THORLABS TSP01 Manual de usuario
Environmental Measurement
TSP01
Operation Manual
2018
Version:
Date: 1.4
21-Nov-2018
Copyright © 2018 Thorlabs
Foreword
Contents 3
1 General Information 4
41.1 Ordering Codes and Accessories
2 Getting Started 5
52.1 Parts List
52.2 Requirements
52.2.1 Hardware Requirements 52.2.2 Software Requirements
62.3 Software Installation
3 Operating Instructions 7
73.1 Quick Start 113.2 Detailed GUI Description
113.2.1 Controls
123.2.2 Settings
133.2.3 Tab Measurement 133.2.4 Tab Table
143.2.5 Tab Graph
143.2.6 Graph Display Option Menus
153.2.7 Logging Panel 163.2.8 Save Data
163.2.9 Load Data
173.2.10 Export Settings
173.2.11 Import Settings 183.2.12 Device Information
4 Write Your Own Application 19
194.1 WYOA for TSP01 RevB Sensors
194.1.1 Driver Installation and Location for TSP01 RevB Sensors 214.1.2 Changing the Driver for TSP01 RevB
224.2 WYOA for Previous-Revision Sensors
234.2.1 Driver Installation and Location for Previous-Revision TSP01 sensors
254.2.2 Command Reference 254.2.2.1 IEEE488.2 Common Commands
264.2.2.2 SCPI Command Reference
5 Maintenance and Service 29
295.1 Version Information
6 Troubleshooting 30
7 Appendix 31
© 2018 Thorlabs
We aim to develop and produce the best solutions for your
applications in the field of optical measurement techniques. To help
us to live up to your expectations and constantly improve our
products, we need your ideas and suggestions. We and our
international partners are looking forward to hearing from you.
Thorlabs GmbH
Warning
Sections marked by this symbol explain dangers that might result in
personal injury or death. Always read the associated information
carefully before performing the indicated procedure.
Please read this advice carefully!
This manual also contains "NOTES" and "HINTS" written in this form.
Attention
Paragraphs preceded by this symbol explain hazards that could
damage the instrument and the connected equipment or may cause
loss of data.
Note
3
© 2018 Thorlabs4
TSP01
1 General Information
The TSP01 is a device of the size of a USB thumb drive that can be plugged to any USB port
for reading up to three different temperature values and relative humidity.
The combined humidity and temperature sensor is embedded into the USB stick, a second
NTC temperature sensor TSP-TH is included and can be connected to the housing. A third op-
tional temperature sensor can be plugged to the USB housing. External temperature sensors
can be an additional Thorlabs TSP-TH or any other NTC type sensor. The Thorlabs TSP01 Ap-
plication software allows to enter individual NTC parameters, such as R0 (reference resist-
ance), T0 (reference temperature) and the B coefficient.
The TSP01 can be run and data can be displayed in the Thorlabs TSP01 Application software
as a separate GUI. Alternatively, the TSP01 can be run from the Thorlabs' Beam Profiler Soft-
ware.
Further, users have the choice to write a separate application or use a third party GUI. For this,
please see the chapter Write-Your-Own-Application .
Attention
Please find all safety information and warnings concerning this product in the chapter Safety
in the Appendix.
1.1 Ordering Codes and Accessories
.
TSP01
Temperature and Humidity USB Sensor Probe with external temperature
sensor
TSP-TH
External temperature probe for TSP01
19
33
© 2018 Thorlabs
2 Getting Started
5
2 Getting Started
2.1 Parts List
Inspect the shipping container for damage.
If the shipping container seems to be damaged, keep it until you have inspected the contents
for completeness and tested the TSP01 mechanically and electrically.
Verify that you have received the following items within the package:
1. TSP01: Temperature and Humidity USB Sensor Probe
2. TSP-TH: External Temperature Probe for TSP01
3. USB Extension Cable, 1.8 m
4. Quick Reference
2.2 Requirements
The TSP01 is controlled and data read out is monitored through software on a connected PC.
Users have the choice to either use the Thorlabs TSP01 Application software as a separate
GUI or to run the TSP01 from other Thorlabs' software such as the Beam Profiler Software.
Users are also free to write a separate application or use a third party GUI. For this, please see
the chapter Write-Your-Own-Application .
The following are the requirements for the PC to be used for remote operation of the TSP01.
2.2.1 Hardware Requirements
.
CPU
1 GHz or higher
RAM
512 MB or more
Graphic Card
at least 32 MB memory
Graphic Resolution
min. 1024 x 768
Hard Disc
min. 100 MB of available disk space (32 bit)
min. 100 MB of available disk space (64 bit)
Interface
free USB 2.0 port, USB cable according the USB 2.0
specification
2.2.2 Software Requirements
The TSP01 software is compatible with the following operating systems:
·Windows®XP (32-bit) SP3
·Windows®Vista (32-bit, 64-bit)
·Windows®7 (32-bit, 64-bit)
·Windows®8.1 (32-bit, 64-bit)
·Windows®10 (32-bit, 64-bit)
Note
As of 12/2018, Thorlabs introduces the TSP01 revision B. These revised TSP01 devices are
labeled "RevB" on the underside and use an instrument driver that no longer requires NI-
VISA™. For operation of the previous version of the TSP01 without the RevB label, NI-VISA™
(version 5.1 or higher) is required for the driver.
