Toro 08865 Manual de usuario

Form No. 3459-473 Rev B

Laser Level Installation Kit

Field Pro

6040 T raction Unit

Model No. 08865

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure Description

Qty .

Use

No parts required

–

Prepare the machine.

No parts required

–

Remove the hood.

Bolt (3/8 x 1/2 inch)

Flat washer 4

Spacer

Locknut (3/8 inch)

Curved washer

Bushing 2

Receiver mast 1

Locknut (1/2 inch)

Thrust washer 1

Mast-support mount 1

Carriage bolt (1/2 x 2-1/2 inches)

Carriage bolt (3/8 x 1-1/4 inches)

Install the receiver mast.

Hydraulic hose (65 cm or 25-1/2 inches)

Hydraulic hose (48 cm or 19 inches)

Long hydraulic tube (mid-port)

Short hydraulic tube (mid-port)

Hydraulic tube (no port)

Hydraulic hose (90° elbow tting)

Long 90° elbow tting

Short 90° elbow tting

Straight tting

Carriage bolt (5/16 x 3/4 inch)

Control manifold

V alve bracket 1

Bolt (1/4 x 5/8 inch)

Nut (5/16 inch)

Install the hydraulics.

81 1 1 L yndale A venue South

Bloomington, MN 55420 Register at www .T oro.com.

Original Instructions (EN)

Printed in the USA

*3459-473*

Procedure Description

Qty .

Use

Bolt (1/4 x 5/8 inch)

Locknut (#6)

Carriage bolt (#10 x 5/8 inch)

Laser controller mount 1

Nut (#10)

Grommet

Screw (#6 x 1/2 inch)

Nut (1/4 inch)

Install the laser controller mount.

Switch bracket

Proximity switch 1

Switch plate

Carriage bolt (#10 x 5/8 inch)

Locknut (#10 inch)

Activator bracket 1

T orsion spring 1

Carriage bolt (1/4 x 3/4 inch)

Locknut (1/4 inch)

Install the operator presence switch.

Preparing the Machine

No Parts Required

Procedure

1. Park the machine on a level surface or move the

machine to a machine lift.

2. Engage the parking brake.

3. Raise the mid-mount attachment. Insert the

depth control pin into the T RANSPORT (T) position

to keep the mid-mount attachment up.

4. Shut of f the engine and remove the key .

5. W ait for all moving parts to stop and machine

components to cool.

6. Chock the wheels.

Removing the Hood

No Parts Required

Procedure

1. Remove the latches from the latch pins ( Figure

1).

g362440

Figure 1

1. Latch 2. Latch pin

2. Lift the hood from the machine ( Figure 2 ).

g362438

Figure 2

Installing the Receiver Mast

Parts needed for this procedure:

Bolt (3/8 x 1/2 inch)

4 Flat washer

Spacer

Locknut (3/8 inch)

Curved washer

2 Bushing

1 Receiver mast

Locknut (1/2 inch)

1 Thrust washer

1 Mast-support mount

Carriage bolt (1/2 x 2-1/2 inches)

Carriage bolt (3/8 x 1-1/4 inches)

Procedure

1. Install the mast-support mount to the machine

as shown in Figure 3 .

g389485

Figure 3

1. Locknut (3/8 inch) 3. Carriage bolt (3/8 x 1-1/4

inches)

2. Mast-support mount

2. Install the mast to the mast-support mount as

shown in Figure 4 .

3. Install the upper part of the mast to the machine

fork as shown in Figure 4 .

g439863

Figure 4

1. Bolt (3/8 x 3-1/2 inches)

7. Mast

2. Flat washer

8. Locknut (1/2 inch)

3. Spacer

9. Thrust washer

4. Locknut (3/8 inch)

10. Installed mast-support

mount

5. Curved washer 1 1. Carriage bolt (1/2 x 2-1/2

inches)

6. Bushing

Installing the Hydraulics

Parts needed for this procedure:

Hydraulic hose (65 cm or 25-1/2 inches)

Hydraulic hose (48 cm or 19 inches)

Long hydraulic tube (mid-port)

Short hydraulic tube (mid-port)

Hydraulic tube (no port)

Hydraulic hose (90° elbow tting)

Long 90° elbow tting

Short 90° elbow tting

Straight tting

Carriage bolt (5/16 x 3/4 inch)

Control manifold

1 V alve bracket

Bolt (1/4 x 5/8 inch)

Nut (5/16 inch)

Procedure

W ARNING

Hydraulic uid escaping under pressure can

penetrate skin and cause injury . Fluid injected

into the skin must be surgically removed

within a few hours by a doctor familiar with

this form of injury; otherwise, gangrene may

result.

• Ensure that all hydraulic-uid hoses

and lines are in good condition and all

hydraulic connections and ttings are tight

before applying pressure to the hydraulic

system.

• Keep your body and hands away from

pinhole leaks or nozzles that eject

high-pressure hydraulic uid.

• Use cardboard or paper to nd hydraulic

leaks; never use your hands.

1. Ensure the stop pin is in the transport and

maintenance position holding the tool up.

2. Move the valve control levers forward and

reverse to release internal pressure in the

hydraulic hoses and tubes.

3. Remove the existing hoses from the cylinder

and the control valve ( Figure 5 ).

g389238

Figure 5

1. Existing hoses for the cylinder

4. Remove the 90° elbow tting from the cooler

and at the front of the control valves ( Figure 6

and Figure 7 ).

g389240

Figure 6

1. Control valve end 2. 90° elbow tting

g389239

Figure 7

1. Control valve end

5. Install the 90° elbow ttings, straight ttings, and

the bracket to the control manifold ( Figure 8 ).

g389237

Figure 8

1. 90° elbow tting (short)

4. V alve bracket

2. 90° elbow tting (long) 5. Bolt (1/4 x 5/8 inch)

3. Control manifold 6. Straight tting

6. Install the control manifold and bracket to the

machine as shown in Figure 9 .

g389329

Figure 9

1. Carriage bolt (5/16 x 3/4

inches)

3. Nut (5/16 inch)

2. Manifold with bracket

7. Use Figure 10 to identify the hydraulic tubes and

the hoses.

g389303

Figure 10

1. Hydraulic hose (90° elbow

tting)

4. Long hydraulic tube

(mid-port)

2. Hydraulic hose (48 cm or

19 inches)

5. Short hydraulic tube

(mid-port)

3. Hydraulic hose (65 cm or

25-1/2 inches)

6. Hydraulic tube (no port)

8. Install the hydraulic hose (90° elbow tting) to

the straight tting on the manifold, route it back

to the hydraulic uid cooler , and attach the 90°

elbow tting to the hydraulic uid cooler; refer to

Figure 10 ,Figure 1 1 , and Figure 12 .

Note: Ensure the hose is routed away from hot

surfaces, not rubbing on other parts, and not

being pinched.

g390663

Figure 1 1

1. Hydraulic hose (90° elbow tting)

g390674

Figure 12

1. 90° elbow tting connected to the hydraulic uid cooler

9. Install the short hydraulic tube (mid-port) to the

valve control and the 90° elbow tting (short) on

the manifold; refer to Figure 8 ,Figure 10 , and

Figure 13 .

g389241

Figure 13

1. Short hydraulic tube (mid-port)

10. Install the long hydraulic tube (mid-port) to the

valve control and the 90° elbow tting (long) on

the manifold; refer to Figure 8 ,Figure 10 , and

Figure 14 .

g389242

Figure 14

1. Long hydraulic tube (mid-port)

1 1. Install the hydraulic tube (no port) to the valve

control and the straight tting on the manifold;

refer to Figure 8 ,Figure 10 , and Figure 15 .

Tabla de contenidos

Otros manuales de Accesorios para tractores de Toro

Toro

Toro 08752 Manual de usuario

Toro

Toro 22414 Manual de usuario

Toro

Toro BU-003867 Manual de usuario

Toro

Toro Field Pro 604 Manual de usuario

Toro

Toro 79362 Manual de usuario

Toro

Toro 132-4164 Manual de usuario

Toro

Toro 136-8545 Manual de usuario

Toro

Toro 79181 Manual de usuario

Toro

Toro Sitework Systems 22420 Manual de usuario

Toro

Toro Direct Drive Power Box Rake Manual de usuario

Toro

Toro 08720 Manual de usuario

Toro

Toro Z MASTER 79402 Manual de usuario

Toro

Toro 25427 Manual de usuario

Toro

Toro Wheel Horse XT Series Manual de usuario

Toro

Toro 30728 Manual de usuario

Toro

Toro 23172 Manual de usuario

Toro

Toro 119-9604 Manual de usuario

Toro

Toro 04504 Manual de usuario

Toro

Toro 22521 Manual de usuario

Toro

Toro 78269 Manual de usuario

Toro

Toro 04479 Manual de usuario

Toro

Toro 04651 Manual de usuario

Toro

Toro 08733 Manual de usuario

Toro

Toro 136-6311 Manual de usuario

Manuales populares de Accesorios para tractores de otras marcas

Land Pride

Land Pride SGC0548 Manual de usuario

Swisher

Swisher Versa Commercial Pro VSP50 Manual de usuario

matev

matev FPS-FKH-Kioti CX 2510 Manual de usuario

matev

matev SCA-130 Manual de usuario

Avantco

Avantco A425119 Manual de usuario

FTS

FTS G-FTL Series Manual de usuario

Sami

Sami 150-50 Manual de usuario

CAMSO

CAMSO TTS 30 Series Manual de usuario

Luda

Luda tractorCam S Manual de usuario

HLA

HLA BALE KNIFE Series Manual de usuario

P.Lindberg

P.Lindberg 9059890 Instrucciones de operación

Ventrac

Ventrac KD482 Manual de usuario

Original Tractor Cabs

Original Tractor Cabs 4421381 Hoja de datos

Grouser Products

Grouser Products 760 Manual de usuario

Degelman

Degelman Landroller Manual de programación

Bush Hog

Bush Hog BS1 Series Manual de usuario

MX MX A104 Manual de usuario

Bush Hog

Bush Hog DSP8 Manual de usuario