Texmate CL-B101D40RPM Manual de usuario

Page 1

CL-B101D40RPM(d0097) manual

• ThismeterhasbeendesignedspecificallyforRPMmeasurements.

JustenterthepulesperrevolutionandtheCL-B01DRPMbargraph

willcalculateanddisplaytheRPMreading.

• Three ranges with resolution of 0.1 RPM, 1 RPM and 10 RPM

(99.99x1000rpmmax).

• Optionalisolated16bitanalogoutput.Userorfactoryscalable

to4to20mA,0to20mAor0to10Vacrossanydesireddigital

spanfrom±onecounttothefullscalerangeof0to9999.

• Standard101segmentRedBarandRed4-digitLEDdisplaywith

arangeof0to9999.OptionalGreenBarandGreenDigitaldis-

play.AlsoOptionalProgrammableTricolor(Red-Green-Orange)

Barisavailable.

• FrontpanelLEDannunciatorsprovideindicationofsetpointstatus.

•

Two 9 Amp Form C, and two 4 Amp Form A or 4 x 4 Amp Form A

relays available

• Provisiontoconnectanexternalprogramminglockoutswitch.

• ProvisionforexternalDIMswitchtoreducethebrightest

displaysettingby50%.

• Automaticintelligentaveraging,smoothsnoisysignalswhile

providingafastdisplayresponsetoreallevelchanges.

• 24Vexcitationisavailabletopowerencodersorproxswitches.

General Features

Specifications

Index

Software Features

Bargraph Center Point Display Mode Selection ... 6

Bargraph Color Programming Mode ........ 9

Case Dimensions ....................... 7

Component Layout..................... 10

Connector Pinouts and Pin Descriptions..10-11

Controls and Indicators .................. 2

Setpoint Setting & Relay Configuration Mode....8-9

Software Features ...................... 1

Software Logic Tree ..................... 3

Specifications.......................... 1

Two Point Analog Output Range Calibration ..... 7

Digital Span Selection for Bargraph Display .. 5

Digital Span Selection for Analog Range Output... 6

General Features ....................... 1

I-Series Input Signal Conditioning Modules ..... 11

Ordering Information ................... 13

Programming Conventions................ 2

Input Specs:.................. DependsonInputsignalconditioner

A/D Converter:.............. 14bitsingleslope

Accuracy:...................... ±(0.05%ofreading+2counts)

Temp. Coeff.:................. 100ppm/°C(Typical)

Warm up time:............... 2minutes

Conversion Rate:.......... 10conversionspersecond(Typical)

Digital Display:..............

4 digit 0.56" LED red (std),green(optn)

Range

0to9999counts.



Bargraph Display:.........

101 segment 235º circular bar red (std),

green(optn)ortricolor(optn),

Polarity:......................... Assumedpositive.Displays–negative

Decimal Selection:........ Frontpanelbuttonselectable,X•X•X•X•

Positive Overrange:...... Bargraphandtopsegmentsofdigitaldisplay

flash.

Negative Overrange:.... Firstsegmentofbargraphandbottomseg-

mentsofdigitaldisplayflash.

Relay Output:................ Two9AmpFormCrelays,two4AmpForm

Arelaysor

4 x 4 Amp Form A relays.

Analog Output:............. Isolated16bituserscalablemAorV

 OIC(mAout)..............

4-20mA@0to500Ωmaxloopresistance

 OIV(voltsout).............. 0-10VDC@500Ωorhigherresistance

Power Supply:............... AC/DCAutosensingwiderangesupply

PS1 (std)....................

85-265 VAC / 95-300 VDC, 50-400Hz 4.2W

 PS2.............................

18-48VAC/10-72VDC,50-400Hz4.2W

Operating Temp.:.......... 0to50°C

Storage Temp:............... –20°Cto70°C

Relative Humidity:........ 95%(noncondensing)

Case Dimensions:........

Bezel(4.48"x4.48")113.8x113.8mm

Depthbehindbezel(4.23")107.46mm

Plus(0.48”)12.24mmforconnectors

Weight:........................... 16oz.,1lb4ozwhenpacked

CL-B101D40RPM

Smart 101 segment, 4 digit LED Tricolor or

Mono-color digital bargraph controller

with four fully programmable set points

in a switchboard style case for

RPM Measurement.

0.56”

LEDs

LEOPARD

FAMILY

• Thebargraphcandisplay,full

scale,anydesiredportionof

thedigitalreading.

• Setpoint1hasdelay-on-make

anddelay-on-breakplus

aspecial“pumponpump

off”modethatcreatesa

HysteresisBandbetweenSP1

andSP2.

• Fourprogrammablesetpoints

withadjustableHysteresis.•

Bargraphcenterzerofunction.

• Relayactivationcanbeselect-

edtooccurabove(hi)orbelow

(Lo)eachsetpoint.

• Decimalpointsetting.

• Digitaldisplayblanking.

• Four-levelbrightnesscontrol

Page 2

CL-B101D40RPM(d0097) manual

Controls and Indicators

This symbol represents the

OPERATIONAL DISPLAY.

This is the PROGRAM button.

This is the UP button.

This is the DOWN button.

When a button is shown, press and

release it to go onto the next step in the

direction indicated by the arrow. When

an alternative dotted line is shown, this

indicates that an alternative logic branch

will be followed when a particular option

is present.

When two buttons are shown side by side

and enclosed by a dotted line, they must

be pressed at the same time then released

to go onto the next programming step.

If an X appears through a digit, it means that

any number displayed in that digit is not rel-

evant to the function being explained.

[Span]

[10000]

When the

and

buttons are shown

together, the display value can be increased

by pressing and releasing the

button

or decreased by pressing and releasing the

button.

When the

and

buttons are shown

with two displays, either display can be

selected by pressing and releasing the

buttons.

When two displays are shown together

with bursts, this indicates that the display is

toggling (flashing) between the name of the

function and the value.

Text or numbers shown between square

brackets in a procedure indicate the pro-

gramming code name of the function or the

value displayed on the meter display.

When there are more than two display selec-

tions they are shown in brackets below the

first display and are also selectable by

pressing and releasing the

buttons.

A dotted line enclosing an entire logic dia-

gram indicates that programming branch

will appear only when a particular option is

present.

To explain software programming procedures, logic diagrams are

used to visually assist in following the programming steps. The

following symbols are used throughout the logic diagrams to

represent the buttons and indicators on the meter:

Programming Conventions

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

Front Panel Buttons

Program Button

The

button is used to move from one program step to the next.

When pressed at the same time as the button, it initiates the

calibration mode. When pressed at the same time as the but-

ton, it initiates the setpoint setting mode.

101 Segment

Bargraph

Up Button

When in the operational display, pressing the button allows you

to view the setting of the saved Peak and Valley Values.

When setting a displayed parameter during programming, the

button is used to increase the value of the displayed parameter.

Down Button

When in the operational display, pressing the button allows you

to change the Brightness Level as well as to view the setting of

the setpoints SP1, SP2, SP3 & SP4.

When setting a displayed parameter during programming, the

button is used to decrease the value of the displayed parameter.

Front Panel LED Display

Annunciator LEDs

The annunciator LEDs indicate the alarm status. They are labeled

from bottom to top: SP1, SP2, SP3, SP4.

Digital LED Displays

The digital LED displays are used to display the meter input

signal readings. They also display the programming settings

during programming.

Setpoint Indication

The position of setpoints on the bargraph display are indicated by

an ON or OFF segment dependent on the bargraph display being

above or below the setpoint.

Setpoints

indicated

by an ON

Segment

Setpoints indicated

by an OFF Segment

Front Panel Controls and Indicators

LED

Annunciators

for Setpoints

1-4

Single or

Tri-color

Bargraaph

Display

Button

DOWN

Button

PROGRAM

Button

7 Segments

Digital

Display

Page 3

CL-B101D40RPM(d0097) manual

The CL-B101D40RPM is an intelligent bargraph meter with a hier-

archical software structure designed for easy programming and

operation, as shown below in the software logic tree.

Software Logic Tree

Peak

[PEAK]

Reset

PEAK

Reset

VALY

Valley

[VALY]

[orAn]

[rEd]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

See Page 9

Tricolor Bargraph

The tri-color bargraph is

designed like a traffic light, to

display either red, orange or

green, but only one color at a

time. The color to be displayed

is selected in two ways.

The first step is to select the

color to be displayed when the

bar is “below” whichever set

point is set to the lowest

position.

The second step is to select the

color to be displayed when the

bar is above each specific

setpoint, regardless of the order

or position to which the set

points are set.

However, if two or more

setpoints with differently

specified colors are positioned

at the same set point value, the

color specified for the set point

with the highest identifying

number will be displayed. When

setpoints are set to the same

value, the SP4 color overrides

the SP3 color, the SP3 color

overrides the SP2 color, and the

SP2 color overrides the SP1

color.

Set Setpoint 1

[SP1]

Delay-on-Make

[doM]

Delay-on-Break

[dob]

Relays

Activation

[rLYS]

(h) High the

relay

energizes

when the

setpoint is

exceeded.

(L) Low

the relay

energizes

below the

setpoint.

Setpoint 2

[SP2]

Setpoint 2

[SP2]

Setpoint 1

[SP1]

Setpoint 3

[SP3]

NOTE: [dom] [dob]

Functions are only

available for SP1

abd SP3

0 to 9999

seconds

0 to 9999

seconds

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Bar Color

[coL]

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Setpoint 3

[SP3]

Setpoint 4

[SP4]

Setpoint 4

[SP4]

Operational Display

MAIN MENU

PEAK & VALLEY

VIEW & RESET

BRIGHTNESS AND

SETPOINT VIEW MODE

Bargraph Center Point

Display Selection [cto]

This branch will

only appear if

the analog

output option

is installed

Back to

Operational

Display

Digital Display

ON/OFF

Selection [diSP]

Sub-menu MODE

Calibration Mode

Calibration

Input

Calibration

Output

Calibrate Analog

Output Low

[cLo]

Calibrate Analog

Output High

[chi]

Select the Digital

Reading at which

the Analog Output

Hi [chi] will occur

Select the Digital

Reading at which

the Analog Output

Lo [cLo] will occur

This branch will only appear

if the analog output option

is installed

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

See Page 6

DIGITAL DISPLAY ON/OFF

See Page 6

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

See Page 6

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

See Page 7

Bargraph Display

Scale Lo Range

Setting [bLo]

Bargraph Display

Scale hi Range

Setting [bhi]

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

See Page 5

Goes directly

to Zero setting

if Analog Output

is not installed

PULSES PER

REVOLUTION, RANGE

SELECTION

–

4.00

–

20.00

1 Dimmest

2 Dim

3 Bright

4 Brightest

SETPOINT SETTING AND

RELAY CONFIGURATION MODE

See Page 8

L or h

Display

Brightness

[br]

Delay-on-Make

[doM]

Delay-on-Break

[dob]

0 to 9999

seconds

0 to 9999

seconds

Sub-menu MODE

Software Version is Displayed on Power-up

When power is applied, all segments of the bargraph and dig-

ital display light up for 3 seconds. The version number of the

installed software is then displayed for 2 seconds, after which,

the operational display indicates the input signal.

15 Second Program Timeout

Except for ZERO and SPAN settings in the Two Point Digital Calibration Mode

and the Analog Output Range Setting and Calibration Mode (cLo and chi), the

meter has a 15 second program timeout. If no buttons are pressed for 15

seconds in any of the other programming sequences, the meter will exit the

programming mode and return to the operational display. Any program chang-

es that were made prior to pressing the

button in the preceding step will

not be saved.

Page 4

CL-B101D40RPM(d0097) manual

STEP A Enter the Calibration Mode

Press the

and buttons at the same time. Display tog-

gles between [CAL] and [oFF].

2) Press the or button. Display changes from [oFF] to

[on].

Press the

button. Display toggles between [CAL] and

[out].

Note: If at this point, the display skips directly to STEP C and toggles

between [SPAn] and the previous [SPan] setting, the software is

detecting that the optional analog output hardware is NOT installed.

STEP B

Select Pulese Per Revolution, Range Slection

1) Press the or button to select CAL

[iP] for Pulses Per

Revolution Slection.

2) Press the

button. Display toggles between [PPr] and

the previous Pulses Per Revolution setting.

STEP C Enter the Pulese Per Revolution (PPR)

1) Using the and buttons, enter the number of pulese

per revolution. Any number between 1 and 9999 may be

enterd.

2) Press the

button. Display toggles between [rg] and the

previous range setting.

STEP D Select the Range

1) Using the and buttons, selete the required range.

There are three ranges with resolutions of 0.1 (max. 999.9

RPM), 1 (max. 9999 RPM) and 10 RPM (max. 99.99 x 10000

RPM)

2) Press the

button.

Pulses Per Revolution and Range Selection

MAIN MENU

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

STEP C PPR

STEP D Range

To Digital Span Selection for

Bargraph Display Page 5

cAL out/iP branch will only

appear if the analog output

option is installed, otherwise

cAL on goes directly to ZEro

setting

PULSES PER

REVOLUTION, RANGE

SELECTION

To Digital Span Selection

for Bargraph Display

See Page 6

To Two Point Analog

Output Range Setting

and Calibration

See Page 7

[0.1]

[1]

[10]

Page 5

CL-B101D40RPM(d0097) manual

Example

From Pulses Per

Revolution, Range

Selection Mode

See Page 4

STEP A

STEP B

See Example Above

of Bargraph Display

Scale Range

To Digital Span Selection

for Analog Range Output or

Bargraph Center Point

Display Mode Selection

on Page 6

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

STEP A Enter the Calibration Sub Menu Mode

1) Press the

and buttons at the same time. Display toggles

between [CAL] and [oFF].

2) Press the

button. Display toggles between [bhi] and the

previous setting.

STEP B Set the Digital Span of the Bargraph Display

(See example

above)

1) Using the and buttons, adjust the display to the

desired high parameter reading, e.g. 6000 counts.

2) Press the

button. Display toggles between [bLo] and the

previous setting.

3) Using the and buttons, adjust the display to the

desired low parameter reading, e.g. 4000 counts.

4) Press the

button. Display changes from [4000] to [dP].

Note: If at this point, the display skips directly to STEP E and toggles

between [Cto] and [oFF], the software is detecting that the optional analog

output hardware is NOT installed.

Digital Span Selection For Bargraph Display

Bargraph does not light

up for Input Signals up to

3999 counts

Bargraph lights up for

Input Signals above

4000 counts

Bar

High

Bar

Low

Bar

High

Bar

Low

25 75

100

25 75

100

No bargraph display

Digital display

No bargraph display

Digital display

An example of setting the

digital span of the bargraph

display to be different than

the digital display range

The bargraph can be set to display full scale (0-101 bars) any portion

of the digital reading from a minimum of 100 counts to a maximum of

12,000 counts. This provides higher resolution bargraph indication for

those applications where the normal operating input signal range is less

than the desired full scale display range of the digital display.

For Example:

If the full scale range of the meter has been set from -1999 to

9999 (0-12,000 counts), but the normal operating range of the

input signal is between 4000 & 6000. The bargraph high parame-

ter [bhi] can be set to 6000 and the bargraph low parameter [bLo]

can be set to 4000.

This means that although the meter could digitally display a signal

from -1999 to 9999 (0-12,000 counts), the bargraph display only

begins to function at a reading of 4000, and reaches full scale

indication at a reading of 6000. Although the digital display will

continue reading up to 9999 before indicating overrange, the bar-

graph display will indicate its overrange by flashing for readings

above 6000.

Page 6

CL-B101D40RPM(d0097) manual

STEP C Selecting the [Anhi] Digital Value for Analog High Output

1) Using the and buttons, adjust the display to the desired

digital value at which the [chi] Calibrated Analog High output will

occur. For digital readings outside the digital span selected, the

analog output will linearly rise above the value set for chi, up to the

maximum analog output capability. However, the analog output will

not go lower than the calibrated value set for cLo (see below).

2) Press the

button. Display toggles between [AnLo] and

previous [AnLo] setting.

STEP D Selecting the [AnLo] Digital Value for Analog Low Output

1) Using the and buttons, adjust the display to the desired

digital value at which the [cLo] Calibrated Analog Low output will

occur. For Digital readings outside the Digital Span selected, the

analog output will not go lower than the calibrated value set for

cLo.

2) Press the

button. The display toggles between [cto] and

[oFF].

Note: Any two digital span points from –1999 to 9999 can be selected. The digital

values for [Anhi] analog high and [AnLo] analog low can be reversed to provide a 20 to

4mA output. The digital span selected can be as small as two counts, when using the

analog output to function as a Control or Alarm Driver. Small digital spans will cause

the high resolution 16 bit D to A to increment digitally in stair case steps.

Digital Span Selection for Analog Range OutputDigital Span Selection for Analog Range Output

Bargraph Center Point Display Mode Selection

STEP E

Bargraph Center Point Mode Selection (See example above)

1) To select bargraph center point mode, press the or

button. Display changes from [oFF] to [on].

2) Press the

button. Display toggles between [diSP] and

[on] or [oFF].

STEP F Digital Display ON/OFF Selection

1) To set the display to [oFF], press the or button.

Display toggles between [diSP] and [oFF].

2) Press the

button. The display exits the calibration mode

and returns to the operational display. Only the bargraph

display is on and the digital display is off.

If the digital display is selected to be off, pressing any button to

make programming changes or to view setpoints activates the digital display.

When the procedure is complete, the digital display will then automatically

switch off.

The Display/Bargraph settings are now complete.

Operational Display

STEP E

STEP F

See Example of Bargraph

Center Point Display Mode

Selection Above

From Digital Span Selection

for Analog Range Output Above

or Direct From Digital Span Selection

for Bargraph Display Page 5

if Analog Output Option is Not Present

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

STEP C

STEP D

This branch will only

appear if the analog

output option is installed

To Bargraph Center

Point Display Mode

Selection Below

From Digital Span

Selection for Bargraph

Display

See Page 5

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

Example of Using the Center Point Bargraph Display Mode

with a Unipolar Input

If the meter's full scale range is set to 5000 counts, the midpoint would

be 2500 counts. If a signal of 2500 counts is applied only one segment at

the 2500 count mark will light up. If a signal of 4000 counts is applied the

segments between the center segment (2500 counts) and the 4000 count

mark light up.

If a signal of 1000 counts is applied, the segments between the center seg-

ment (2500 counts) and the 1000 count mark will light up.

Example of Using the Center Point Bargraph Display Mode

with Bipolar Signal Inputs

The meter may also be calibrated to display symmetrical bipolar signals such

as ± 1 V or ± 10 V. When the center point display mode is selected, it will

then function as a center zero meter. When positive signals are applied, the

bar will go up from the center point, and when negative signals are applied,

the bar will go down from the center point.

-1V +1V

0.800

-0.800

-1V +1V

Center Point

Single Bar Lit

Center Point

As signal

increases

Digital display

Center Point

As signal

decreases

Digital display

05000

5000

2500

4000

5000

2500

1000

Center Point

Single Bar Lit

Center Point

As signal

increases

Digital display

Center Point

As signal

decreases

Digital display

Unipolar Signal Input Bipolar Signal Input

Page 7

CL-B101D40RPM(d0097) manual

Case Dimensions

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

STEP E

Calibrate

Analog

Output

STEP F

Calibrate

Analog

Output

Will only appear if the analog

output option is installed

To Digital Span Selection

for Bargraph Display

See Page 5

To Two Point Digital

Calibration Mode

See Page 4

Operational Display

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

–x

4.00

–x

20.00

Determine if the Analog Output Selection Header is in the 4 to 20mA (0-20mA) position or the 0

to 10VDC position. If necessary, the module may have to be removed and the header position

changed (see Component Layout below).

Note: Always disconnect power from the meter before removing the analog output module to

adjust the mA or Volts output selection header and reinstalling it. When power is reconnected, the

meter’s software will automatically detect the presence or absence of the analog output module.

STEP A Enter the Calibration Mode

1) Press the

and buttons at the same time. Display toggles between [cAL] and [oFF].

2) Press the or button. Display changes from [oFF] to [on].

3) Press the

button. Display toggles between [cAL] and [out] input calibration.

Note: If at this point the display skips directly to toggle between Zero and the previous Zero

setting, the software is detecting that the optional analog output hardware is NOT installed.

STEP B

Enter the Two Point Analog [ouT] Output Range Setting and Calibration Mode

1) Press the

button. Display toggles between [cLo] and an internal scale factor.

STEP E Set or Calibrate [cLo] the Low Analog Value of the Analog Output Range

1) Connect a multimeter to analog output pins 17 and 18 (see Rear Panel Pinouts

on page 10). Using the and buttons, adjust the analog output to the desired

low value as measured on the multimeter. cLo may be adjusted to any value from

–0.3 mA to 18 mA (mA output selected) or from –0.6 V to 8 V (volt output selected).

However, the output of cLo must always be less than the value selected for chi. If

a reversed analog output is desired, the values selected to establish the Digital

Span can be reversed (see top of page 6). For digital readings outside the Digital

Span selected, the analog output will not go any lower than the calibrated value set

for cLo. However, the analog output will linearly rise above the value set for chi, up

to the the maximum analog output capability (see chi below).

2) Press the

button. Display toggles between [chi] and an internal scale factor.

STEP F Set or Calibrate [chi] the High Analog Value of the Analog Output Range

1) Using the and buttons, adjust the analog output to the desired high value

as measured on the multimeter display. chi may be adjusted to any value from 18

mA to 24 mA (mA output) or from 8 V to 10.3 V (volt output). However, the value

must be higher than the value selected for cLo. For digital readings outside the

Digital Span selected, the analog output will linearly rise above the value set for chi,

up to the maximum analog output capability.

2) Press the

button. The meter exits the calibration mode and returns to the

operational display.

Note: The analog output range established by the values selected for cLo and chi will occur, auto-

matically scaled, between the two digital values selected for AnHi and AnLo. However,

the analog

output can linearly rise above the chi value set for digital readings outside the digital span

selected. See Digital Span Selection on page 6.

Two Point Analog Output Range Setting and CalibrationTwo Point Analog Output Range Setting and Calibration

101.60

4.000

42.85

1.687

42.85

1.687

42.85

1.687

42.85

1.687

6.50

0.256

113.79

4.480

113.79

4.480

56.90

2.240

56.90

2.240

17.50

0.689

97.77

3.849

119.70

4.713

13.70

0.539

1/4"-28UNF

Panel Cutout

5.0

0.197

0.157

16.30

0.642

13.70

0.539

4.80

0.189

screw-10-32 UNF

0.315

0.276

16.30

0.642

13.70

0.539

2.60

0.102

6.32

0.249

screw-1/4”-28 UNF

Page 8

CL-B101D40RPM(d0097) manual

Operational Display

SETPOINT SETTING

AND RELAY

CONFIGURATION MODE

STEP A

STEP B

STEP C

STEP D

STEP E

STEP F

STEP G

STEP H

STEP I

STEP J

STEP K

STEP L

STEP M

To Step N of Setpoint

Setting and Relay

Configuration Page 9

0 to 9999

seconds

0 to 9999

seconds

0 to 9999

seconds

0 to 9999

seconds

The following programming steps are required to enter the setpoint values and configure the relay functions

in a meter with four relays using four setpoints. Generally if less than four relays are installed, the setpoints

without relays are operational in software for tri-color control or display only purposes. To remove unwanted

setpoint indications, set them to 9999 or -1999 depending on the relay activation mode selected.

STEP A Enter the Setpoint Mode

1) Press the

and buttons at the same time. Display toggles between [SP1] and the previous

SP1 setting.

STEP B Set Setpoint 1 [SP1]

1) Using the and buttons, adjust the display to the desired SP1 value.

2) Press the

button. Display toggles between [doM] and the previous [doM] setting.

STEP C Set the SP1 Delay-on-Make [doM] Delay Time Setting

Using the and buttons, adjust the display to the desired [doM] value (0 to 9999 seconds).

The reading must continuously remain in an alarm condition until this delay time has elapsed before

the relay will make contact (energize).

2) Press the

button. Display toggles between [dob] and the previous [dob] setting.

STEP D Set the SP1 Delay-on-Break [dob] Delay Time Setting

Using the and buttons, adjust the display to the desired [dob] value (0 to 9999 seconds).

The reading must continuously remain in a non-alarm condition until this delay time has elapsed

before the relay will break contact (de-energize).

2) Press the

button. Display toggles between [hYSt] and the previous [hYSt] setting.

STEP E Set the Hysteresis [hYSt] Setting for Setpoint 1

Using the and buttons, adjust the display to the desired hysteresis [hYSt] value.

2) Press the

button. Display toggles between [SP2] and the previous [SP2] setting.

STEP F Set Setpoint 2 (SP2)

1) Using the and buttons, adjust the display to the desired SP2 value.

2) Press the

button. Display toggles between [hySt] and the previous [hySt] setting.

STEP G Set the Hysteresis [hYSt] Setting for Setpoint 2

1) Using the and buttons, adjust the display to the desired

hysteresis [hYSt] value

2) Press the

button. Display toggles between [SP3] and the previous [SP3] setting.

STEP H Set Setpoint 3 (SP3)

Using the and buttons,

adjust the display to the desired SP3 value

2) Press the

button. Display toggles between [SP3] and the previous [SP3] setting.

STEP I Set the SP3 Delay-on-Make [doM] Delay Time Setting

Using the and buttons, adjust the display to the desired [doM] value (0 to 9999 seconds).

The reading must continuously remain in an alarm condition until this delay time has elapsed before

the relay will make contact (energize).

2) Press the

button. Display toggles between [dob] and the previous [dob] setting.

STEP J Set the SP3 Delay-on-Break [dob] Delay Time Setting

Using the and buttons, adjust the display to the desired [dob] value (0 to 9999 seconds).

The reading must continuously remain in a non-alarm condition until this delay time has elapsed

before the relay will break contact (de-energize).

2) Press the

button. Display toggles between [hYSt] and the previous [hYSt] setting.

STEP K Set the Hysteresis [hYSt] Setting for Setpoint 3

Using the and buttons, adjust the display to the desired hysteresis [hYSt] value

2) Press the

button. Display toggles between [SP4] and the previous [SP4] setting.

STEP L Set Setpoint 4 (SP4)

Using the and buttons,

adjust the display to the desired SP4 value

2) Press the

button. Display toggles between [hySt] and the previous [hySt] setting.

STEP M Set the Hysteresis [hYSt] Setting for Setpoint 4

Using the and buttons, adjust the display to the desired hysteresis [hYSt] value

2) Press the

button. Display toggles between [rLYS] and the previous relay setting.

Please Continue On Next Page.

Setpoint Setting and Relay Configuration Mode

Page 9

CL-B101D40RPM(d0097) manual

STEP N

STEP O

STEP P

STEP Q

STEP R

STEP S

STEP T

STEP U

STEP V

[orAn]

[rEd]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

Operational Display

From From Step L of

Setpoint Setting and Relay

Configuration Page 8

L or h

To comply with the latest safety requirements, the tri-color bargraph is designed like a traffic light, to

display either red, orange or green, but only one color at a time. When the bar reaches a selected

color change point, the entire bar will change to the color designated for that zone. This eliminates any

ambiguity as to the signal status, especially just after transitioning to a new zone.

First (Step Q) is to select the color to be displayed, when the bar is “below*”, whichever set point is set

to the lowest position.

Second (Steps R, S, T, and U) is to select the color to be displayed when the bar is above each specific

set point, regardless of the order or position to which the set points are set.

However, if two or more setpoints with differently specified colors are positioned at the same set point

value, the color specified for the set point with the highest identifying number will be displayed. When

set points are set to the same value, the SP4 color overrides the SP3 color, the SP3 color overrides the

SP2 color, and the SP2 color overrides the SP1 color.

STEP Q Select Bargraph Color when the bar is BELOW* the Setpoint that is set to the lowest

position