Tork 209303A Instrucciones de construcción
Washroom Dispenser Service and Parts Manual
Tork Bath Tissue Roll Dispenser
209303A, 209305A Revision Date: 2-17-10
1 of 5
Tork Bath Tissue Roll Dispenser:
T26 System: 209303A (white), 209305A (quartz)
Dispenser Dimensions HxWxD (Inches):
14.2 x 6.3 x 6.46 (36.07 x 16 x 16.41 cm)
Bath Tissue Product Options:
110292A (Tork Advanced, 2 Ply, 1000 sheets)
110291A (Tork Advanced, 1 Ply, 2000 sheets)
Parts
Part Description Replacement SKU
STRIKE PLATE
MANDREL
RELEASE LEVER
HOOD PINS
HOOD
TORK LOCK
200262-10 or
200262-20
200260 KEY FOR
ALL TORK
DISPENSERS
200260 KEY
Washroom Dispenser Service and Parts Manual
Tork Bath Tissue Roll Dispenser
209303A, 209305A Revision Date: 2-17-10
Part Description with Replacement Instructions
Parts with SKUs listed are available for order as of the revision date on the manual. Contact an SCA
Sales Rep or the SCA Tissue Quality Coordinator to order these parts.
If no SKU is listed, the availability of the part is unknown. Please contact the SCA Tissue Quality
Coordinator for more information (see Contacting SCA section).
Replacement SKU Description & Replacement Instructions
STRIKE PLATE FOR LOCK
The strike plate is a small strip of metal that the lock engages when the cover is
closed. If the plate is bent, it can prevent the cover from closing and locking
properly. The strike plate can be removed with a Phillips head screwdriver.
MANDREL
Rides on track inside dispenser and supports the bath tissue rolls.
RELEASE LEVER
When the lower roll completely dispenses, the release lever allows the mandrel to
slide down into a position which allows the user access to the upper roll. Not
replaceable.
HOOD PINS
HOOD
To remove the cover, open the dispenser and remove the E-clips from the cover
pins. Slide the hood pins out and remove the cover. When the new cover is on,
use a needle nose pliers to put the E-clips back into the cover pins.
200262-10 or
200262-20 TORK LOCK
The lock can be replaced by removing the U-clip from the inside of the dispenser
with a pliers or screwdriver.
200260 KEY SCA 200260 KEY FOR ALL TORK DISPENSERS
Loading Instructions
1. Open the cover with the supplied
Tork key. Remove the mandrel by
pulling it downward and out of the
dispenser (1a) and install unwrapped
Tork bath tissue as shown (1b). Do not
try to pull the mandrel up through the
top of the dispenser.
2 of 5
Washroom Dispenser Service and Parts Manual
Tork Bath Tissue Roll Dispenser
209303A, 209305A Revision Date: 2-17-10
2. Replace the mandrel in the
dispenser by inserting it into the top,
noting it only fits one way (2a). Place
the roll into the top of the dispenser
(2b). Close the cover and remove the
Tork key.
Reloading Instructions
1. Open the cover with the supplied Tork
key. The spindle with the used core drops
out of the bottom of the dispenser (1a).
Remove the used core and place a full,
unwrapped roll on the spindle (1b). Do not
try to pull the mandrel up through the top
of the dispenser.
2. Lift the new roll up and
around (2a) until it is now
on the top (2b). Drop the
roll into the top of the
dispenser (2c). Close the
cover and remove the Tork
key (2d).
Preventive Maintenance
The Tork Bath Tissue dispenser should be cleaned any time there is heavy paper dust build-up
inside the dispenser. If paper dust is not a problem, approximately every year is a good
frequency for cleanings. The following is the recommended procedure to cleaning:
1) Open the dispenser and remove the rolls of paper.
3 of 5
Washroom Dispenser Service and Parts Manual
Tork Bath Tissue Roll Dispenser
209303A, 209305A Revision Date: 2-17-10
4 of 5
2) Clean out any paper dust. This can be done is several ways, such as, vacuuming, blowing out
with a can of compressed air (wear safety glasses), wiping out with a damp cloth, etc.
3) Clean the cover with a general all-purpose cleaner that is safe for plastics.
Troubleshooting
Problem: Any paper-related problem.
•Take note of the date code on the outside of the case of paper product. Then contact the
SCA Tissue Quality Coordinator and explain the problem.
Problem: Any other problem not stated above.
•Contact the SCA Tissue Quality Coordinator.
Contacting SCA
Before contacting SCA, locate and make note of the date code of the dispenser. The date code
for the 209303A and 209305A should be on a sticker on the inner back wall of the dispenser. To
contact the SCA Tissue Quality Coordinator, dial 1-866-722-6659 and press 6.
Washroom Dispenser Service and Parts Manual
Tork Bath Tissue Roll Dispenser
209303A, 209305A Revision Date: 2-17-10
209303A – 209305A Tork Bath Tissue Roll Dispenser
Mounting Instructions
5 of 5
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Dispensador de Tork
Tork
Tork Intuition Manual de usuario
Tork
Tork Elevation T2 Mini JBT Series Instrucciones de construcción
Tork
Tork W6 Guía de configuración
Tork
Tork Image Design Matic 460001 Manual de usuario
Tork
Tork S2 Manual de usuario
Tork
Tork Xpressnap N4 Manual de usuario
Tork
Tork Image Design 460013 Manual de usuario
Tork
Tork Matic Elevation H1 Manual de usuario
Tork
Tork Intuition 5511201 Manual de usuario
Tork
Tork 86ECO Instrucciones de construcción
Tork
Tork Elevation H2 Xpress Mini Instrucciones de construcción
Tork
Tork 430690 Manual de usuario
Tork
Tork S1 System Instrucciones de construcción
Tork
Tork H-7859 Manual de usuario
Tork
Tork Matic Manual de usuario
Tork
Tork Performance Maxi W2 Instrucciones de construcción
Tork
Tork 99A Instrucciones de construcción
Tork
Tork 93T Guía
Tork
Tork TREA 0060 Manual de usuario
Tork
Tork Xpressnap N4 System Manual de usuario