19
© 2018 Thorlabs6
TSP01
The NI-VISA™engine can be installed from the following sources:
·The software CD shipped with previous-revision TSP01 sensors (not labeled RevB). The in-
staller includes NI-VISA™.
·The National Instruments' website www.ni.com
2.3 Software Installation
Please download the TSP01 Application from the software tab on the TSP01 website.
Attention
Do not connect the TSP01 to the PC during software installation! Please make sure that the in-
stallation is carried out completely, including the reboot requests.
·Save the ZIP file to your computer and unpack the archive.
·Double click the setup.exe to install Shield Wizard.
·Read and accept the End-user License Agreement.
·Note the Readme Information during the installation process:
"V 2.0: - Temperature sensor TSP01 RevB supported (includes a new library TLTSPB)
- NIVISA Runtime removed from installer. "
NI-VISA™ has been removed from the installer since it is not required for TSP01 sensors
labeled "RevB". TSP01 sensors without the RevB label will require the installation of NI-VISA™
software.
© 2018 Thorlabs
3 Operating Instructions
7
3 Operating Instructions
After installation of the software connect the TSP01 to a free USB 2.0 port.
Note
The TSP01 should always be positioned away from heat and humidity sources that are not of
interest for the measurement to prevent background. For this, the 1.8 m USB cable is supplied
to position the TSP01 away from the PC/HUB.
The operating system recognizes a USB device and automatically installs the device drivers.
Start the GUI from the desktop icon.
For detailed information on how to use the TSP01 Application software, please see
the chapter Detailed GUI Description .
3.1 Quick Start
This chapter gives a short overview on how to use the TSP01 Application. A detailed descrip-
tion of the GUI can be found in the chapter Detailed GUI Description .
At the first connect, you will be prompted to select the pre-
ferred unit for temperature display. Confirm your choice
with "OK". The software now automatically connects to the
TSP01 and the actual temperature and relative humidity
are displayed as measured on the internal sensor. If an ex-
ternal sensor is connected, it will be recognized and en-
abled automatically, and the temperature of the external
sensor is now displayed.
11
11
© 2018 Thorlabs8
TSP01
Tab Measurement
The Measurement tab displays the actual mea-
surement values of all enabled sensors in numeri-
cal values and within a bar.
The bar indication range can be set individually in
the Settings menu. Additionally, two limits can
be defined for each bar that control the bar color
(blue - green - red) depending on the actual value
with respect to these two limits.
Logging Panel
.
·Logging Control: Choose between: manual start/stop, timed log-
ging or logging of a number of samples.
·Measurement Interval: Set the logging interval (time between two
measurements) between 1 and 10000 seconds.
·Averaging: Averaging unchecked: A single measured value per
selected measurement interval will be logged.
Averaging checked: All values that are measured each second
within the selected measurement interval will be averaged and
only this average value will be logged. Only one single value will
be logged for both options.
·Time Axis Scale: Three selections are available: time in seconds,
time in hh:mm:ss and time stamp (date and time). The complete
time stamp will be displayed only in the Table Tab.
·Start / Stop Logging: This is a toggle button to start / stop log-
ging.
·Results: In this pane logging statistics are displayed.
12
Otros manuales para TSP01
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Instrumento de medición de THORLABS
THORLABS
THORLABS LLD1530 Manual de usuario
THORLABS
THORLABS PAX1000 Manual de usuario
THORLABS
THORLABS NPL52B Manual de usuario
THORLABS
THORLABS TIBERIUS Manual de usuario
THORLABS
THORLABS TSP01 Manual de usuario
THORLABS
THORLABS PM100A Manual de usuario
THORLABS
THORLABS ERM100 Manual de usuario
THORLABS
THORLABS PM10-3 Manual de usuario
THORLABS
THORLABS S1FC635 Manual de usuario
THORLABS
THORLABS HNL008R Manual de usuario
THORLABS
THORLABS PDA20H Manual de usuario
THORLABS
THORLABS INTUN Series Manual de usuario
THORLABS
THORLABS Redstone OSA305 Manual de usuario
THORLABS
THORLABS KSG101 Manual de usuario
THORLABS
THORLABS LD3000R Manual de usuario
THORLABS
THORLABS EVOA1550F Manual de usuario
THORLABS
THORLABS Blueline Series Manual de usuario
THORLABS
THORLABS Redstone OSA305 Manual de usuario
THORLABS
THORLABS DC2100 Manual de usuario
THORLABS
THORLABS CC6000 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario