THORLABS CCS Series Manual de usuario

Spectrometer

CCS Series Spectrometer

Quick Start Manual

2018

Version:

Date:

Item No.:

2.1

09-Jul-2018

M0009-510-422

Foreword

Contents

1General Information 3

31.1 Safety

51.2 Ordering Codes and Accessories

51.3 Requirements

2 Installation 6

62.1 Parts List

72.2 Installing Software

3Getting Started 12

4 Appendix 14

144.1 Certifications and Compliances

154.2 Warranty

164.3 Copyright and Exclusion of Reliability

174.4 Thorlabs 'End of Life' Policy (WEEE)

184.5 Thorlabs Worldwide Contacts

We aim to develop and produce the best solution for your application

in the field of optical measurement technique. To help us to live up to

your expectations and improve our products permanently we need

your ideas and suggestions. Therefore, please let us know about

possible criticism or ideas. We and our international partners are

looking forward to hearing from you.

Thorlabs GmbH

Warning

Sections marked by this symbol explain dangers that might result in

personal injury or death. Always read the associated information

carefully, before performing the indicated procedure.

Please read these advices carefully!

This manual also contains "NOTES" and "HINTS" written in this form.

Attention

Paragraphs preceded by this symbol explain hazards that could

damage the instrument and the connected equipment or may cause

loss of data.

Note

1 General Information

The CCS Series Spectrometer is designed for general laboratory use. Integrated routines allow

averaging, smoothing, peak indexing, as well as saving and recalling data sets.

Attention

Do not connect the CCS Series Spectrometer to a PC prior to installingh the OSA-SW

Application! The installation package includes CCS Series Spectrometer specific drivers and

software that must be installed before the CCS Series Spectrometer is connected to the PC for the

first time.

A troubleshooting section and detailed specifications of the various components are provided in

this manual. The description of the instrument driver commands can be found in the VXIpnp VISA

instrument driver package.

Application software OSA-SW

OSA-SW is an acronym for "Optical Spectrum Analyzer Software". This software can be used for

acquiring direct, transmittance and absorbance measurements in conjunction with Thorlabs' optical

spectrum analyzers and CCD spectrometers.

After the installation, the software is able to communicate with all Thorlabs CCD based CCS

Series Spectrometers and OSA20x Optical Spectrum Analyzers. Additionally, a number of virtual

devices are included to demonstrate the functionality of OSA-SW: five for OSA20x Analyzers and

one for CCS spectrometers.

1.1 Safety

Attention

The safety of any system incorporating the equipment is the responsibility of the

assembler of the system.

All statements regarding safety of operation and technical data in this instruction manual

will only apply when the unit is operated correctly as it was designed for.

The CCS Series Spectrometer must not be operated in explosion endangered

environments!

Do not obstruct the air ventilation slots in the housing!

Do not remove covers!

Do not open the cabinet. There are no parts serviceable by the operator inside!

This precision device is only serviceable if properly packed into the complete original

packaging including the plastic foam sleeves. If necessary, ask for replacement

packaging.

Refer servicing to qualified personnel!

Only with written consent from Thorlabs may changes to single components be made or

components not supplied by Thorlabs be used.

Attention

The following statement applies to the products covered in this manual, unless otherwise

specified herein. The statement for other products will appear in the accompanying

documentation.

CCS Series Spectrometer

Note This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Users that change or modify the product described in this manual in a way not expressly

approved by Thorlabs (party responsible for compliance) could void the user’s authority

to operate the equipment.

Thorlabs is not responsible for any radio television interference caused by modifications

of this equipment or the substitution or attachment of connecting cables and equipment

other than those specified by Thorlabs. The correction of interference caused by such

unauthorized modification, substitution or attachment will be the responsibility of the

user.

The use of shielded I/O cables is required when connecting this equipment to any and all

optional peripheral or host devices. Failure to do so may violate FCC and ICES rules.

Attention

Mobile telephones, cellular phones or other radio transmitters are not to be used within

the range of three meters of this unit since the electromagnetic field intensity may then

exceed the maximum allowed disturbance values according to IEC61326-1.

This product has been tested and found to comply with the limits according to IEC61326-

1 for using connection cables shorter than 3 meters (9.8 feet).

1 General Information

1.2 Ordering Codes and Accessories

Ordering code

Short description

CCS100(/M) 1)

CCS spectrometer, 350 - 700 nm

CCS175(/M) 1)

CCS spectrometer, 500 - 1000 nm

CCS200(/M) 1)

CCS spectrometer, 200 - 1000nm

M14L01

1 m SMA MMF Patch Cable, 50µm / 0.22 NA (to CCS100 and

CCS175)

FG200UCC

1 m SMA MMF Patch cable, 200µm / 0.22 NA, High OH (to

CCS200)

CVH100; CVH100/M

Cuvette holder (imperial and metric versions)

1) CCSxxx = imperial version, mounting holes 1/4-20;

CCSxxx/M = metric version, mounting holes M6x1

Attention

Make sure to use your CCS spectrometer only with the included fiber (see above table). If using a

different fiber, the Amplitude Correction Calibration will be affected!

1.3 Requirements

These are the requirements to the PC intended to be used for remote operation of the CCS Series

Spectrometer.

Minimum Hardware and Software Requirements

• Operating System: Windows Vista or Windows 7 (32 or 64 bit)

• Free USB 2.0 high speed port (Notice that a USB 1.1 port cannot be used)

• Processor: Intel Pentium 4 or AMD Athlon 64 3000+

• 2.0 GB RAM

• .NET framework 4.0 or higher

Recommended Hardware and Software Requirement

• Operating System: Windows 7, 64 bit

• Free USB 2.0 high speed port (Notice that a USB 1.1 port cannot be used)

• Processor: Intel Core i5 or AMD Athlon II

• 6.0 GB RAM

• .NET framework 4.0 or higher

Note

Please be aware that the OSA software requires a number of third party software installed on your

system. The installer checks for these software components and, if necessary, will install them

automatically. You will be notified accordingly.

CCS Series Spectrometer

2 Installation

Attention

Do not connect the CCS Series Spectrometer to a PC prior to install the OSA-SW Application!

The installation package includes CCS Series Spectrometer specific drivers and software that

must be installed before the CCS Series Spectrometer is connected to the PC for the first time.

2.1 Parts List

Inspect the shipping container for damage. If the shipping container seems to be damaged, keep it

until you have inspected the contents and you have inspected the CCS Series Spectrometer

mechanically and electrically.

Verify that you have received the following items within the package:

CCS Series Spectrometer

This CCS Series Spectrometer Quick Reference

CD-ROM with application software OSA-SW, drivers and PDF User Manual

USB 2.0 A-B mini cable, 1.5 meters

Optical Fiber, SMA to SMA, 50µm / 0.22 NA, 1 meter (CCS100, CCS175)

Quartz Fiber, SMA to SMA, 200µm / 0.22 NA, 1 meter (CCS200)

Trigger Input cable SMB to BNC

Attention

Make sure to use your CCS spectrometer only with the included fiber (see above table). If using a

different fiber, the Amplitude Correction Calibration will be affected.

CCS Spectrometer - Ports and Signal LEDs

(1)

USB port

(2)

Fiber input (SMA connector)

(3)

Status LED

(4)

Trigger Input (SMB connector)

2 Installation

2.2 Installing Software

Before installing OSA Software, please make sure that no CCS Series Spectrometer is

connected. After you insert the OSA Software installation CD an autorun menu will appear (see

figure below). If autorun is disabled on your system, you will have to browse the installation CD and

run

"[CD-Drive]:\Autorun\Autorun.exe":

Click to "Install Software":

Note

Please be aware that the OSA software requires a number of third party software installed on your

system. The installer checks for these software components and, if necessary, will install them

automatically. You will be notified accordingly.

Administrator privileges are required for installation. Please contact your system administrator if

you get an error message.

Installation steps are shown below in detail for an installation on a Windows 7© operating system.

After selecting "Install Software", the installer checks your system and determines the software

components that need to be installed.

CCS Series Spectrometer

Click "Install" to continue. The necessary software components are being installed, followed by

installation of device driver software. The installation of all components is described below.

NI VISA installation

Click "I accept...", then "Next>>" to continue:

Otros manuales para CCS Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de THORLABS

THORLABS

THORLABS CCS Series Manual de instrucciones

THORLABS

THORLABS GCM102 Manual de usuario

THORLABS

THORLABS PM100A Manual de usuario

THORLABS

THORLABS S120 Manual de usuario

THORLABS

THORLABS SP USB Series Manual de usuario

THORLABS

THORLABS INT-MZI Series Manual de usuario

THORLABS

THORLABS HTPS Manual de usuario

THORLABS

THORLABS HNL020R Manual de usuario

THORLABS

THORLABS S2011 Manual de usuario

THORLABS

THORLABS CS20K2 Manual de usuario

THORLABS

THORLABS LLD1530 Manual de usuario

THORLABS

THORLABS PDA20H Manual de usuario

THORLABS

THORLABS HRS015 Manual de usuario

THORLABS

THORLABS ERM100 Manual de usuario

THORLABS

THORLABS CVH100-COL Manual de usuario

THORLABS

THORLABS VEGA Series Manual de usuario

THORLABS

THORLABS LTS Series Manual de usuario

THORLABS

THORLABS HNLS008R Manual de usuario

THORLABS

THORLABS HNL008R Manual de usuario

THORLABS

THORLABS EDU-SPEB1 Manual de usuario

THORLABS

THORLABS PM300 Manual de usuario

THORLABS

THORLABS PM30-120 Manual de usuario

THORLABS

THORLABS SA200 Series Manual de usuario

THORLABS

THORLABS LTS150 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario