Torklift GlowStep Revolution Manual de usuario
OWNERS MANUAL
Part: A8002, A8003, A8004, A8005, A8006
A8102, A8103, A8104, A8105, A8106
GlowStep Revolution
Version 13 BY: RS 6/23/16
TECH SUPPORT (800) 246-8132
Parts Inventory (Hardware in Bolt Kit)
Item Image
Item Description
Quantity
3/8”-16 x 1” Grade 5 Hex Bolt
4
3/8” SS SAE Flat Washers
8
3/8” Lock Washers
4
3/8”-16 Grade 5 Hex Nuts
4
5/16”- 18 x 1.25” Grade 5 Hex
Bolts
4
5/16”-18 Grade 5 Hex Nut
4
5/16” USS Flat Washer
8
5/16” Lock Washer
4
1/4" x 1-3/8” Usable Bail Pin With
1/2” Spacer
1
7/32 Hex L Key
1
Parts Inventory (Hardware Preassembled)
Item Image
Item Description
Quantity
GlowStep Revolution Frame
(assembled)
1
GlowStep Assembly (assembled)
1
3/8”-16 x 1-3/4” Button Head
Socket Cap Screw
(Pre-Assembled)
2
3/8” SS SAE Flat Washers
(Pre-Assembled)
4
3/8”-16 Grade 8 Nylock Hex Nut
(Pre-Assembled)
2
3/8” x 3/4” x 3/8” Nylon Spacer
(Pre Assembled)
2
Page1
Installation of GlowStep Revolution
Step 1
Begin by removing the factory steps, and leveling the trailer on flat
ground.
Step 2
Determine the proper mounting height of the GlowStep Revolution
Frame. The top of the GlowStep Revolution Frame should sit as close
to the optimal mounting height as possible to allow for the most
adjustability when installed.
Refer to table 2.1 for the optimal mounting height as measured from
the ground to the top of the GlowStep Revolution Frame when the
trailer is leveled on flat ground.
Part Number
Mounting Height (inches)/(cm)
A8002, A8102
20.25 / 51.4
A8003, A8103
27.75 / 70.5
A8004, A8104
35.25 / 89.5
A8005, A8105
42.75 / 108.5
A8006, A8106
50.25 / 127.6
Table 2.1
Warning:
Do not use or apply weight to the GlowStep Revolution steps
while in the stored position. Doing so may cause damage to
the guide studs.
The 1/4" x 1-3/8" Bail Pin MUST be installed when the steps
are either deployed or in a stowed position. Failure to use bail
pin can result steps not being locked in a secured position.
See figure 6.3 and 6.4
Page2
Due to the variances in step opening and door heights, it may be
necessary to deviate from the optimal mounting height. The top of
the GlowStep Revolution frame should sit no lower than five inches
from the threshold of the door.
If two people are installing the GlowStep Revolution, then proceed to
Step 3A. If one person is installing the GlowStep Revolution, then
proceed to Step 3B.
Step 3A
Unfold the GlowStep Revolution as is seen in Figure 3.1A. One
person can hold the GlowStep Revolution Frame in place as needed
while the hardware is installed. The feet should be resting on the
ground to reduce the weight that is being held by the person. Proceed
to step 4.
Step 3B
Figure 3.1A
Hold in desired position here
Feet
Ground
Page3
Remove the GlowStep Revolution from the packaging. Lift one of
the step release levers and pull the GlowStep assembly out from the
GlowStep Revolution Frame. Remove the hardware attaching the
GlowStep assembly to the pivot arms as shown in figure 3.1B, using
the included Hex L-Key. Save this hardware, as it will be used later
to reattach the steps.
Figure 3.1B
Step 4
3/8” x 1-3/4” Button
Head Socket Cap Screw
3/8” SS SAE
Flat Washer
3/8” x 3/4" x 3/8”
Nylon Spacer
3/8”-16 Grade 8
Nylock Hex Nut
3/8” SS SAE
Flat Washer
Page4
The GlowStep Revolution Frame can be mounted with either 3/8"
hardware through the inner holes as seen in figure 4.1, or mounted
with 5/16" hardware through the outer holes as seen in figure 4.2.
Side brackets vary by manufacturer, and may need to be trimmed to
clear the hardware protruding through the sides of the GlowStep
Revolution Frame. If the width of your camper mounting brackets is
wider than the GlowStep Revolution frame, order A8020 GlowStep
Revolution Spacer Kit to increase the mounting width of the
GlowStep Revolution.
Once installed, torque the 3/8" hardware to 25 ft-lbs, or torque the
5/16" hardware to 15 ft-lbs.
3/8”-16 Grade 5
Hex Nuts
3/8” SS SAE
Flat Washers
3/8” Lock
Washers
Figure 4.1
3/8” SS SAE
Flat Washers
3/8”-16 x 1”
Grade 5 Hex
Bolts
5/16”-16 x 1-
1/4” Grade 5
Hex Bolts
Page5
Step 5 - Reattach GlowSteps
If the GlowSteps were removed for installation, the GlowStep
assembly can be reattached to the pivot arms at this time. See figure
3.1B.
Snug the 3/8"-16 Gr8 Nylock Nuts, then back them off approximately
1/4 turn. The steps should be able to pivot around the bolt.
Figure 4.2
5/16” USS
Flat Washers
5/16”-18 Grade
5 Hex Nuts
5/16” Lock
Washers
5/16” USS
Flat Washers
Este manual sirve para los siguientes modelos
10
Otros manuales de Escalera de Torklift
