ThermoWorks 8689 Manual de usuario

ThermoWorks, Inc.

1762 W. 20 S. #100

Lindon, UT 84042

ph: 801-756-7705

www.thermoworks.com

8689 pH Meter

File and keep

It is recommended that you

before using to clear up the lazy effect

or to make the electrode wet if the pH

electrode dries out.

Check

will

Loosen

old

It is recommended

the meters

3. "pH " flashes while the meter is in

measurement mode. The LCD shows

the measured pH and temperature.

“pH” stop flash while the reading is

stable.

" "

4. Press key to freeze current

readings. "HLD" appears on the LCD.

Press " " key again to release.

Remove the cover

from the bottom

of meter to expose

the electrode.

Electrode cap

If the cap is too

tight, use pliers to

bracket the cap and

rotate to remove.

Don’t break the cap.

keep

This meter will shut off automatically after

20 minutes of inactivity. For operating a

longer period of time, you can disable

the sleep mode.

NOTE: The sleep mode will reset after

every power off.

After re-calibration, checking probe slope

and offset value may help to confirm

While

Before calibration, it is recommended that

you RESET the meter to delete all old

calibration information.

Caibration is necessary and should be done

regularly. It is recommended that this be

done everyday if the meter is used often.

The unique calibration design of the meter

features automatic buffer recognition to

avoid errors.

It is recommended to

calibrate pH7 first and then 4 or 10pH

for better accuracy result.

-pH3.00~5.00

-pH6.00~8.00

-pH8.50~10.50

The acceptable pH buffer range:

6. If the probe successfully

recognizes the buffer, the

buffer pH value and “CAL”

will stop flashing.

If your calibration buffer is not NIST,

press " " or “ “ to

3.00 to 5.00,

6.00 to 8.00, 8.50 to 10.50.

adjust the

calibrating point to the corresponding

buffer value of specific temperature. The

adjustable range is :

5. If the probe is damaged or the buffer is

not specified as following, the primary

LCD will keep flashing unless you escape

by turning off the meter.

8. Wait for 30 seconds, the meter completes

the calibration automatically if the reading

is stable enough.

9. Rinse the probe with de-ionized water

or a rinse solution (tap water...) after

calibration. Repeat step 3 ~ 8 to do

multiple point calibration or exit by turning

off the meter.

Otros manuales de Instrumento de medición de ThermoWorks

ThermoWorks

ThermoWorks IRT-2 Infrared Manual de usuario

ThermoWorks

ThermoWorks ThermaData WiFi TD2TC-K Manual de usuario

ThermoWorks

ThermoWorks PTR Manual de usuario

ThermoWorks

ThermoWorks BlueTherm One Manual de usuario

ThermoWorks

ThermoWorks ThermaQ WiFi Manual de usuario

ThermoWorks

ThermoWorks ThermaQ 2 Manual de usuario

ThermoWorks

ThermoWorks Classic Thermapen Manual de usuario

ThermoWorks

ThermoWorks BlueTherm IR Manual de usuario

ThermoWorks

ThermoWorks I.R.K. Manual de usuario

ThermoWorks

ThermoWorks Therma K Manual de usuario

ThermoWorks

ThermoWorks ThermaQ Manual de usuario

ThermoWorks

ThermoWorks 3101 Manual de usuario

ThermoWorks

ThermoWorks BlueDOT TX-1400 Manual de instrucciones y seguridad

ThermoWorks

ThermoWorks HygroBug Manual de usuario

ThermoWorks

ThermoWorks 7000 Manual de usuario

ThermoWorks

ThermoWorks ThermaQ Blue Manual de usuario

ThermoWorks

ThermoWorks TW-USB-1 Instrucciones de funcionamiento

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario