Timberwolf TW 13/75G Manual de usuario

CONTENTS

TIMBERWOLF

TW 13/75G

Section Page No.

INTRODUCTION 1

PURPOSE OF MACHINE 2

MACHINE DIMENSIONS & SPECIFICATIONS 2

PARTS LOCATION DIAGRAMS 3

SAFE WORKING 5

Operator’s Personal Protective Equipment Required 5

Basic Woodchipping Safety 5

General Safety Matters - Do’s and Dont’s 6

Noise Test 7

OPERATING INSTRUCTIONS 8

Safe Transportation 8

Delivery 8

Operator’s Personal Protective Equipment Required 8

Manual Controls 8

Starting the Engine 8

Stopping the Engine 9

Emergency Stopping 9

Daily Checks Before Starting 9

Starting to Chip 9

Chipping 9

Blade Wear 10

Blockages 10

SERVICE INSTRUCTIONS 11

Service Schedule 12

Safe Maintenance 13

Safe Lifting of Chipper 13

Spares 13

Copper Ease Safety Information 13

Engine Manufacturer’s Handbook 13

Change Blades 14

Check Fittings 15

Tension Drive Belts 15

Greasing Rotor Bearings 15

Anvil Changing 15

WARRANTY STATEMENT 16

EC DECLARATION OF CONFORMITY CERTIFICATE 17

IDENTIFICATION PLATES 18

DECALS 19

PARTS LISTS 22

A5 4th Feb 2013

TIMBERWOLF

TW 13/75G

Thank you for choosing this Timberwolf brushwood chipper. Timberwolf chippers are

designed to give safe and dependable service if operated according to the instructions.

IMPORTANT HEALTH AND SAFETY INFORMATION

Before using your new chipper, please take time to read this manual which contains

and explains the chipper controls. Failure to do so could result in:

- PERSONAL INJURY

- EQUIPMENT DAMAGE

- DAMAGE TO PROPERTY

- A MEMBER OF THE GENERAL PUBLIC BECOMING INJURED

This manual covers the operation and maintenance of the Timberwolf TW 13/75G. All

information in this manual is based on the latest product information available at the

time.

All the information you need to operate the machine safely and effectively is contained

within pages 2 to 10. Ensure that all operators are properly trained for operating this

machine, especially with regard to safe working practices.

Timberwolf's policy of constantly improving their products may involve major or minor

changes to the chippers or their accessories. Timberwolf reserves the right to make

changes at any time without notice and without incurring any obligation.

Due to improvements in design and performance during production there may be, in

some cases, minor discrepancies between the actual chipper and the text in this manual.

The manual should be considered a permanent part of the

machine and should remain with it if the machine is resold.

CAUTION or WARNING

BE AWARE OF THIS SYMBOL AND WHERE

SHOWN, CAREFULLY FOLLOW

THE INSTRUCTIONS.

This caution symbol indicates important safety messages in this manual.

When you see this symbol, be alert to the possibility of injury to yourself

or others, and carefully read the message that follows.

ALWAYS FOLLOW SAFE OPERATING AND MAINTENANCE PRACTICES

INTRODUCTION

TIMBERWOLF

TW 13/75G

Serial No. Location

The serial number can be

found on the identification

plate located on the side of

the rotor housing.

Designed to chip solid wood material up to 75mm in diameter and

capable of chipping over 0.75 tonnes of brushwood per hour.

DIMENSIONS

1600 mm, (815 mm with funnel removed)

1565mm (815mm with funnel removed)

800mm

TIMBERWOLF TW 13/75G SPECIFICATION

Engine type: Honda 4 stroke OHV

Maximum power: 9.6kW (13hp)

Cooling method: Air cooled

Overall weight: 188kg

Starting method: Recoil

Type of feed: Gravity

Maximum diameter material: 75 mm (3”)

Fuel capacity: 6.5 litres

Material processing capacity: 0.75 tonnes/hr

Fuel type: Unleaded petrol

The Timberwolf TW 13/75G

GRIP

FUNNEL

DISCHARGE

BUCKET

TOP ROTOR

HOUSING

BELT GUARD

ENGINE

PETROL TANK

AIR FILTER

COVER

DISCHARGE

HANDLE

OPENING HANDLE

ROTOR HOUSING

CATCH BOLT

SAFETY SWITCH

TIMBERWOLF

TW 13/75G

PARTS LOCATOR

TIMBERWOLF

TW 13/75G

ROTOR

FAN

BLADE

CUTTER BLADE

ROTOR DRIVE

PULLEY

ENGINE

PULLEY

REAR BEARING

HOUSING

ENGINE

PROTECTOR

PARTS LOCATOR

TIMBERWOLF

TW 13/75G

BASIC WOODCHIPPING SAFETY

The operator should be aware of the following points:

MAINTAIN A SAFETY EXCLUSION ZONE around the chipper of at least 10 metres for the

general public or employees without adequate protection. Use hazard tape to identify this

working area and keep it clear from debris build up. Chips should be ejected away from any

area the general public have access to.

HAZARDOUS MATERIAL - Some species of trees and bushes are poisonous. The chipping

action can produce vapour, spray and dust that can irritate the skin. This may lead to

respiratory problems or even cause serious poisoning. Check the material to be chipped before

you start. Avoid confined spaces and use a facemask if necessary.

BE AWARE when the chipper is processing material that is an awkward shape. The material can

move from side to side in the funnel with great force. If the material extends beyond the funnel,

the brash may push you to one side causing danger. Badly twisted brash should be trimmed

before being chipped to avoid thrashing in the feed funnel.

BE AWARE that the chipper can eject chips out of the feed funnel with considerable force. Always

wear full head and face protection.

ALWAYS work on the side of the machine furthest from any local danger, e.g. not road side.

WARNING

SAFE WORKING

The chipper will feed material through on its own. To do this, it relies on sharp

blades both on the feed rollers and the chipper rotor. To keep the blades sharp,

only feed the machine with clean brushwood. DO NOT put muddy/dirty wood,

roots, potted plants, bricks, stones or metal into the chipper.

OPERATOR'S PERSONAL PROTECTIVE EQUIPMENT REQUIRED

Chainsaw safety helmet fitted

with mesh visor and

recommended ear defenders to

the appropriate specifications.

Work gloves with elasticated

wrist.

Close fitting heavy-duty

non-snag clothing.

Face mask if

appropriate.

DO NOT

wear rings, bracelets, watches,

jewellery or any other items that

could be caught in the material

and draw you into the chipper.

Steel toe cap safety boots.

TIMBERWOLF

TW 13/75G

SAFE WORKING

GENERAL SAFETY MATTERS

DO’S AND DON’TS

DO NOT operate chipper unless available light is

sufficient to see clearly.

DO NOT use or attempt to start the chipper

without the feed funnel, guards and discharge unit

securely in place.

DO NOT stand directly in front of the feed funnel

when using the chipper. Stand to one side.

DO NOT allow -

DO NOT smoke when refuelling.

DO NOT let anyone who has not received

instruction operate the machine.

DO NOT climb on the machine at any time.

DO NOT handle material that is partially engaged

in the machine.

DO NOT touch any exposed wiring while machine

is running.

DO NOT use the chipper inside buildings.

- to enter the machine, as damage is likely.

ALWAYS stop the chipper engine before making

any adjustments, refuelling or cleaning.

ALWAYS check rotor has stopped rotating and

remove chipper ignition key before maintenance

of any kind, or whenever the machine is to be left

unattended.

ALWAYS check the machine is well supported and

cannot move.

ALWAYS operate the chipper with the engine set

to maximum speed when chipping.

ALWAYS check (visually) for fluid leaks.

ALWAYS take regular breaks. Wearing personal

protective equipment for long periods can be

tiring and hot.

ALWAYS keep hands, feet and clothing out of feed

opening, discharge and moving parts.

ALWAYS use the next piece of material or a push

stick to push in short pieces. Under no

circumstances should you reach into the funnel.

ALWAYS keep the operating area clear of people,

animals and children.

ALWAYS keep the operating area clear from

debris build up.

ALWAYS keep clear of the chip discharge tube.

Foreign objects may be ejected with great force.

ALWAYS ensure protective guarding is in place

before commencing work. Failure to do so may

result in personal injury or loss of life.

ALWAYS operate the chipper in a well ventilated

area - exhaust fumes are dangerous.

BRICKS STRING CLOTH PLASTIC STONES

METAL GLASS RUBBER ROOTS BEDDING

PLANTS

TIMBERWOLF

TW 13/75G

Noise levels above 80dB (A) will be experienced at the working position. Wear ear protection

at all times to prevent possible damage to hearing. All persons within a 4 metre radius must also

wear good quality ear protection.

SAFE WORKING

NOISE TEST

MACHINE: TW 13/75G

NOTES: Tested chipping 40mm x 40mm corsican pine 1.5m in length

96.2 dB

96 dB

95.9 dB92.9 dB

R= 4 metres

Guaranteed Sound Power: 120dB (A)

As required by Supply of Machinery (safety) regulations of 2008.

R= 10 metres

98 dB

103.1 dB

There are five controls on the Honda GX 390 K1 that are required for daily usage of the TW 13/75G

chipper.

IGNITION SWITCH

CHOKE

LEVER

FUEL VALVE

THROTTLE

CONTROL LEVER

Please refer to the Honda

engine manual for detailed

instructions of how to start

and control the GX390

engine.

OFF

STARTER

HANDLE

OPERATING INSTRUCTIONS 8

TIMBERWOLF

TW 13/75G

SAFE TRANSPORTATION

THE TW 13/75G chipper may be transported as a unit or with the feed funnel removed.

TAKE care when loading the TW 13/75G as it is 183 kg in weight.

STRAP the chipper down firmly before beginning a journey (do not use feed funnel handles to

strap down machine).

ENSURE no debris or water is trapped in the rotor housing that may spill during transit.

TURN the fuel valve OFF and keep the engine upright.

All Timberwolf TW 13/75G machines have a full pre - delivery inspection before leaving the factory and

are ready to use. Read and understand this instruction manual before attempting to operate the

chipper. In particular, read pages 5-7 which contain important health and safety information and advice.

CHAINSAW safety helmet fitted with visor

and recommended ear defenders to an

appropriate specification.

HEAVY-DUTY gloves with elasticated wrist area.

CLOSE - FITTING heavy-duty non-snag clothing.

SAFETY footwear.

FACE MASK (if appropriate).

See page 5 for more detailed information.

DELIVERY

OPERATOR’S PERSONAL PROTECTIVE EQUIPMENT REQUIRED

STARTING THE ENGINE

TURN the fuel valve to the ‘ON’ position.

MOVE the choke lever to the ‘CLOSE’ position. NOTE: Do not use the choke if the engine is

warm or the air temperature is high.

MOVE the throttle control lever slightly to the left.

TURN the ignition switch to the ‘ON’ position.

PULL the starter handle lightly until resistance is felt, then pull briskly.

CAUTION: Do not allow the starter handle to snap back against the engine. Return it gently

to prevent damage to the recoil mechanism.

AS the engine warms up, gradually move the choke lever to the ‘OPEN’ position.

POSITION the throttle control lever for the desired engine speed.

MANUAL CONTROLS

TIMBERWOLF

TW 13/75G

9OPERATING INSTRUCTIONS

Turn the ignition switch to the 'Off' position (as shown above).

EMERGENCY STOPPING

STOPPING THE ENGINE

MOVE the throttle control lever to idle and allow to run for one minute.

TURN the fuel valve to the ‘OFF’ position.

LOCATE the machine on firm level ground.

CHECK engine oil level.

CHECK the fuel valve is open.

CHECK all guards are in place.

CHECK the discharge unit is pointing in a safe direction.

CHECK the feed funnel to ensure no objects are inside.

For parts location see diagrams on pages 3 & 4.

DAILY CHECKS BEFORE STARTING

CHECK that the chipper is running smoothly.

STAND to one side of the feed funnel.

PROCEED to feed material into the feed funnel.

Wood up to 75 mm in diameter can be fed into the feed funnel. Enter it into the funnel butt end first.

Release the material before it engages the rotor. Some pieces of wood may move around significantly

whilst being chipped.

The wood will be drawn into the cutting blade quite quickly, be ready for this to happen. Stand well clear.

A piece of wood which is too tough or too large for the chipper will slow the engine down. When this

happens it is possible to hold back the branches that are being chipped and allow the engine to regain

its speed again.

If a piece of wood gets stuck in the funnel and it cannot be chipped due to its size or shape, it will need

to be removed. Trim the branch until it is a suitable shape for the chipper to accept.

STARTING TO CHIP

CHIPPING

WARNING Do not use or attempt to start the chipper without the protective

guarding and discharge unit securely in place. Failure to do so may

result in personal injury or loss of life.

Otros manuales para TW 13/75G

Tabla de contenidos

Otros manuales de Alegre de Timberwolf

Timberwolf

Timberwolf TW 13/75G Manual de usuario

Timberwolf

Timberwolf TW150FTR Manual de usuario

Timberwolf

Timberwolf PTO 100G Manual de usuario

Timberwolf

Timberwolf TW190TR Manual de usuario

Timberwolf

Timberwolf TW 280TDHB Manual de usuario

Timberwolf

Timberwolf TW 280TVGTR Manual de usuario

Timberwolf

Timberwolf TW 13/75G Manual de usuario

Timberwolf

Timberwolf TW 280HB Manual de usuario

Timberwolf

Timberwolf TW 230HB Manual de usuario

Timberwolf

Timberwolf TW 230DHB Manual de usuario

Timberwolf

Timberwolf TW 150VTR Manual de usuario

Timberwolf

Timberwolf Entec TW 190H Manual de usuario

Timberwolf

Timberwolf TW 230PAHB Manual de usuario

Timberwolf

Timberwolf TW 230DHB Manual de usuario

Timberwolf

Timberwolf TW190TDHB Manual de usuario

Timberwolf

Timberwolf tw pto 150h Manual de usuario

Timberwolf

Timberwolf TW 125PH Manual de usuario

Timberwolf

Timberwolf TW 160PH Manual de usuario

Timberwolf

Timberwolf TW 150DH Manual de usuario

Timberwolf

Timberwolf TW 280FTR (Petrol) Manual de usuario

Timberwolf

Timberwolf TW 150VTR Manual de usuario

Timberwolf

Timberwolf TW 230VTR Manual de usuario

Timberwolf

Timberwolf TW150DHB Manual de usuario

Timberwolf

Timberwolf TW 190TFTR Manual de usuario

Manuales populares de Alegre de otras marcas

Craftsman

Craftsman 79964 Manual de usuario

Frontier

Frontier WC1208 Manual de usuario

Viking

Viking GE 150 Manual de usuario

Victory

Victory WC-8H Manual de usuario

GTM Professional

GTM Professional GTS 1300 Manual de usuario

Yardbeast

Yardbeast YB3514 Manual de usuario

Patriot

Patriot Electric Motors Manual de usuario

Echo

Echo CH5540 Manual de usuario

DOSKO

DOSKO 13-21T-13H Manual de usuario

Craftsman

Craftsman 486.24516 Manual de usuario

Garland

Garland 1480 TQG Manual de usuario

Vermeer

Vermeer BC160XL Guía rápida

Value Leader

Value Leader z9400 Guía

Salsco

Salsco 600PTO Manual del producto

Cub Cadet

Cub Cadet 24A-424M710 Manual de usuario

Champion

Champion 91050 Manual

Kellfri

Kellfri 13-WC17H2 Manual de usuario

Salsco

Salsco 813XT Manual del producto