Texas Instruments TPS25831-Q1 Manual de usuario

SLVUBL1A–November 2018–Revised February 2019

TPS25831-Q1 Evaluation Module

User's Guide

SLVUBL1A–November 2018–Revised February 2019

TPS25831-Q1 Evaluation Module

This user's guide describes the TPS25831-Q1 evaluation module (TPS25831Q1EVM-062). This document

contains the EVM schematics, EVM configuration, bill of materials (BOM), board layout drawing, and

assembly drawing.

Contents

1 Introduction ................................................................................................................... 2

2 Test Setup .................................................................................................................... 2

3 Board Layout ................................................................................................................. 5

4 Schematic and Bill of Materials........................................................................................... 11

List of Figures

1 EVM Setup For Testing Buck Converter ................................................................................. 2

2 EVM Setup for Charging USB Type-C™ Device ....................................................................... 3

3 Top Side Assembly.......................................................................................................... 5

4 Bottom Side Assembly...................................................................................................... 6

5 Top Layer Layout............................................................................................................ 7

6 Middle Layer 1 Layout ...................................................................................................... 8

7 Middle Layer 2 Layout ...................................................................................................... 9

8 Bottom Layer Layout....................................................................................................... 10

9 TPS25831Q1EVM-062 Schematic....................................................................................... 11

List of Tables

1 Connectors ................................................................................................................... 3

2 Jumpers....................................................................................................................... 3

3 LED............................................................................................................................ 3

4 Test Points.................................................................................................................... 4

5 Bill of Materials ............................................................................................................. 12

Trademarks

USB Type-C is a trademark of USB Implementers Forum.

Introduction

www.ti.com

2SLVUBL1A–November 2018–Revised February 2019

Submit Documentation Feedback

TPS25831-Q1 Evaluation Module

1 Introduction

The TPS25831Q1EVM-062 is an evaluation module (EVM) for TI's TPS25831-Q1 USB Type-C™ and

BC1.2 5-V, 3.5-A output, 36-V input synchronous buck with cable compensation. The EVM operates over

a range from 6 V to 36 V and provides USB Type-C connectors to evaluate BC1.2 and USB Type-C

charging and USB2.0 data communication functions. The value of cable compensation, current limit, and

switching frequency can be adjusted by resistors on the EVM.

1.1 Features

The following features are available on this EVM:

• 6-V to 36-V input range, 3.5-A continuous output current buck converter

• Forced PWM operation with spread-spectrum dithering

• Fully AEC-Q100 qualified

• ± 8% Current sense accuracy (IOUT > 1.5 A) for precision cable droop compensation

• USB battery charging specification Rev. 1.2 and USB Type-C Rev. 1.3 compliant

• CC1, CC2, D+ and D– Short-to-VBAT, and VBUS protection

• User-programmable VBUS current limit and internal VCONN current limiting

• External NTC component for thermal management

1.2 Applications

The EVM is used in the following applications:

• Automotive: Infotainment, USB hubs, aftermarket USB chargers

2 Test Setup

Figure 1 shows a typical test setup for testing the TPS25831Q1EVM-062 buck converter. Connect J2 to

the 13.5-V power supply. Connect the load to the J1 connector. Install a shunt on J4 to apply Rd on CC1.

Figure 1. EVM Setup For Testing Buck Converter

www.ti.com

Test Setup

SLVUBL1A–November 2018–Revised February 2019

TPS25831-Q1 Evaluation Module

Figure 2 shows a typical test setup for charging the USB Type-C device. Connect J2 to the 13.5-V power

supply. Connect USB Type-C device to J7 connector. Shunts do not need to be installed on J4 or J5.

Figure 2. EVM Setup for Charging USB Type-C™ Device

2.1 Physical Access

Table 1 lists the TPS25831Q1EVM-062 connector functionality, Table 2 describes the jumper

configuration, Table 3 shows LED labels and description, and Table 4 describes the test point availability.

Table 1. Connectors

Connector Component Type Description

J2 Terminal block Power input connector for TPS25831-Q1. Connect to a 6-V to 36-V power supply.

J1 Terminal block The regulated output voltage of the TPS25831-Q1 buck converter.

J3 USB Type-A connector, plug Upstream facing USB 2.0 Type A connector. Connect to the USB 2.0 host for data

pass through to J7. The power pin of this connector is float.

J7 USB Type-C connector,

receptacle Downstream facing USB Type-C connector. Connect to the USB Type-C slave for

data pass through from J3 and BC1.2 or USB Type-C identification. USB output

power is provided to the slave from the buck converter of the TPS25831-Q1

device.

Table 2. Jumpers

Jumper Label Description

J4 CC1 3 × 1 header. Install shunt to connect Ra or Rd on CC1. Remove shunt to float CC1.

J5 CC2 3 × 1 header. Install shunt to connect Ra or Rd on CC2. Remove shunt to float CC2.

J6 CTRL1 Install shunt to select CTRL1 as LOW. Remove shunt to select CTRL1 as HIGH.

CTRL2 Install shunt to select CTRL2 as LOW. Remove shunt to select CTRL2 as HIGH.

Table 3. LED

LED Label Description

D4 THERM_WARN THERM_WARN signal LED. Turn on when thermal warning asserts.

D5 LD_DET LD_DET signal LED. Turn on when LD_DET asserts.

D6 POL POL signal LED. Turn on when POL asserts.

D7 FAULT FAULT signal LED. Turn on when FAULT asserts.

Test Setup

www.ti.com

4SLVUBL1A–November 2018–Revised February 2019

Submit Documentation Feedback

TPS25831-Q1 Evaluation Module

Table 4. Test Points

Test Point Label Description

TP1 VCONN VCC pin test point via R1 or external Vconn input

TP2 CSP Test point of voltage between inductor and sense resistor.

TP3 CSN/OUT CSN pin test point and DC-DC output test point

TP4 VIN VIN pin test point

TP5 EN EN pin test point or external EN input.

TP6,TP7, TP8, TP9 GND Power ground test point

TP10 THERM_WARN Thermal warning pin test point

TP11 CC1 CC1 pin test point

TP12 CC2 CC2 pin test point

TP13 LD LD_DET pin test point

TP14 POL POL pin test point

TP15 FLT FAULT pin test point

TP16 VBUS USB Type-A and USB Type-C connector, VBUS test point

TP17 RT RT pin test point or external clock input.

2.2 Adjusting the Switching Frequency

If other frequencies are desired, within the frequency range of 400 kHz to 2.2 MHz, the Rtresistor (R11)

value can be changed. Consult the data sheet for proper selection of the Rtresistor (R11). Change the

inductor (L1) and the total output capacitance for proper control loop operation.

The RT/SYNC pin can also be used to synchronize the internal oscillator to an external clock. The

TPS25831EVMQ1-062 allows users to synchronize the internal oscillator to both Lo-Z clock source and

Hi-Z clock source by configuring R11, R12, and C13. Refer to the data sheet for detailed information.

2.3 Adjusting the Current Limit Value

If other current limit values are desired, the Rlresistor (R15) value can be changed. Consult the data

sheet for proper selection of the Rlresistor (R15).

2.4 Adjusting the Cable Compensation Value

If other cable compensation values are desired, the Rmresistor (R16) value can be changed. Consult the

data sheet for proper selection of the Rmresistor (R16).

2.5 Adjusting Thermal Management

If other thermal management desired, the RT1 resistor, R14, R18 and R19 value can be changed. Consult

the data sheet for proper selection .

www.ti.com

Board Layout

SLVUBL1A–November 2018–Revised February 2019

TPS25831-Q1 Evaluation Module

3 Board Layout

Figure 3 and Figure 4 show the top and bottom assembly. Figure 5 to Figure 8 show the layout of the

EVM.

Figure 3. Top Side Assembly

Board Layout

www.ti.com

6SLVUBL1A–November 2018–Revised February 2019

Submit Documentation Feedback

TPS25831-Q1 Evaluation Module

Figure 4. Bottom Side Assembly

www.ti.com

Board Layout

SLVUBL1A–November 2018–Revised February 2019

TPS25831-Q1 Evaluation Module

Figure 5. Top Layer Layout

Board Layout

www.ti.com

8SLVUBL1A–November 2018–Revised February 2019

Submit Documentation Feedback

TPS25831-Q1 Evaluation Module

Figure 6. Middle Layer 1 Layout

www.ti.com

Board Layout

SLVUBL1A–November 2018–Revised February 2019

TPS25831-Q1 Evaluation Module

Figure 7. Middle Layer 2 Layout

Board Layout

www.ti.com

10 SLVUBL1A–November 2018–Revised February 2019

Submit Documentation Feedback

TPS25831-Q1 Evaluation Module

Figure 8. Bottom Layer Layout

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments TPL7407L7 Manual de usuario

Texas Instruments

Texas Instruments TPS53515EVM-PWR587 Manual de usuario

Texas Instruments

Texas Instruments TCA8418 I2C Manual de usuario

Texas Instruments

Texas Instruments LMR33630EVM Manual de usuario

Texas Instruments

Texas Instruments TPSM8D6C24EVM-2V0 Manual de usuario

Texas Instruments

Texas Instruments SimpleLink CC2650F128RGZ Manual de usuario

Texas Instruments

Texas Instruments DRV2667EVM-CT Manual de usuario

Texas Instruments

Texas Instruments TPA6020A2 Manual de usuario

Texas Instruments

Texas Instruments TAS5514BQ1DKDEVM Manual de usuario

Texas Instruments

Texas Instruments TPS7H4002EVM-CVAL Manual de usuario

Texas Instruments

Texas Instruments TMS320DM6446 DVEVM v2.0 Manual de usuario

Texas Instruments

Texas Instruments BoosterPack AM2 BLDC Series Manual de usuario

Texas Instruments

Texas Instruments TLV841EVM Manual de usuario

Texas Instruments

Texas Instruments TPS25810EVM-745 Manual de usuario

Texas Instruments

Texas Instruments AMC1210EVM Manual de usuario

Texas Instruments

Texas Instruments Sitara AM572 Series Manual de usuario

Texas Instruments

Texas Instruments TMS320C3 Series Manual de usuario

Texas Instruments

Texas Instruments TLV840EVM Manual de usuario

Texas Instruments

Texas Instruments BQ240729 Manual de usuario

Texas Instruments

Texas Instruments TPS65084x EVM Manual de usuario

Texas Instruments

Texas Instruments TPA741 MSOP Manual de usuario

Texas Instruments

Texas Instruments Stellaris LM3S6965 Manual de usuario

Texas Instruments

Texas Instruments ADS1232REF Manual de usuario

Texas Instruments

Texas Instruments LMZM23601 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario