Tohnichi CTB Manual de usuario

CTB Retightening Torque Wrench

Quick Start

1) Charge CTB using Tohnichi AC Adapter # QC-1 for approx 1hr until green light goes

on.

2) Keep wrench stable, with no movement while you press On button

3) Wrench will go through a gyro sensor stabilizing function “—-” will appear followed

by “good”. If “Error0” appears then sensor did not stabilize properly. Turn unit Off

and On again until “good” is display.

4) Setup Auto reset and Data Output functions by pressing “C”, then “MEM”, then “MD”

keys in that order.

5) “Ar” will show in the corner .The“0.0” setting is for manual reset, which means you

must press “MEM” key after each reading is taken. Using arrow keys, change setting

to show seconds after peak torque is achieved to automatically store reading into mem-

ory. Press “MEM” to save setting and proceed to next selection.

6) “do” will appear in the corner. Using arrow keys select data output methods: PC (to

computer), PRN (to printer), or IFR (infrared Data Tank R-DT100-3) Press “MEM” to

save selection.

7) Counter indicates “00” This is run mode. Use arrow keys to select a count number to

move into peak mode.

8) On a bolt that has already been tightened, position wrench on fastener, pull steady and

smoothly until green light turns on and buzzer will sound. Stop pulling.

9) As you are pulling value will indicate peak torque followed by “P” on the end. Once

bolt head starts to move sensor gives green light ,

CTB Retightening Torque Wrench

Quick Start

10) Value will change to initial tightening torque value. The “P” will no longer

be at the end of the value and displayed value will be lower. This reading

should be very close to the original tightened torque.

11) If you do not pull until ,green light goes on , “E-1” error alarm will sound

and display will flash. You must clear the display and start again.

12) To access statistical, functions move counter to the highest count number

that data is stored press “MD” to see total number in sample (N)

13) Press “MD” a second time to see “Hi” value in sample

14) Press “MD” a third time to see “Lo”value in sample

15) Press “MD” a fourth time to see “—” average value of sample.

For long term storage, use jack plug to shut off battery to gyro sensor. This will

help keep battery from draining quickly. After jack is removed, allow wrench to

stabilize 20 minutes before use.

For further assistance, call 1-847-272-8480

Contact us for information regarding downloading data to Excel file.

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Tohnichi

Tohnichi

Tohnichi TiQL Manual de usuario

Tohnichi

Tohnichi QLLS Manual de usuario

Tohnichi

Tohnichi CL2Nx8D-MH Manual de usuario

Tohnichi

Tohnichi DQL Manual de usuario

Tohnichi

Tohnichi CTA2-G Manual de usuario

Tohnichi

Tohnichi SF Manual de usuario

Tohnichi

Tohnichi QL25N Series Manual de usuario

Tohnichi

Tohnichi CSPFHW Manual de usuario

Tohnichi

Tohnichi CLE2 Manual de usuario

Tohnichi

Tohnichi QRSP-SP2-N Series Manual de usuario

Tohnichi

Tohnichi FH256MC Manual de usuario

Tohnichi

Tohnichi CMQSP Manual de usuario

Tohnichi

Tohnichi MTQL Manual de usuario

Tohnichi

Tohnichi QL Manual de usuario

Tohnichi

Tohnichi SP Manual de usuario

Tohnichi

Tohnichi QL2N Manual de usuario

Tohnichi

Tohnichi DATA TORK CEM3-G-WF Manual de usuario

Tohnichi

Tohnichi T-FHM Manual de usuario

Tohnichi

Tohnichi TW750N2 Manual de usuario

Tohnichi

Tohnichi DB SERIES Manual de usuario

Tohnichi

Tohnichi QSPCA Series Manual de usuario

Tohnichi

Tohnichi CTA2-G Manual de usuario

Tohnichi

Tohnichi YCL2 Manual de usuario

Tohnichi

Tohnichi CTB10N2X8D-G Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual