Texas Instruments SimpleLink Ethernet MSP432E401Y Manual de usuario

SLAU748B–October 2017–Revised September 2018

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

User's Guide

SLAU748B–October 2017–Revised September 2018

SimpleLink™ Ethernet MSP432E401Y Microcontroller

LaunchPad™ Development Kit (MSP-EXP432E401Y)

The SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™ Development Kit is a low-cost

evaluation platform for SimpleLink Arm®Cortex®-M4F-based Ethernet microcontrollers. The Ethernet

LaunchPad development kit highlights the MSP432E401Y microcontroller with its on-chip 10/100 Ethernet

MAC and PHY, USB 2.0, hibernation module, motion control pulse-width modulation, and a multitude of

simultaneous serial connectivity.

Contents

1 Board Overview.............................................................................................................. 2

1.1 Kit Contents.......................................................................................................... 3

1.2 Using the Ethernet LaunchPad Development Kit............................................................... 3

1.3 Features.............................................................................................................. 3

1.4 BoosterPack Plug-in Modules..................................................................................... 4

1.5 Specifications........................................................................................................ 4

2 Hardware Description ....................................................................................................... 5

2.1 Functional Description.............................................................................................. 5

2.2 Power Management............................................................................................... 20

2.3 Debug Interface.................................................................................................... 21

3 Software Development .................................................................................................... 21

3.1 Software Description.............................................................................................. 21

3.2 Source Code....................................................................................................... 21

3.3 Tool Options ....................................................................................................... 21

3.4 Programming the Ethernet LaunchPad Development Kit.................................................... 22

4 PCB Schematics ........................................................................................................... 22

List of Figures

1 SimpleLink Ethernet MSP432E401Y LaunchPad Development Kit................................................... 2

2 SimpleLink Ethernet LaunchPad Development Kit Block Diagram ................................................... 5

3 Default Jumper Locations................................................................................................. 18

4 BSL Header and Resistors................................................................................................ 19

5 Ethernet LaunchPad Development Kit Schematics (1 of 5) .......................................................... 23

6 Ethernet LaunchPad Development Kit Schematics (2 of 5) .......................................................... 24

7 Ethernet LaunchPad Development Kit Schematics (3 of 5) .......................................................... 25

8 Ethernet LaunchPad Development Kit Schematics (4 of 5) .......................................................... 26

9 Ethernet LaunchPad Development Kit Schematics (5 of 5) .......................................................... 27

List of Tables

1 MSP-EXP432E401Y Specifications....................................................................................... 4

2 BoosterPack Plug-in Module Interface 1 GPIO and Signal Muxing................................................... 8

3 BoosterPack 2 GPIO and Signal Muxing ............................................................................... 11

4 X11 Breadboard Adapter Odd-Numbered Pad GPIO and Signal Muxing.......................................... 14

5 X11 Breadboard Adapter Even-Numbered Pad GPIO and Signal Muxing......................................... 15

6 Resistors for Serial Bootloader Protocols............................................................................... 19

Board Overview

www.ti.com

2SLAU748B–October 2017–Revised September 2018

Submit Documentation Feedback

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

Trademarks

SimpleLink, LaunchPad, BoosterPack, Code Composer Studio are trademarks of Texas Instruments.

Arm, Cortex, Keil, RealView are registered trademarks of Arm Limited.

IAR Embedded Workbench is a registered trademark of IAR Systems.

All other trademarks are the property of their respective owners.

1 Board Overview

The SimpleLink Ethernet MSP432E401Y Microcontroller LaunchPad Development Kit is a low-cost

evaluation platform for SimpleLink Arm Cortex-M4F-based Ethernet microcontrollers. The Ethernet

LaunchPad development kit design highlights the MSP432E401Y microcontroller with its on-chip 10/100

Ethernet MAC and PHY, USB 2.0, hibernation module, motion control pulse-width modulation, and a

multitude of simultaneous serial connectivity. The Ethernet LaunchPad development kit also features two

user switches, four user LEDs, dedicated reset and wake switches, a breadboard expansion option and

two independent BoosterPack™ XL expansion connectors. The preprogrammed quick start application on

the Ethernet LaunchPad development kit also enables remote monitoring and control of the evaluation

board from an internet browser anywhere in the world. The web interface is provided by a third party,

Exosite. Each Ethernet LaunchPad development kit is enabled on the Exosite platform allowing users to

create and customize their own Internet-of-Things applications.

Figure 1 shows the Ethernet LaunchPad development kit with key features highlighted.

Figure 1. SimpleLink Ethernet MSP432E401Y LaunchPad Development Kit

www.ti.com

Board Overview

SLAU748B–October 2017–Revised September 2018

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

1.1 Kit Contents

The Ethernet LaunchPad development kit contains the following items:

• SimpleLink Ethernet MSP432E401Y LaunchPad Development Board (MSP-EXP432E401Y)

• USB Micro-B plug to USB-A plug cable

• Quick Start Guide

1.2 Using the Ethernet LaunchPad Development Kit

The recommended steps for using the Ethernet LaunchPad development kit are:

1. Run the Out of Box demo software. For detailed instruction on how to run the out of box demo, visit

this SimpleLink Academy tutorial.

2. Take the first step towards developing your own applications. The Ethernet LaunchPad development

kit is supported by the SimpleLink MSP432E4 SDK. After installing the SDK, look in the following

installation directories for bare metal and rtos based examples

a. examples\nortos\MSP_EXP432E401Y\

b. examples\rtos\MSP_EXP432E401Y\

See Section 3 for more details about software development.

3. Experiment with BoosterPack plug-in modules. This development kit conforms to the latest revision of

the BoosterPack plug-in module pinout standard. It has two independent BoosterPack plug-in module

connections to enable a multitude of expansion opportunities.

4. Customize and integrate the hardware to suit your end application. This development kit can be used

as a reference for building your own custom circuits based on SimpleLink microcontrollers or as a

foundation for expansion with your custom BoosterPack plug-in module or other circuit. This manual

can serve as a starting point for this endeavor.

5. More Resources. See the TI MCU LaunchPad web page for more information and available

BoosterPack modules.

1.3 Features

The Ethernet LaunchPad development kit includes the following features:

• SimpleLink MSP432E401Y microcontroller

• Ethernet connectivity with fully integrated 10/100 Ethernet MAC and PHY

• Motion Control PWM

• USB 2.0 Micro A/B connector

• 4 user LEDs

• 2 user switches

• 1 independent hibernate wake switch

• 1 independent microcontroller reset switch

• Jumper for selecting power source:

– XDS-110 USB

– USB Device

– BoosterPack

• Preloaded Internet-of-Things application

• I/O brought to board edge for breadboard expansion

• Two independent BoosterPack XL standard connectors featuring stackable headers to maximize

expansion through BoosterPack plug-in module ecosystem

Board Overview

www.ti.com

4SLAU748B–October 2017–Revised September 2018

Submit Documentation Feedback

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

1.4 BoosterPack Plug-in Modules

The Ethernet LaunchPad development kit provides an easy and inexpensive way to develop applications

with the MSP432E401YPDT microcontroller. BoosterPack plug-in modules are add-on boards that follow a

pinout standard created by TI. The TI and third-party ecosystem of BoosterPack plug-in modules greatly

expands the peripherals and potential applications that you can easily explore with the Ethernet

LaunchPad development kit.

You can also build your own BoosterPack plug-in module by following the design guidelines on the TI

website. TI even helps you promote your BoosterPack plug-in module to other members of the

community. TI offers a variety of avenues for you to reach potential customers with your solutions.

1.5 Specifications

Table 1 summarizes the specifications for the Ethernet LaunchPad.

Table 1. MSP-EXP432E401Y Specifications

Parameter Value

Board Supply

Voltage

4.75 VDC to 5.25 VDC from one of the following sources:

• XDS-110 USB Micro-B cable connected to PC or other compatible power source

• Target USB (U7) USB Micro-B cable connected to PC or other compatible power source

• BoosterPack 1 Interface (J3-21)

• BoosterPack 2 Interface (J7-21)

• 5-V Power header (J13-1)

• Breadboard expansion header (J10-2 or J10-97). See schematic symbol JP1 for power input selection.

Dimensions 6.85 in × 2.5 in × .425 in (17.4 cm × 6.35 cm × 10.8 mm) (L × W × H)

Break-out

Power Output

• 5 VDC to BoosterPack modules, current limited by TPS2052B. Nominal rating is 1 A. Board input power

supply limitations may also apply.

• 3.3 VDC to BoosterPack modules, limited by output of TPS79601 LDO. This 3.3-V plane is shared with

onboard components. Total output power limit of TPS79601 is 1 A.

RoHS Status Compliant

www.ti.com

Hardware Description

SLAU748B–October 2017–Revised September 2018

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

2 Hardware Description

The Ethernet LaunchPad development kit includes an MSP432E401YPDT microcontroller with an

integrated 10/100 Ethernet MAC and PHY. This advanced Arm Cortex-M4F MCU has a wide range of

peripherals that are made available to users through the onboard accessories and the BoosterPack plug-

in module connectors. This chapter explains how those peripherals operate and interface to the

microcontroller.

Figure 2 shows a high-level block diagram of the Ethernet LaunchPad development kit.

Figure 2. SimpleLink Ethernet LaunchPad Development Kit Block Diagram

2.1 Functional Description

2.1.1 Microcontroller

The MSP432E401Y is a 32-bit Arm Cortex-M4F based microcontroller with 1024KB of flash memory,

256KB of SRAM, 6KB of EEPROM, and 120-MHz operation, integrated 10/100 Ethernet MAC and PHY,

integrated USB 2.0 connectivity with external high-speed USB 3.0 PHY capability, a hibernation module, a

multitude of serial connectivity and motion control PWM, as well as a wide range of other peripherals. See

the MSP432E401Y microcontroller data sheet for more complete details.

Most of the microcontroller signals are routed to 0.1-in (2.54-mm) pitch headers or through-hole solder

pads. An internal multiplexor allows different peripheral functions to be assigned to each of these GPIO

pads. When adding external circuitry, consider the additional load on the evaluation board power rails.

The MSP432E401Y microcontroller is factory-programmed with a quick start demo program. The quick

start program resides in on-chip Flash memory and runs each time power is applied, unless the quick start

application has been replaced with a user program. The quick start application automatically connects to

http://ti.exosite.com when an internet connection is provided through the RJ45 Ethernet jack on the

evaluation board.

2.1.2 Ethernet Connectivity

The Ethernet LaunchPad development kit is designed to connect directly to an Ethernet network using

RJ45 style connectors. The microcontroller contains a fully integrated Ethernet MAC and PHY. This

integration creates a simple, elegant and cost-saving Ethernet circuit design. Example code is available for

LwIP TCP/IP protocol stack. The embedded Ethernet on this device can be programmed to act as an

HTTP server, client or both. The design and integration of the circuit and microcontroller also enable users

to synchronize events over the network using the IEEE1588 precision time protocol.

When configured for Ethernet operation, it is recommended that the user configure LED D3 and D4 to be

controlled by the Ethernet PHY to indicate connection and transmit or receive status.

Hardware Description

www.ti.com

6SLAU748B–October 2017–Revised September 2018

Submit Documentation Feedback

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

2.1.2.1 RJ-45 Connections

To improve EMI performance, use a metal-shielded RJ-45 connector with the shield connected to chassis

ground.

Bob Smith termination to the RJ-45 connector involves 75-Ωtermination resistors connected to the

unused differential pair connections on the RJ-45 connector. Bob Smith termination is used to reduce

noise that results from common-mode current flows and to reduce susceptibility to noise from unused wire

pairs on the RJ-45.

NOTE: Power Over Ethernet (PoE) applications require a modified Bob Smith termination, which

consists of DC-blocking capacitors in series with the 75-Ωtermination resistors.

2.1.3 USB Connectivity

The Ethernet LaunchPad development kit is designed to be USB 2.0 ready. A TPS2052B load switch is

connected to and controlled by the microcontroller USB peripheral, which manages power to the USB

micro A/B connector when functioning in a USB host. When functioning as a USB device, the entire

Ethernet LaunchPad development kit can be powered directly from the USB micro A/B connector. Use

JP1 to select the desired power source.

USB 2.0 functionality is provided and supported directly out of the box with the target USB micro A/B

connector. High-speed USB 3.0 functionality can be enabled by adding an external USB PHY. The USB

external PHY control and data signals are provided on the breadboard expansion header J10.

2.1.4 Motion Control

The Ethernet LaunchPad development kit includes motion control functionality through the use of a PWM

module capable of generating eight PWM outputs. The PWM module provides a great deal of flexibility

and can generate simple PWM signals – for example, those required by a simple charge pump – as well

as paired PWM signals with dead-band delays, such as those required by a half-H bridge driver. Three

generator blocks can also generate the full six channels of gate controls required by a 3-phase inverter

bridge.

A quadrature encoder interface (QEI) is also available to provide motion control feedback.

See Section 2.1.6 for details about the availability of these signals on the BoosterPack interfaces.

2.1.5 User Switches and LEDs

Two user switches are provided for input and control of the MSP432E401Y software. The switches are

connected to GPIO pins PJ0 and PJ1.

A reset switch and a wake switch are also provided. The reset switch initiates a system reset of the

microcontroller whenever it is pressed and released. Pressing the reset switch also asserts the reset

signal to the BoosterPack plug-in module and Breadboard headers. The wake switch is one way to bring

the device out of hibernate mode.

Four user LEDs are provided on the board. D1 and D2 are connected to GPIOs PN1 and PN0. These

LEDs are dedicated for use by the software application. D3 and D4 are connected to GPIOs PF4 and

PF0, which can be controlled by user’s software or the integrated Ethernet module of the microcontroller.

A power LED is also provided to indicate that 3.3-V power is present on the board.

www.ti.com

Hardware Description

SLAU748B–October 2017–Revised September 2018

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

2.1.6 BoosterPack Plug-in Modules and Headers

2.1.6.1 BoosterPack Plug-in Module Interface 1

The Ethernet LaunchPad development kit features two fully independent BoosterPack XL connectors.

BoosterPack Plug-in Module Interface 1, located near the XDS110 emulator, is fully compliant with the

BoosterPack plug-in module standard.

I2C is provided in both the original BoosterPack plug-in module standard configuration as well as the

updated standard location. Use of I2C on the bottom left of the BoosterPack plug-in module connections

per the updated standard is highly encouraged whenever possible.

Motion control advanced PWM connections are provided on the inner right connector for motion control

applications.

Table 2 lists the BoosterPack plug-in module pins and the GPIO alternate functions available on each pin.

The MSP432E401Y GPIO register GPIOPCTL values are shown for each configuration. The headers in

this table are labeled from left to right in ten pin columns. J1 and J2 make up the outer BoosterPack plug-

in module standard pins, and J3 and J4 make up the inner BoosterPack XL standard pins.

Hardware Description

www.ti.com

8SLAU748B–October 2017–Revised September 2018

Submit Documentation Feedback

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

Table 2. BoosterPack Plug-in Module Interface 1 GPIO and Signal Muxing

Header Pin Standard

Function GPIO MCU Pin Analog Digital Function (GPIOPCTL Bit Encoding)

