora todo en uno de Toshiba

Toshiba

Toshiba e-studio 2822AM Manual de usuario

Toshiba

Toshiba GA-1190 Manual de usuario

Toshiba

Toshiba e-STUDIO Instrucciones de instalación y mantenimiento

Toshiba

Toshiba E-studio 556 Manual de usuario

Toshiba

Toshiba E-studio306lp Manual de usuario

Toshiba

Toshiba e-studio 202L Manual de lista de piezas

Toshiba

Toshiba e-STUDIO4500c Manual de usuario

Toshiba

Toshiba GA-1201 Manual de usuario

Toshiba

Toshiba E-STUDIO2505AC Manual de usuario

Toshiba

Toshiba e-STUDIO FASTstart 200L Manual de usuario

Toshiba

Toshiba E-studio 5520c Manual de usuario

Toshiba

Toshiba E-Studio 5506AC Instrucciones de funcionamiento

Toshiba

Toshiba e-STUDIO 2303AM Manual de usuario

Toshiba

Toshiba e-STUDIO 165 Manual de usuario

Toshiba

Toshiba e-STUDIO556 Manual de usuario

Toshiba

Toshiba e-studio2505f Instrucciones de instalación y mantenimiento

Toshiba

Toshiba e-studio555 Manual de usuario

Toshiba

Toshiba e-STUDIO2500c Manual de usuario

Toshiba

Toshiba E-STUDIO 2500C Manual de usuario

Toshiba

Toshiba E-STUDIO2000AC Manual de usuario

Toshiba

Toshiba E-STUDIO 2500C Manual de usuario

Toshiba

Toshiba e-studio 2040c Manual de usuario

Toshiba

Toshiba e-STUDIO 600 Manual de usuario

Toshiba

Toshiba e-STUDIO3510c Manual de usuario

Manuales populares de Impresora todo en uno de otras marcas

Triumph Adler

Triumph Adler DC 2016 Manual

Epson

Epson WorkForce WF-2510 Guía del usuario

Epson

Epson Stylus Scan 2000 Manual de instalación y operación

Epson

Epson PictureMate Snap PM 240 Manual de instrucciones

Konica Minolta

Konica Minolta bizhub C35 Manual de usuario

Brother

Brother MFC-J430w Manual de usuario

Konica Minolta

Konica Minolta BIZHUB 558 Manual de usuario

Lexmark

Lexmark MX710 Series Manual

Brother

Brother MFC-9760 Manual de usuario

Lexmark

Lexmark XC8155 Manual de usuario

Lexmark

Lexmark X642E Manual de usuario

Sharp

Sharp MX-2310U Guía

Aficio

Aficio 200 Manual de usuario

Canon

Canon ImageCLASS 2300 Manual

Ricoh

Ricoh Pro C900 Manual de usuario

Lexmark

Lexmark X925 Manual de usuario

Brother

Brother Business Smart MFC-J4510dw Manual de usuario

Epson

Epson Stylus CX8400 Series Manual de usuario

Toshiba e-studio 2802a Instrucciones originales

Manuales populares de Impresora todo en uno de otras marcas