Texas Instruments CC2531 Manual de usuario

SWRU351A

October 2013

ZigBee Light Link Development Kit Quick Start Guide

Opening the box and setting up a ZLL network

1. Kit Contents

3 x Zlight2 LED boards

1 x Remote Control

1 x CR2025 Battery

3 x micro-USB cables

Documentation

2. Regulatory Information

The Zlight2 boards and the Remote control are FCC-

and IC certified and they are tested to comply with

ETSI/R&TTE over temperature from 0 to +35°C. The

Remote control has an on-board inverted F PCB

antenna while the Zlight2 has an on-board half wave

dipole PCB antenna.

FCC/IC Regulatory Compliance

FCC Part 15 Class A Compliant

IC ICES-003 Class A Compliant

Caution! The kit contains ESD sensitive

components. Handle with care to prevent

permanent damage.

3. Purpose of the Kit

The CC2531 ZigBee Light Link (ZLL) development kit

is intended for customers who would like to evaluate

ZLL lighting control for LED light products, and

develop simple applications and demonstrators

based on this standard.

The kit contains everything needed to set up a ZLL

network and control the lights individually or as a

group. It’s also possible to extend the kit with more

HW to allow cloud based control solutions such as

Ninja blocks (http://www.ninjablocks.com/).

Information about this can be found by following the

links supplied at the end of the document.

4. Operating the Zlight2

Caution! To minimize the risk of

fire or equipment damage, make

sure that ambient temperature air

is allowed to circulate freely

around the Zlight2 board when

operating. Avoid touching components during

operation if symbolized as hot. A thermal shutdown

routine is implemented in the included firmware

running on the lights. Always make sure that this

routine is implemented if you flash your own

firmware. The easiest way to do that is to base it

on ZStack-Lighting-1.0.2 or later releases from

Texas Instruments.

Caution! DO NOT STARE

DIRECTLY INTO THE LED

LIGHT SOURCE. Intense light

sources have a high secondary

exposure potential due to their

blinding effect. A temporary reduction in visual

acuity and afterimages can occur, leading to

irritation, annoyance, visual impairment, and even

accidents, depending on the situation. Always

consider the use of light filtering/darkening

protective eyewear and be fully aware of

surrounding laboratory type set-ups when viewing

intense light sources to minimize/eliminate such

risks in order to avoid accidents related to

temporary blindness.

RISK GROUP 2

CAUTION

Possible hazardous optical radiation

emitted from this product.

Do not stare at operating lamp. May be

harmful to eyes.

Do not stare at operating LEDs

(Risk Group 1 (RG1) @ 0.9m)

Per IEC 62471 ed 1.0: 2006-07 (“Photobiological Safety

of Lamps and Lamp Systems”) this product has been

classified in Risk Group 2. Products classified as Risk

Group 2 do not pose a hazard due to the aversion

response to very bright light sources or due to thermal

discomfort.

It should be noted that INTENTIONALLY staring at the

lamp for extended lengths of time from short distances

could lead to a potential risk of eye damage due to a

retinal blue-light hazard. In order to reduce the potential

of exposure to a retinal blue-light hazard, the operator

must avoid any direct view of the LEDs while in

operation, from a distance of 0.9m, or closer.

5. Powering the Boards

The Zlight2 boards are powered through the USB

connector. It is recommended that they are powered

from a dedicated USB power supply capable of

supplying 800mA and max 5.5V.

External Power SupplyRequirements:

Nom Voltage: 5 VDC

Max Current: 800 mA

Efficiency Level V

Note! When using an external power supply, make sure it meets

the listed requirements in addition to complying with applicable

regional product regulatory and safety certification requirements

such as UL, CSA, VDE, CCC, and PSE.

The Remote control is powered by a 3V CR2025

battery (included). Do not use other battery types.

Battery Requirements:

CR2025 UL Recognized Component Battery

Voltage: 3 V

Min Capacity: 165 mAh

NOTE: Only use Varta or Energizer CR2025 battery or equivalent.

Connect the Zlight2 boards to your USB power

supply using the supplied cables.

Insert the CR2025 battery into the

remote control. Follow the

instructions on the back of the

remote for correct placement.

6. Starting the Network

In ZLL, the process of pairing a new lamp with

a remote control is called touch linking.

Touch link the first Zlight2 board by holding

the remote control close and simultaneously

pressing the “on” and “off” buttons.

Quickly release both buttons. After a few

seconds, the Zlight2 will flash, and the remote

control will give a short beep.

Figure 1: Touch Link

Starting the Network (cont.)

To confirm a successful touch link, you may press the

“on” button, and then the “off” button, and verify that

the lamp switches on and off accordingly.

Continue by touch linking the remaining 2 Zlight2

boards, one at a time.

Note that if the two buttons are pressed with too much

time difference, the “on” or “off” command will be sent

to the previously touch linked Zlight2 instead of

initiating a new touch link command. Try again.

7. Operating the Zlight2

Once connected to the ZLL network through touch

linking, the Zlight2s can be controlled with the remote

control. The remote control will always address a

target, which can be an individual lamp, or a group of

lamps.

Please turn the page

Lamp 2

…

Lamp N

RC Group

(unique to

the remote)

Lamp 1

Use the < > buttons to select target

Operating the Zlight2 (cont.)

The touch link operation, in addition to

bringing the Zlight2 on to the ZLL network,

also adds it to the remote control’s own

group, the RC Group. When more than one

lamp is on the network, repeatedly pressing

the or button on the remote will cycle

through all the individual lights, and the RC

Group, in a circular manner ( > cycles

clockwise and < cycles counter-clockwise).

The lamps will blink to identify when they are

selected, and the next command will be sent

to the last selected target. Select RC Group

by pressing the left or right arrow button until

all the lamps blink simultaneously to identify.

Operating the Zlight2 (cont.)

You can now control level, color and saturation on all

the lamps. The on/off commands will also be sent to

the RC Group.

Level up: Increase intensity

Level down: Decrease intensity

Color (Hue) up: Change colour

Color (Hue) down: Change colour

Sat up: Increase saturation (“more color”)

Sat down: Decrease saturation (“more white”)

Note: Changing the color (hue) will not produce a

visible change in the light if the Saturation is set to

minimum, i.e. white light.

8. Next Steps

For more advanced use and colour control, go to the

TI ZigBee Light Link wiki page by following the link

found at the end of this document.

Additional Tools and Links

CC debugger

The CC debugger is a tool that allows you to flash

and debug the Zlight2 using SmartRF Flash

Programmer or IAR Embedded Workbench. It

connects to a USB port on your PC and to the

debug header on the Zlight2 board.

CC2531 USB dongle

The CC2531 USB dongle plugs into a Linux or

Windows host and can serve as a gateway for

cloud based lighting

control.

SmartRF Flash Programmer

Texas Instruments has a simple tool which can

be used to program and flash the Zlight2.

SmartRF Flash Programmer can be

downloaded from www.ti.com/tool/flash-

programmer

IAR Embedded Workbench

To develop software, program, and debug the

Zlight2, you should use IAR Embedded

Workbench for 8051.

More information on IAR EW8051, including a free

evaluation version download, can be found at

www.iar.com/ew8051.

Useful Links

TI ZigBee Light Link wiki page:

http://processors.wiki.ti.com/index.php/ZStack-

Lighting_Kit

Useful Links

Kit Product Page

http://www.ti.com/tool/cc2530zdk-zll

CC2530 and CC2531 User’s Guide

http://www.ti.com/lit/swru191

For additional help, visit the TI E2E Forum

www.ti.com/lprf-forum

The Zlight2 lights supplied in this kit are powered by OSLON LEDs from Osram. Please visit the LED Light for you web

site to learn more about LED lighting and ZigBee Light Link wireless control examples.

http://www.ledlightforyou.com/Partners/Highlights/en-ZigBee-Lighting-Control.php

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Otros manuales para CC2531

Tabla de contenidos

Otros manuales de Microcontrolador de Texas Instruments

Texas Instruments

Texas Instruments TPS3703 Manual de usuario

Texas Instruments

Texas Instruments MSP432P401R Manual de usuario

Texas Instruments

Texas Instruments CC2652RSIP Manual de usuario

Texas Instruments

Texas Instruments CC2531 Manual de usuario

Texas Instruments

Texas Instruments MSP430F663x Manual de usuario

Texas Instruments

Texas Instruments MSP430F67761 Manual de usuario

Texas Instruments

Texas Instruments CC3220 Manual de usuario

Texas Instruments

Texas Instruments eZ430-Chronos Manual de usuario

Texas Instruments

Texas Instruments MUX36D04EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manual de usuario

Texas Instruments

Texas Instruments AM243x Manual de usuario

Texas Instruments

Texas Instruments Chipcon Products CC2400DK Manual de usuario

Texas Instruments

Texas Instruments CC1110 Manual de usuario

Texas Instruments

Texas Instruments SimpleLink MSP432E4 Manual del producto

Texas Instruments

Texas Instruments AFE4403 Manual de usuario

Texas Instruments

Texas Instruments MSP430F6749 Manual de usuario

Texas Instruments

Texas Instruments MSP430F67681 Manual de usuario

Texas Instruments

Texas Instruments TMS570 Manual de usuario

Texas Instruments

Texas Instruments TLC2543 Manual de usuario

Texas Instruments

Texas Instruments MSP430F5638 Manual de usuario

Texas Instruments

Texas Instruments LOGIC PD ZOOM DM3730 SOM-LV Manual de usuario

Texas Instruments

Texas Instruments TMS570LC43x Manual de usuario

Texas Instruments

Texas Instruments C2000 Piccolo LaunchPad Guía de instalación

Texas Instruments

Texas Instruments Chipcon Products CC1110DK Manual de usuario

Manuales populares de Microcontrolador de otras marcas

AMS

AMS AS7261 Demo Kit Manual de usuario

Novatek

Novatek NT6861 Manual de usuario

Espressif Systems

Espressif Systems ESP8266 SDK Guía de configuración

Nuvoton

Nuvoton ISD61S00 ChipCorder Guía

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manual de usuario

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario

NEC

NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento

Mikroe

Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento

Intel

Intel Agilex Manual de usuario

Cypress

Cypress CY4607 HX2VL Manual de usuario

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manual de usuario

CYPRES

CYPRES CY14NVSRAMKIT-001 Manual de usuario

Espressif Systems

Espressif Systems ESP8266EX Instrucciones de funcionamiento

Abov

Abov AC33M8128L Manual de usuario

Laird

Laird BL654PA Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F800 Manual de usuario

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manual de usuario

Mikroe

Mikroe click Proximity 2 Manual de usuario