1 2 3 5 6 7 8 11 13 14 15

J1 1 3.3 V 3.3 V

J1 2 Analog PE4 123 AIN9 U1RI – – – – – – – – – SSI1XDAT0

J1 3 UART RX PC4 25 C1- U7Rx – – – – – – – – – EPI0S7

J1 4 UART TX PC5 24 C1+ U7Tx – – – – RTCCLK – – – – EPI0S6

J1 5 GPIO PC6 23 C0+ U5Rx – – – – – – – – – EPI0S5

J1 6 Analog PE5 124 AIN8 – – – – – – – – – – SSIXDAT1

J1 7 SPI CLK PD3 4 AIN12 – I2C8SDA T1CCP1 – – – – – – – SSI2CLk

J1 8 GPIO PC7 22 C0- U5Tx – – – – – – – – – EPI0S4

J1 9 I2C SCL PB2 91 – – I2C0SCL T5CCP0 – – – – – – USB0STP EPI0S27

J1 10 I2C SDA PB3 92 – – I2C0SDA T5CCP1 – – – – – – USB0CLK EPI0S28

J3 21 5 V 5 V

J3 22 ground GND

J3 23 Analog PE0 15 AIN3 U1RTS – – – – – – – – – –

J3 24 Analog PE1 14 AIN2 U1DSR – – – – – – – – – –

J3 25 Analog PE2 13 AIN1 U1DCD – – – – – – – – – –

J3 26 Analog PE3 12 AIN0 U1DTR – – – – – – – – – –

J3 27 Analog PD7 128 AIN4 U2CTS – T4CCP1 USB0PFLT – – NMI – – – SSI2XDAT2

J3 28 Analog PD6 127 AIN5 U2RTS – T4CCP0 – USB0EPEN – – – – – SSI2XDAT3

J3 29 A out PM4 74 TMPR3 U0CTS – T4CCP0 – – – – – – – –

J3 30 A out PM5 73 TMPR2 U0DCD – T4CCP1 – – – – – – – –

J4 40 PWM PF1 43 – – – – EN0LED2 M0PWM1 – – – – SSI3XDAT0 TRD1

J4 39 PWM PF2 44 – – – – – M0PWM2 – – – – SSI3Fss TRD0

J4 38 PWM PF3 45 – – – – – M0PWM3 – – – – SSI3Clk TRCLK

J4 37 PWM PG0 49 – – I2C1SCL – EN0PPS M0PWM4 – – – – – EPI0S11

J4 36 Capture PL4 85 – – – T0CCP0 – – – – – – USB0D4 EPI0S26

J4 35 Capture PL5 86 – – – T0CCP1 – – – – – – USB0D5 EPI0S33

J4 34 GPIO PL0 81 – – I2C2SDA – – M0FAULT3 – – – – USB0D0 EPI0S16

J4 33 GPIO PL1 82 – – I2C2SCL – – PhA0 – – – – USB0D1 EPI0S17

J4 32 GPIO PL2 83 – – – – C0o PhB0 – – – – USB0D2 EPI0S18

J4 31 GPIO PL3 84 – – – – C1o IDX0 – – – – USB0D3 EPI0S19

J2 11 ground GND

J2 12 PWM PM3 75 – – – T3CCP1 – – – – – – – EPI0S12

J2 13 GPIO PH2 31 – U0DCD – – – – – – – – – EPI0S2

J2 14 GPIO PH3 32 – U0DSR – – – – – – – – – EPI0S3

J2 15 reset RESET

J2 16 SPI MOSI PD1 2 AIN14 – I2C7SDA T0CCP1 C1o – – – – – – SSI2XDAT0

J2 17 SPI MISO PD0 1 AIN15 – I2C7SCL T0CCP0 C0o – – – – – – SSI2XDAT1

J2 18 GPIO PN2 109 – U1DCD U2RTS – – – – – – – – EPI0S29

J2 19 GPIO PN3 110 – U1DSR U2CTS – – – – – – – – EPI0S30

www.ti.com

Hardware Description

SLAU748B–October 2017–Revised September 2018

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

Table 2. BoosterPack Plug-in Module Interface 1 GPIO and Signal Muxing (continued)

Header Pin Standard

Function GPIO MCU Pin Analog Digital Function (GPIOPCTL Bit Encoding)

1 2 3 5 6 7 8 11 13 14 15

J2 20 GPIO PP2 103 – U0DTR – – – – – – – – USB0NXT EPI0S29

Hardware Description

www.ti.com

10 SLAU748B–October 2017–Revised September 2018

Submit Documentation Feedback

SimpleLink™ Ethernet MSP432E401Y Microcontroller LaunchPad™

Development Kit (MSP-EXP432E401Y)

2.1.6.2 BoosterPack Plug-in Module Interface 2

The second BoosterPack XL interface is located near the bottom of the board. This interface is fully

compliant with the BoosterPack plug-in module standard, and adds features not covered by the

BoosterPack plug-in module standard that enable operation with additional BoosterPack plug-in modules.

Using the jumpers JP4 and JP5, Controller Area Network (CAN) digital receive and transmit signals can

be optionally routed to the BoosterPack Plug-in Module Interface 2 connector. In the default configuration,

UART0 is used for the XDS-110 backchannel UART and CAN is not present on the BoosterPack plug-in

module headers. In this configuration, the ROM serial bootloader can be used over the XDS-110

backchannel UART. When the jumpers are configured for CAN on the BoosterPack plug-in module

interface, then UART2 must be used for the XDS-110 backchannel UART.

To comply with both the original and the new BoosterPack plug-in module standard, I2C is provided on

both sides of the BoosterPack plug-in module connection. Use of I2C on the bottom left of the BoosterPack

plug-in module connection is highly encouraged where possible, to be in compliance with the new

BoosterPack plug-in module standard. To provide I2C capability on the right side of the connector, per the

original standard, two 0-Ωresistors (R19 and R20) are used to combine the SPI and I2C signals. These

signals are not shared with any other pins on the LaunchPad development kit and therefore removal of

these zero-ohm resistors should not be required. Software should be certain that unused GPIO signals are

configured as inputs.

Table 3 lists the BoosterPack plug-in module pins and the GPIO alternate functions available at each pin.

The MSP432E401Y GPIO register GPIOPCTL values are shown for each configuration. The headers in

this table are labeled from left to right in ten pin columns. J5 and J6 make up the outer BoosterPack

standard pins, J7 and J8 make up the inner BoosterPack XL standard pins.

Tabla de contenidos

Otros manuales de Microcontrolador de Texas Instruments

Texas Instruments

Texas Instruments TAS5132DDV6EVM Manual de usuario

Texas Instruments

Texas Instruments MSP430F6725A Manual de usuario

Texas Instruments

Texas Instruments TMS320F28069 Manual de usuario

Texas Instruments

Texas Instruments TMDX654IDKEVM Manual de usuario

Texas Instruments

Texas Instruments CC13 Series Manual de usuario

Texas Instruments

Texas Instruments CC1125 Manual de usuario

Texas Instruments

Texas Instruments MSP430 series Manual de usuario

Texas Instruments

Texas Instruments TMS320C6000 DSP Manual de usuario

Texas Instruments

Texas Instruments LAUNCHXL-CC1310 Manual

Texas Instruments

Texas Instruments CC3220 Manual de usuario

Texas Instruments

Texas Instruments TMS320F2837 D Series Manual de usuario

Texas Instruments

Texas Instruments MSP430C311S Manual de usuario

Texas Instruments

Texas Instruments MSP430F67781 Manual de usuario

Texas Instruments

Texas Instruments LMK03318EVM Manual de usuario

Texas Instruments

Texas Instruments CC110 Series Guía

Texas Instruments

Texas Instruments SimpleLink CC3200 Wi-Fi Manual

Texas Instruments

Texas Instruments SWRU351 Manual de usuario

Texas Instruments

Texas Instruments CC2510 Manual de programación

Texas Instruments

Texas Instruments eZ430-Chronos Manual de usuario

Texas Instruments

Texas Instruments SimpleLink MSP432E4 Manual del producto

Texas Instruments

Texas Instruments TLC6C5712-Q1 Manual de usuario

Texas Instruments

Texas Instruments TLC2543 Manual de usuario

Texas Instruments

Texas Instruments TMS370 Series Guía del usuario

Texas Instruments

Texas Instruments mmWaveICBoost Manual de usuario

Manuales populares de Microcontrolador de otras marcas

AMS

AMS AS7261 Demo Kit Manual de usuario

Novatek

Novatek NT6861 Manual de usuario

Espressif Systems

Espressif Systems ESP8266 SDK Guía de configuración

Nuvoton

Nuvoton ISD61S00 ChipCorder Guía

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manual de usuario

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario

NEC

NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento

Mikroe

Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento

Intel

Intel Agilex Manual de usuario

Cypress

Cypress CY4607 HX2VL Manual de usuario

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manual de usuario

CYPRES

CYPRES CY14NVSRAMKIT-001 Manual de usuario

Espressif Systems

Espressif Systems ESP8266EX Instrucciones de funcionamiento

Abov

Abov AC33M8128L Manual de usuario

Laird

Laird BL654PA Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F800 Manual de usuario

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manual de usuario

Mikroe

Mikroe click Proximity 2 Manual de usuario