THORLABS CS20K2 Manual de usuario

LED UV Curing System

2020

CS20K2 (365 nm),

CS20K3 (385 nm),

CS20K4 (395 nm),

CS20K5 (405 nm)

Operation Manual

Version:

Date: 1.0

13-Nov-2020

Foreword

Contents

1 General Information 1

11.1 Ordering Codes and Accessories 21.2 Requirements 21.2.1 Hardware Requirements 21.2.2 Software Requirements

2 Getting Started 3

32.1 Parts List

3 Operating Instructions 4

43.1 Operating Elements 53.2 Basic Setup 63.3 Display Operation 63.3.1 Settings 73.3.2 Continuous Mode 73.3.3 Timer Mode 73.3.4 Configuration Mode 83.3.5 Slope Mode 93.3.6 Irradiance Mode 103.3.7 User Limit 103.3.8 About 103.4 Computer Interface 103.4.1 Software Installation 103.4.1.1 Install Device Drivers 113.4.2 Graphic User Interface (GUI) 123.4.2.1 Menu Bar 133.4.2.2 Continuous Mode 143.4.2.3 Timer Mode 143.4.2.4 Configuration Mode 153.4.2.5 Slope Mode 163.5 Foot Switch Operation 163.6 Control of Other LEDs Using CS2020 Driver

4 Maintenance and Service 17

174.1 Version Information 174.2 Troubleshooting

5 Appendix 19

195.1 Technical Data 205.2 Dimensions 225.3 Spectra

225.4 Safety 235.5 Manufacturer Address 245.6 Warranty 245.7 Copyright and Exclusion of Liability 255.8 List of Acronyms 265.9 Thorlabs Worldwide Contacts and WEEE Policy

We aim to develop and produce the best solutions for your

applications in the field of optical measurement techniques. To help

us to live up to your expectations and constantly improve our

products, we need your ideas and suggestions. We and our

international partners are looking forward to hearing from you.

Thorlabs GmbH

Warning

Sections marked by this symbol explain dangers that might result in

personal injury or death. Always read the associated information

carefully before performing the indicated procedure.

Please read this advice carefully!

This manual also contains "NOTES" and "HINTS" written in this form.

Attention

Paragraphs preceded by this symbol explain hazards that could

damage the instrument and the connected equipment or may cause

loss of data.

Note

CS20Kx

1 General Information

The Thorlabs LED spot UV curing systems CS20Kx are designed for curing (hardening) of ma-

terial like certain inks, coatings, or adhesives which are formulated with photoinitiators and re-

sins. When exposed to the correct energy and irradiance in the required band of UV light, poly-

merization occurs, such that the adhesives harden or cure. Usually, this reaction is a matter of

a few seconds. This can be advantageous for any application that requires critical alignment or

exact positioning. Applications include glass and plastic bonding, optical fiber coatings and

coating of flooring.

The CS20Kx system is availabe for four different wavelength ranges: 365 nm, 385 nm, 395 nm

and 405 nm, named CS20K2, CS20K3, CS20K4 and CS20K5 respectively. The system con-

sists of a CS2020 driver and a handheld light source with the respective LED and optics. Op-

tionally, different optics are available to vary the size of the focus spot.

The system can be operated using either the display on the CS2020 driver or remotely using

the software. For flexibility in operation, the software allows to limit exposure time, reproducibly

increase and decrease intensity and to store up to 10 user defined settings.

With the CAB-CS20 adapter cable, the CS2020 can alternatively be used with Thorlabs moun-

ted LEDs as an assembled system.

Attention

Please find all safety information and warnings concerning this product in the chapter Safety

in the Appendix.

1.1 Ordering Codes and Accessories

CS20K2 LED UV Curing System for applications at 365 nm. Included: CS2020 con-

trol unit; respective Handheld LED light source CS20H2 with safety shield

and goggles; power supply.

CS20K3 LED UV Curing System for applications at 385 nm. Included: CS2020 con-

trol unit; respective Handheld LED light source CS20H3 with safety shield

and goggles; power supply.

CS20K4 LED UV Curing System for applications at 395 nm. Included: CS2020 con-

trol unit; respective Handheld LED light source CS20H4 with safety shield

and goggles; power supply.

CS20K5 LED UV Curing System for applications at 405 nm. Included: CS2020 con-

trol unit; respective Handheld LED light source CS20H5 with safety shield

and goggles; power supply.

CS2020 LED UV Spot Curing System, Main Control Unit

Accessories:

CAB-CS20 Adapter Cable for Mounted LEDs

CS20A1 Foot Switch for CS2020 Driver with 2.0 m Connection Cable with 3.5 mm

Jack Plug

CS20A2 Collimation Adapter for CS2020 (included with Handheld LED light source)

CS20A3 Focusing Adapter for CS2020 (optional)

CS20Hx Handheld Light Source with LED for Defined Wavelength. To Purchase In-

dividual Handheld Units CS20Hx, please Contact Thorlabs.

1 General Information

Spare parts:

Power Supply ETC36-24 (24V DC 1.5A)

Stand for CS2020 Handheld LED Light Source

UV Protection Shield

Safety Glasses

For purchasing the above spare parts, please contact Thorlabs.

1.2 Requirements

These are the requirements to the PC intended to be used for remote operation of the CS20Kx.

1.2.1 Hardware Requirements

CPU: 1 GHz or higher

RAM: 1 GB

Graphic card with at least 32 MB memory

Hard disc with at least 100 MB free storage space

Free USB 2.0 port

USB cable according the USB 2.0 specifications

1.2.2 Software Requirements

The CS2010 software package is used for operation of the former product CS2010, CS20Kx

and the driver CS2020 and is compatible with the following operating systems:

·Windows®XP (32-bit) SP3

·Windows®Vista (32-bit, 64-bit)

·Windows®7 (32-bit, 64-bit)

·Windows®8.1 (32-bit, 64-bit)

·Windows®10 (32-bit, 64-bit)

For operation of the CS20Kx with the CS2010 software, NI-VISA™ (version 5.0.2 or higher) is

required. The NI-VISA™ engine comes with the Thorlabs CS2010 software available for down-

load from the CS20Kx software tab, or can be downloaded also from National Instruments'

website www.ni.com.

CS20Kx

2 Getting Started

2.1 Parts List

Please inspect the shipping container for damage. Do not cut through the cardboard. You might

need the box for storage or returns.

If the shipping container seems to be damaged, keep it until you have inspected the contents

mechanically and electrically.

Verify that you have received the following items within the package:

1. CS2020 Driver for CS20Kx

2. Wide Range Power Supply (24V DC 1.5A) and Power Cord

3. CS20Hx Handheld Light Source with CS20A2 Collimation Adapter and Holder

4. USB 2.0 Cable

5. Safety Glasses

6. Quick Reference CS20Kx

3 Operating Instructions

The CS20Kx can be operated via the display on the CS2020 or remotely, using the software

CS2010. The chapter Display Operation describes operation via the device display, the

chapter Computer Interface gives instructions for remote operation.

3.1 Operating Elements

LC Display with Background Illumination

Rotary Knob

ESC Button

OK Button

LED ON/OFF Button, Illuminated when LED is On

Sliding Lid to Protect the Input Aperture (7)

Input Aperture for Irradiance Measurement

Ventilation Outlet

Handheld Light Source with Rotating LED Head

Collimated UV LED Output - Warning

UV Protection Shield

LED ON/OFF Switch on Handheld Light Source

Holder for Handheld Unit

Warning Do NOT look into the output aperture! Do NOT direct the UV emission onto

skin, reflective surfaces or other people.

CS20Kx

Rear Panel:

Power Switch

LED Output (Connector for Hand Set)

3.5 mm Jack for Foot Switch

USB 2.0 Connector (Remote Computer)

DC Input

Serial Number

3.2 Basic Setup

Note

Do not cover the air ventilation and avoid overheating of the driver. Please pay attention to the

safety recommendations and the Occupational Health and Safety Regulations applying to your

workplace.

To setup the CS20Kx, install the CS2010 software package and driver package to your PC

prior to connecting the CS2020 to the PC. The software and driver package are available from

the CS20Kx software tab.

·Connect the handheld light source to the driver (jack “LED” (2) on the rear panel).

·Connect the power supply to mains outlet, using the supplied power cord.

·Connect the DC output of the power supply to the jack “24VDC 1.5A” (5) at the rear

panel.

·Switch on the driver using the switch (1) at the rear panel.

·Connect the driver to the control PC using the USB2.0 cable.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de THORLABS

THORLABS

THORLABS CCS Series Manual de usuario

THORLABS

THORLABS HLS635 Manual de usuario

THORLABS

THORLABS PM200 Manual de usuario

THORLABS

THORLABS GCM102 Manual de usuario

THORLABS

THORLABS VSD500 Manual de usuario

THORLABS

THORLABS HRP350 Manual de usuario

THORLABS

THORLABS LNR25 Series Manual de usuario

THORLABS

THORLABS CCS Series Manual de usuario

THORLABS

THORLABS M2MS-BC106N Series Manual de usuario

THORLABS

THORLABS ERM100 Manual de usuario

THORLABS

THORLABS PM5020 Manual de usuario

THORLABS

THORLABS LTS Series Manual de usuario

THORLABS

THORLABS PM10-3 Manual de usuario

THORLABS

THORLABS HNL008R Manual de usuario

THORLABS

THORLABS DC2100 Manual de usuario

THORLABS

THORLABS PM300 Manual de usuario

THORLABS

THORLABS LDM21 Manual de usuario

THORLABS

THORLABS ELL10(K) Manual de usuario

THORLABS

THORLABS PM160 Manual de usuario

THORLABS

THORLABS NPL52B Manual de usuario

THORLABS

THORLABS PM100USB Manual de usuario

THORLABS

THORLABS TIBERIUS Manual de usuario

THORLABS

THORLABS PMD5000 Manual de usuario

THORLABS

THORLABS FSL1030X1 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario