Texmate FL-B101D40H Manual de usuario

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comMay-29-2009 FL-B101D40H DS (FL8) Page 1

Smart Tricolor or mono-color

digital bargraph with four fully

programmable set points for J, K, R, and

T type thermocouples and RTD inputs.

• Thermocouple (J, K, R and T types) or RTD (Pt-100. 385

and 392 curves. 3 wire/4wire). Digitally Linearized.

• Optional isolated 16 bit analog output. User or factory scal-

able to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any

desired digital span from ± one count to the full scale range

of – 1999 to 9999 (12000 counts).

• A Programmable Tricolor (Red-Green-Orange) or mono

color (red or green), 101 segment high brightness bargraph.

Vertical or optional horizontal format.

• Red 4-digit LED display with a range of -1999 to 9999

(12000 counts). Optional green digital display.

• Front panel LED annunciators provide indication of setpoint status.

•

Two 10 Amp Form C, and two 5 Amp Form A relays available

• Auto-sensing AC/DC power supply. For voltages between

85-265 V AC / 95-370 V DC (PS1) or 18-48 V AC / 10-72 V

DC (PS2).

• 24 V DC excitation is available to power external 4/20mA

transmitters and 5 or 10 V DC excitation is available for

resistance bridge type sensors.

• Provision to connect an external programming lockout switch.

• Provision for external DIM switch to reduce the brightest

display setting by 50%.

• Optional NEMA-4 front cover.

• Automatic intelligent averaging, smooths noisy signals while

providing a fast display response to real level changes.

Input Specs: ..............Depends on Input signal conditioner

A/D Converter:...........14 bit single slope

Accuracy:...................±(0.05% of reading + 2 counts)

Temp. Coeff.:.............100 ppm/°C (Typical)

Warm up time:...........2 minutes

Conversion Rate: ......10 conversions per second (Typical)

Digital Display:..........

4 digit 0.31" LED red (std), green (optn)

Range

–1999 to 9999 counts.

Bargraph Display:.....

101 segment 4” red vertical (std),

green or tricolor (optn), horizontal (optn)

Polarity:......................Assumed positive. Displays – negative

Decimal Selection:....Front panel button selectable, X•X•X•X•

Positive Overrange:..Bargraph and top segments of digital

display flash.

Negative Overrange:.First segment of bargraph and bottom

segments of digital display flash.

Relay Output: ............Two 5 Amp Form A relays and Two

10 Amp Form C relays.

Analog Output:..........Isolated 16 bit user scalable mA or V

OIC (mA out)...........

4-20 mA @ 0 to 500Ωmax loop resistance

OIV (volts out).......... 0-10 V DC @ 500 Ωor higher resistance

Power Supply:...........AC/DC Auto sensing wide range supply

PS1 (std) ................

85-265 VAC / 95-370 VDC @ 2.5W max 4.2W

PS2 .........................

18-48 VAC / 10-72 VDC @ 2.5W max 4.2W

Operating Temp.:.......0 to 60°C

Storage Temp: ...........–20°C to 70°C

Relative Humidity: ....95% (non condensing)

Case Dimensions:.....

9/64 DIN (Bezel 36Wx144Hmm)

Depth behind bezel (5.83") 148mm

Plus (0.7”) 18mm for connectors

Weight:.......................9.5 oz., 12 oz when packed

General Features Input Module Compatibility

Specifications

Index

LEOPARD FAMILY

FL-B101D40H

Leopard Bargraph Temperature Meter

101 Segment, 4 Digit 0.32” LEDs

in a 9/64 DIN CASE

• The bargraph can display, full

scale, any desired portion of

the digital reading.

•

Bargraph center zero function.

•

Four programmable setpoints.

• Setpoint 1 has delay-on-

make and delay-on-break

plus a special “pump on

pump off” mode that creates

a Hysteresis Band between

Software Features

SP1 and SP2.

• Relay activation can be

selected to occur above (hi)

or below (Lo) each setpoint.

• Digital display blanking.

• Decimal point setting.

• Four-level brightness control

of the bargraph and digital

display.

Bargraph Center Point Display Mode Selection. . 6

Bargraph Color Programming Mode . . . . . . . . 9

CaseDimensions...................... 13

ComponentLayout..................... 11

Connector Pinouts . . . . . . . . . . . . . . . . . . . . . 10

Connectors........................... 11

Controls and Indicators . . . . . . . . . . . . . . . . . . 2

Custom Faceplates and Scales . . . . . . . . . . . 15

Decimal Point and Brightness Selection . . . . . 5

Programming Conventions . . . . . . . . . . . . . . . . 2

Setpoint Setting & Relay Configuration Mode . . 8-9

SoftwareFeatures ...................... 1

Software Logic Tree . . . . . . . . . . . . . . . . . . . . . 3

Specifications.......................... 1

Standard Faceplates and Scales . . . . . . . . . . 14

Two Point Analog Output Range Setting & Cal. . 7

Thermocouple and RTD Type Selection Mode . . 4

Digital Span Selection for Display . . . . . . . . . . 5

Digital Span Selection for Analog Range Output . 6

Functional Diagram . . . . . . . . . . . . . . . . . . . . 10

GeneralFeatures....................... 1

Lockable NEMA Splash Proof Case. . . . . . . . 13

I-Series Input Signal Conditioning Modules . . 12

Input Module Calibration Procedures. . . . . . . 12

Ordering Information . . . . . . . . . . . . . . . . . . . 16

PinDescriptions....................... 10

LEOPARD

There are 3 different Plug-in Modular Input Signal

Conditioners for this specialized temperature only

member of the Leopard Family. IT10 is for J, K, T

and R thermocouples. IT11 is for 3 wire/4 wire Pt-

100 RTD inputs. IT15 is for 3 wire/4 wire Pt-1000

RTD inputs.

Version 2

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 2 May-29-2009 FL-B101D40H DS (FL8)

Front Panel Buttons

Program Button

The button is used to move from one program step to the next.

When pressed at the same time as the button, it initiates the

calibration mode. When pressed at the same time as the

button, it initiates the setpoint setting mode.

Button

DOWN

Button

PROGRAM

Button

LED

Annunciators

for Setpoints

1-4

Seven Segment

LED Display

101 Segment

Bargraph

Up Button

When in the operational display, pressing the button allows you

to view the setting of the saved Peak and Valley Values.

When setting a displayed parameter during programming, the

button is used to increase the value of the displayed parameter.

Down Button

When in the operational display, pressing the button allows you

to change the Brightness Level as well as to view the setting of

the setpoints SP1, SP2, SP3 & SP4.

When setting a displayed parameter during programming, the

button is used to decrease the value of the displayed parameter.

Front Panel LED Display

Annunciator LEDs

The annunciator LEDs indicate the alarm status. They are labeled

from bottom to top: SP1, SP2, SP3, SP4.

Digital LED Displays

The digital LED displays are used to display the meter input

signal readings. They also display the programming settings

during programming.

Setpoint Indication

The position of setpoints on the bargraph display are indicated by

an ON or OFF segment dependent on the bargraph display being

above or below the setpoint.

Setpoints

indicated

by an ON

Segment

Setpoints

indicated

by an OFF

Segment--

Controls and Indicators

This symbol represents the

OPERATIONAL DISPLAY.

This is the PROGRAM button.

This is the UP button.

This is the DOWN button.

When a button is shown, press and release

it to go onto the next step in the direction

indicated by the arrow. When an alterna-

tive dotted line is shown, this indicates that

an alternative logic branch will be followed

when a particular option is present.

When two buttons are shown side by

side and enclosed by a dotted line, they

must be pressed at the same time then

released to go onto the next programming

step.

If an X appears through a digit, it means

that any number displayed in that digit is not

relevant to the function being explained.

When the

and

buttons are shown

together, the display value can be increased

by pressing and releasing the

button

or decreased by pressing and releasing the

button.

When the

and

buttons are shown

with two displays, either display can be

selected by pressing and releasing the

buttons.

When two displays are shown together

with bursts, this indicates that the display is

toggling (flashing) between the name of the

function and the value.

Text or numbers shown between square

brackets in a procedure indicate the pro-

gramming code name of the function or the

value displayed on the meter display.

When there are more than two display selec-

tions they are shown in brackets below the

first display and are also selectable by press-

ing and releasing the

buttons.

A dotted line enclosing an entire logic dia-

gram indicates that programming branch

will appear only when a particular option is

present.

To explain software programming procedures, logic diagrams are

used to visually assist in following the programming steps. The

following symbols are used throughout the logic diagrams to

represent the buttons and indicators on the meter:

Programming Conventions

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comMay-29-2009 FL-B101D40H DS (FL8) Page 3

The FL-B101D40H is an intelligent bargraph meter with a hierarchi-

cal software structure designed for easy programming and opera-

tion, as shown below in the software logic tree.

Software Logic Tree

Software Version is Displayed on Power-up

When power is applied, all segments of the bargraph and digi-

tal display light up for 3 seconds. The version number of the

installed software is then displayed for 2 seconds, after which,

the operational display indicates the input signal.

15 Second Program Timeout

Except for ZERO and SPAN settings in the Two Point Digital Calibration Mode and the Analog Output Range Setting and Calibration Mode (cLo and

chi), the meter has a 15 second program timeout. If no buttons are pressed for 15 seconds in any of the other programming sequences, the meter will

exit the programming mode and return to the operational display. Any program changes that were made prior to pressing the button in the preced-

ing step will not be saved.

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 4 May-29-2009 FL-B101D40H DS (FL8)

STEP A Enter the Calibration Mode

Press the and buttons at the same time. Display

toggles between [CAL] and [oFF].

2) Press the or button. Display changes from [oFF] to [on].

3) Press the button.

STEP B If the Display toggles between [CAL] and [out] the optional Analog

Output hardware is installed. In which case select [CAL] [out].

Display toggles between [thEr] or [rtd] depending on whether a

IT10 Thermocouple Input Module or a IT11 RTD Input Module

are detected by the soft ware. If no optional output hardware is

installed the menu will skip directly to STEP C.

STEP C Sensor Type Selection

1) Using the and buttons, adjust the display to the

desired sensor type.

2) Press the button. Display toggles between [rES] reso-

lution select and previous [rES] setting.

STEP D Set the Resolution

1) Using the and buttons, adjust the display to the

desired resolution [rES] value.

Press the button.

Display toggles between [dEG] and

previous [dEG] selection.

STEP E Selection of Degree C or Degree F

1) Using the and buttons, adjust the display to either ˚C

or ˚F.

2) Press the button.

Calibration Procedure

Thermocouple type or RTD type selection mode

Input Module Calibration Procedure

See page 12 for the Calibration instructions of each Input Module type.

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comMay-29-2009 FL-B101D40H DS (FL8) Page 5

STEP A Enter the Calibration Sub Menu Mode

1) Press the and buttons at the same time. Display toggles

between [CAL] and [oFF].

2) Press the button. Display toggles between [bhi] and the

previous setting.

STEP B Set the Digital Span of the Bargraph Display (See example above)

1) Using the and buttons, adjust the display to the desired

high parameter reading, e.g. 6000 counts.

2) Press the button. Display toggles between [bLo] and the

previous setting.

3) Using the and buttons, adjust the display to the desired

low parameter reading, e.g. 4000 counts.

4) Press the button. Display changes from [4000] to [dP].

Digital Span Selection For Bargraph Display

Brightness Selection

Bargraph does not light up for

Input Signals up to 3999 counts

Bargraph lights up for Input

Signals above 4000 counts

Example of Setting the Digital Span of the Bargraph Display

to be Different than the Digital Display Range

The bargraph can be set to display full scale (0-101 bars) any portion

of the digital reading from a minimum of 100 counts to a maximum of

12,000 counts. This provides higher resolution bargraph indication for

those applications where the normal operating input signal range is less

than the desired full scale display range of the digital display.

For Example:

If the full scale range of the meter has been set from -1999 to

9999 (0-12,000 counts), but the normal operating range of the

input signal is between 4000 & 6000. The bargraph high param-

eter [bhi] can be set to 6000 and the bargraph low parameter [bLo]

can be set to 4000.

This means that although the meter could digitally display a signal

from -1999 to 9999 (0-12,000 counts), the bargraph display only

begins to function at a reading of 4000, and reaches full scale

indication at a reading of 6000. Although the digital display will

continue reading up to 9999 before indicating overrange, the bar-

graph display will indicate its overrange by flashing for readings

above 6000.

STEP C Press the

button. Display toggles between [br] and the

previous brightness setting.

Set the Bargraph and Digital Display Brightness

1) Using the and buttons, adjust the display to the desired

brightness setting (4 is the brightest setting).

2) Press the

button. Display toggles between [Anhi] and the

previous [Anhi] setting.

Note: If at this point, the display skips directly to STEP G and toggles

between [Cto] and [oFF], the software is detecting that the optional analog

output hardware is NOT installed.

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 6 May-29-2009 FL-B101D40H DS (FL8)

Example of Using the Center Point Bargraph Display Mode

with a Unipolar Input

If the meter's full scale range is set to 5000 counts, the midpoint would be

2500 counts. If a signal of 2500 counts is applied only one segment at the

2500 count mark will light up. If a signal of 4000 counts is applied the seg-

ments between the center segment (2500 counts) and the 4000 count mark

light up.

If a signal of 1000 counts is applied, the segments between the center seg-

ment (2500 counts) and the 1000 count mark will light up.

Example of Using the Center Point Bargraph Display Mode

with Bipolar Signal Inputs

The meter may also be calibrated to display symmetrical bipolar signals such

as ± 1 V or ± 10 V. When the center point display mode is selected, it will then

function as a center zero meter. When positive signals are applied, the bar

will go up from the center point, and when negative signals are applied, the

bar will go down from the center point.

STEP D Selecting the [Anhi] Digital Value for Analog High Output

1) Using the and buttons, adjust the display to the desired

digital value at which the [chi] Calibrated Analog High output will

occur. For digital readings outside the digital span selected, the

analog output will linearly rise above the value set for chi, up to the

maximum analog output capability. However, the analog output will

not go lower than the calibrated value set for cLo (see below).

2) Press the button.

Display toggles between [AnLo] and previous

[AnLo] setting.

STEP E Selecting the [AnLo] Digital Value for Analog Low Output

1) Using the and buttons, adjust the display to the desired

digital value at which the [cLo] Calibrated Analog Low output will

occur. For Digital readings outside the Digital Span selected, the

analog output will not go lower than the calibrated value set for cLo.

2) Press the button. The display toggles between [cto] and [oFF].

Note: Any two digital span points from –1999 to 9999 can be selected. The digital

values for [Anhi] analog high and [AnLo] analog low can be reversed to provide a 20 to

4mA output. The digital span selected can be as small as two counts, when using the

analog output to function as a Control or Alarm Driver. Small digital spans will cause

the high resolution 16 bit D to A to increment digitally in stair case steps.

See Two Point Analog Output Range Setting and Calibration at the top of the next page.

Digital Span Selection for Analog Range OutputDigital Span Selection for Analog Range Output

Bargraph Center Point Display Mode Selection

STEP F

Bargraph Center Point Mode Selection (See example above)

1) To select bargraph center point mode, press the or

button. Display changes from [oFF] to [on].

2) Press the button. Display toggles between [diSP] and [on]

or [oFF].

STEP G Digital Display ON/OFF Selection

1) To set the display to [oFF], press the or button. Display

toggles between [diSP] and [oFF].

2) Press the button. The display exits the calibration mode

and returns to the operational display. Only the bargraph

display is on and the digital display is off.

If the digital display is selected to be off, pressing any button to

make programming changes or to view setpoints activates the digital display.

When the procedure is complete, the digital display will then automatically

switch off.

The Display/Bargraph settings are now complete.

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comMay-29-2009 FL-B101D40H DS (FL8) Page 7

Determine if the Analog Output Selection Header is in the 4 to 20mA (0-

20mA) position or the 0 to 10VDC position. If necessary, the module may

have to be removed and the header position changed (see Component

Layout below).

Note: Always disconnect power from the meter before removing the ana-

log output module to adjust the mA or Volts output selection header and

reinstalling it. When power is reconnected, the meter’s software will auto-

matically detect the presence or absence of the analog output module.

STEP A Enter the Calibration Mode

Press the and buttons at the same time. Display

toggles between [cAL] and [oFF].

Press the or button. Display changes from [oFF] to [on].

Press the button. Display toggles between [cAL] and

[out] input calibration.

Note: If at this point the display skips directly to toggle between Zero and

the previous Zero setting, the software is detecting that the optional ana-

log output hardware is NOT installed.

STEP B Enter theTwo Point Analog [ouT] Output Range Setting and

Calibration Mode

Press the button. Display toggles between [cLo] and an

internal scale factor.

STEP E Set or Calibrate [cLo] the Low Analog Value of the

Analog Output Range

Connect a multimeter to analog output pins 17 and 18 (see

Rear Panel Pinouts on page 10). Using the and buttons,

adjust the analog output to the desired low value as measured

on the multimeter. cLo may be adjusted to any value from –0.3

mA to 18 mA (mA output selected) or from –0.6 V to 8 V (volt

output selected). However, the output of cLo must always be

less than the value selected for chi. If a reversed analog output

is desired, the values selected to establish the Digital Span can

be reversed (see top of page 6). For digital readings outside the

Digital Span selected, the analog output will not go any lower

than the calibrated value set for cLo. However, the analog out-

put will linearly rise above the value set for chi, up to the the

maximum analog output capability (see chi below).

Press the button. Display toggles between [chi] and an

internal scale factor.

STEP F Set or Calibrate [chi] the High Analog Value of the

Analog Output Range

1) Using the and buttons, adjust the analog output to

the desired high value as measured on the multimeter dis-

play. chi may be adjusted to any value from 18 mA to 24 mA

(mA output) or from 8 V to 10.3 V (volt output). However, the

value must be higher than the value selected for cLo. For

digital readings outside the Digital Span selected, the ana-

log output will linearly rise above the value set for chi, up to

the maximum analog output capability.

2) Press the button. The meter exits the calibration

mode and returns to the operational display.

Note: The analog output range established by the values selected for

cLo and chi will occur, automatically scaled, between the two digital

values selected for AnHi and AnLo. However, the analog output can

linearly rise above the chi value set for digital readings outside the

digital span selected. See Digital Span Selection on page 6.

Two Point Analog Output Range Setting and CalibrationTwo Point Analog Output Range Setting and Calibration

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 8 May-29-2009 FL-B101D40H DS (FL8)

The following programming steps are required to enter the setpoint values and configure the relay functions

in a meter with four relays using four setpoints. Generally if less than four relays are installed, the setpoints

without relays are operational in software for tri-color control or display only purposes. To remove unwanted

setpoint indications, set them to 9999 or -1999 depending on the relay activation mode selected.

STEP A Enter the Setpoint Mode

1) Press the and buttons at the same time. Display toggles between [SP1] and the previous SP1 setting.

STEP B Set Setpoint 1 [SP1]

1) Using the and buttons, adjust the display to the desired SP1 value.

2) Press the button. Display toggles between [doM] and the previous [doM] setting.

STEP C Set the SP1 Delay-on-Make [doM] Delay Time Setting

Using the and buttons, adjust the display to the desired [doM] value (0 to 9999 seconds).

The reading must continuously remain in an alarm condition until this delay time has elapsed before

the relay will make contact (energize).

2) Press the button. Display toggles between [dob] and the previous [dob] setting.

STEP D Set the SP1 Delay-on-Break [dob] Delay Time Setting

Using the and buttons, adjust the display to the desired [dob] value (0 to 9999 seconds).

The reading must continuously remain in a non-alarm condition until this delay time has elapsed

before the relay will break contact (de-energize).

2) Press the button. Display toggles between [hYSt] and the previous [hYSt] setting.

STEP E Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the button. Display toggles between PUM and (on) or (oFF).

STEP F Select Pump [PUM] (on) or (oFF)

Using the and buttons, select the Pump to be ON or OFF. When PUM is selected ON, and

SP2 is set at a value higher than SP1, the SP1 relay will operate in a special "pump on pump off" mode.

SP2 acts as the upper limit and SP1 acts as the lower limit of the Hysteresis Band on the SP1 relay.

For filling applications:

[rLYS] should be set to [LhXX] (see step M). The SP1 relay and SP1 LED Annunciator will then activate for inputs

less than the SP1 setpoint, and remain ON until the SP2 setpoint is reached.

For emptying applications:

[rLYS] should be set to [hhXX] (see step M). The SP1 relay and SP1 LED Annunciator will then activate for inputs

greater than the SP2 setpoint, and remain ON until the SP1 setpoint is reached.

2) Press the button. Display toggles between [SP2] and the previous SP2 setting.

STEP G Set Setpoint 2 (SP2)

1) Using the and buttons, adjust the display to the desired SP2 value.

2) Press the button. Display toggles between [hySt] and the previous [hySt] setting.

STEP H Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the button. Display toggles between [SP3] and the previous [SP3] setting.

STEP I Set Setpoint 3 (SP3) (No [doM] or [dob])

1) Using the and buttons, adjust the display to the desired SP3 value.

2) Press the button. Display toggles between [hySt] and the previous [hySt] setting.

STEP J Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the button. Display toggles between [SP4] and the previous [SP4] setting.

STEP K Set Setpoint 4 (SP4) (No [doM] or [dob])

Using the and buttons, adjust the display to the desired SP4 value.

2) Press the button. Display toggles between [hySt] and the previous [hySt] setting.

STEP L Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the button. Display toggles between [rLYS] and the previous relay setting.

Please Continue On Next Page.

Setpoint Setting and Relay Configuration Mode

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comMay-29-2009 FL-B101D40H DS (FL8) Page 9

To comply with the latest safety requirements, the tri-color bargraph is designed like a traffic light, to

display either red, orange or green, but only one color at a time. When the bar reaches a selected

color change point, the entire bar will change to the color designated for that zone. This eliminates any

ambiguity as to the signal status, especially just after transitioning to a new zone.

First (Step Q) is to select the color to be displayed, when the bar is “below*”, whichever set point is set

to the lowest position.

Second (Steps R, S, T, and U) is to select the color to be displayed when the bar is above each specific

set point, regardless of the order or position to which the set points are set.

However, if two or more setpoints with differently specified colors are positioned at the same set point

value, the color specified for the set point with the highest identifying number will be displayed. When set

points are set to the same value, the SP4 color overrides the SP3 color, the SP3 color overrides the SP2

color, and the SP2 color overrides the SP1 color.

STEP Q Select Bargraph Color when the bar is BELOW* the Setpoint that is set to the lowest

position