Texas Instruments CC2530 ZigBee Development Kit Manual de usuario

CC2530 ZigBee Development

Kit User’s Guide

swru209

Table of contents

CC2530 ZIGBEE DEVELO

PMENT KIT USER’S GUI

................................

.............

INTRODUCTION

................................

.....

ABOUT THIS MANUAL

................................

.........................

ACRONYMS

................................

.............

ZIGBEE DEVELOPMENT K

IT CONTENTS

................................

......................

GETTING STARTED

................................

..............................

5.1

ETTING UP THE HARDWA

................................

........................

5.2

UNNING THE

REPROGRAMMED

ENSOR

EMO

................................

...........

5.3

CC2530

PER

TEST

................................

.......

5.4

VALUATE THE

CC2530

ADIO USING

MART

TUDIO

................................

..........

5.5

EVELOPING

YOUR OWN SOFTWARE WI

TH THE

CC2530

................................

............

5.6

EVELOPING YOUR OWN H

ARDWARE WITH THE

CC2530

................................

..........

RF TESTING

................................

...........

6.1

ARAMETER

ESTING

ASICS

................................

..............

6.2

ARAMETER

ESTING

ASICS

................................

..............

CC2530EM

................................

..............

CC2531 USB DONGLE

................................

..........................

SMARTRF05

EVALUATION BOARD

................................

SMARTRF05 BATTERY BO

ARD

................................

.......

10.1

OYSTICK

................................

...................

10.2

CONNECTORS

................................

.......

10.3

ELECTION

WITCH

................................

.............................

10.4

ROBE CONNECTORS

................................

10.5

EBUG CONNECTOR

................................

...........................

10.6

URRENT

EASUREMENT

UMPER

................................

............

FREQUENTLY ASKED

QUESTIONS

................................

REFERENCES

................................

........

DOCUMENT HISTORY

................................

........................

APPENDIX A

SCHEMATICS

................................

....................

swru209

Introduction

Thank you for purchasing the CC2530 ZigBee Development Kit.

The CC2530 is Texas Instrument’s second generation ZigBee/IEEE 802.15

.4 compliant System

Chip with an optimized 8051 MCU core and radio for the 2.4 GHz unlicensed ISM/SRD band. This

device enables industrial grade applications by offering state

the

art noise immunity, excellent link

budget, operation up to 125 degrees

and low voltage operation.

In addition, the CC2530 provides extensive hardware support for packet handling, data buffering, burst

transmissions, data encryption, data authentication, clear channel assessment, link quality indication

and packet timing inf

ormation.

Stack™is TI's ZigBee compliant protocol stack for a growing portfolio of IEEE 802.15.4 products

and platforms. Z

Stack support the CC2530 and is compliant with both the ZigBee® 2007 (ZigBee and

ZigBee PRO) and ZigBee® 2006 specification.

e CC2530 ZigBee Development Kit is well suited for demonstration, evaluation and software

development targeting IEEE 802.15.4 and ZigBee compliant applications with the CC2530.

The CC2530 product folder on the web

[1]

has more information, with datasheets, user guides and

application notes. For more information about TI’s ZigBee software implementation, refer to the

Stack

product folder on the web

[7]

. This web site also has links for download of Z

stack.

About this manual

This manual describes all the hardware included in the CC2530 ZigBee Development Kit

(CC2530ZDK)

and points to other useful information resources.

Chapter

briefly describes the contents of the development kit and chapter

gives a quick

introduction to how to get started with the kit. In particular, it describes how to install SmartRF Studio

to get the required drivers for the evaluation board, how the hardware can b

e used, and lists the

software that is available for the development kit. Chapter

explains some simple methods for

performing practical RF testing with the devel

opment kit. Chapter

, and

describe the hardware in

the kit and where to find more information about how to use it. A troubleshooting guide can be found in

chapter

The CC2530ZDK Quick Start Guide

[9]

has a short tutorial on how to get started with this kit.

More information and user manuals for the PC tools SmartRF Studio and

SmartRF

Flash Programmer

can be found on their respective pro

duct sites on the web

[2]

[3]

Please visit the CC2530 ZigBee Develop

ment Kit

[11]

web page and CC2530 product page

[1]

for

additional info

rmation. Further information can be found on the TI LPRF Online Community

[16]

Refer also to the document CC2530DK User’s Guide

[13]

which gives a detailed description of how to

set up the software development environment for the CC2530. This document also lists other available

software solutions for CC2530.

See chapter

for a list of relevant documents and links.

swru209

Acronyms

ACM

Abstract Control Model

Battery Board

CDC

Communications Device Class

Development Kit

Evaluation Board

Evaluation Module

HID

Human Interface Device

Integrated Circuit

ISM

Industrial, Scientific and Medical

Kilo Byte (1024 byte)

LCD

Liquid Crystal Display

LED

Light Emitting Diode

LPRF

Low Power RF

MCU

Micro Controller

Not connected

PER

Packet Error Rate

Radio Frequency

Receive

SoC

System on Chip

SPI

Serial Peripheral Interface

SRD

Short Range Device

Texas Instruments

Transmit

UART

Universal Asynchronous Receive Transmit

USB

Universal Serial Bus

ZDK

ZigBee Development Kit

Stack

TI’s ZigBee software implementation

swru209

ZigBee Development Kit contents

The CC2530 ZigBee

Development Kit

(CC2530

DK) includes hardware and software that allows

quick testing of the CC2530 RF performance and offers a complete platform for development of

advanced prototype RF systems and ZigBee applications.



Evaluate the CC2530 and ZigBee right out of the box. The ki

t can be used to demonstrate a small

sensor network application using ZigBee and the CC2530.



Use the CC2530ZDK to do software development of your own ZigBee applications using

Stack™

for CC2530.



Use SmartRF Studio to perform RF measurements. The radio

can be easily configured to

measure sensitivity, output power and other RF parameters.



Prototype development. All I/O pins from the CC2530 are available on pin connectors on the

SmartRF05EB, allowing easy interconnection to peripherals on the EB board or

other external

sensors and devices.

The CC2530ZDK contains the following components



2 x SmartRF05EB (the two large boards)



5 x SmartRF05 Battery Boards



7 x CC2530 Evaluation Modules (with the CC2530 and antenna connector)

2 of these CC2530EM’s are

pre

programmed with the SensorDemo Collector application

5 of the CC2530EM’s are pre

programmed with the SensorDemo Sensor application



7 x Antennas



1 x CC2531 USB Dongle



Cables



Batteries



Documents

Figure

CC2530 ZigBee Development Kit Contents

Consult the CC2530ZDK Quick Start Guide

[9]

and the CC2530ZDK Sensor Demo User’s Guide

[10]

for a description of the software programmed on the CC2530EM’s.

swru209

SmartRF05EB

The SmartRF05EB (evaluation board) is the

main board in the kit with a wide range of user

interfaces:



3x16 character serial LCD



Full speed USB 2.0 interface



UART



LEDs



Serial Flash



Potentiometer



Joyst

ick



Buttons

The EB is the platform for the evaluation

modules (EM) and can be connected to the PC

via USB to control the EM.

CC2530EM

The CC2530EM (evaluation module) contains

the RF IC and necessary external components

and matching filters for getting the most out of

the radio. The module can be plugged into the

SmartRF05EB.

Use the EM as reference

design for RF layout.

The schematics a

included at the end of this document and the

layout files can be found on the web

[1]

CC2531 USB Dongle

The CC2531 USB Dongle is a fully operational

USB d

evice that can be plugged into a PC.

The dongle has 2 LEDs, two small push

buttons and connector holes that allow

connection of external sensors or devices. The

dongle also has a connector for programming

and debugging of the CC2531 USB controller.

The do

ngle comes preprogrammed with

firmware such that it can be used as a packet

sniffer device.

SmartRF05BB

The SmartRF05 Battery Board can be used as

an alternative to the EB, providing a

standalone

node when the CC2530EM is

connected. It is powered with

2 AA batteries in

the sockets underneath the board. The board

peripherals include 4 LED’s, 2 push buttons

and a joystick. The BB also has a SoC debug

connector for connection to an external

debug/programming tool e.g. the

SmartRF05EB.

swru209

Getting

started

5.1

Setting up the hardware

After opening the kit, make sure you have all components. Please contact your TI Sales

Representative or TI Support

[17]

if anything is missing.

Start by connecting the antennas to the SMA connector on the RF evaluation boards. Tighten the

antenna’s screw firmly on to the SMA connector. If not properly connected, you might see reduced RF

performance. It is also possible to

connect the EM board to RF instruments via coax cables. The EM is

designed to match a 50 Ohm load at the SMA connector.

Figure

CC2530ZDK assembled hardware

Next, the evaluation modules should be plugged in to the SmartRF0

5EB’s and to the SmartRF05BB’s.

A ZigBee sensor demo application is preprogrammed on the CC2530EM’s included in this kit. The

application consists of two different device types; collectors and sensors. 5 of the CC2530EM’s are

programmed as the sensor devic

e type. When running the out of the box demonstration the sensor

EM’s shall be connected to the BB’s. The two EM’s programmed as collector device shall be

connected to the EB’s.

When not using the out of the box demonstration (i.e. the preprogrammed appl

ication) e.g, for RF

evaluation or software development, all of the 7 EM’s can be used equally.

The purpose of the SmartRF05EB is to serve as a general I/O board for testing of the various

peripherals of the CC2530 microcontroller. The SmartRF05EB is also used for programming and

debugging of the CC2530, and has several useful peripheral devices like

LCD, LED’s, I/O connectors,

push buttons and joystick etc.

The evaluation board can be powered from several different sources:



2 x 1.5V AA batteries (included in this kit)



USB (via the USB connector)



DC power (4 to 10 Volt) (not included in this kit)

swru209



xternal regulated power source (not included in this kit)

The power source can be selected using jumper P11 on the SmartRF05EB. The SmartRF05EB User’s

Guide

[6]

rovides more details.

The SmartRF05 Battery Boards (BB) can be used as a standalone device when equipped with a

CC2530EM. This board is powered by AA batteries. See section

in this document for more

information about the SmartRF05BB.

After assembling the hardware, you now have several options for working with the CC2530:



Run the Sensor D

emo ZigBee application that is preprogrammed on the CC2530’s.

The

CC2530ZD

K Quick Start Guide document

[9]

included in this kit describes the necessary

steps to run the demonstration.



Running the

packet error rate (

PER

)

test software available for CC2530EM.

Chapter

5.3

describes this application.



Evaluate and explore the RF capabilities of the CC2530 using SmartR

F Studio.

Chapter

5.4

provides the details how to do so.



Develop your own software for the CC2530.

Install IAR Embedded Workbench for 8051

and set up your first s

oftware project. Section

5.5

explains how.



Develop your own hardware with the CC2530.

See chapter

5.6

5.2

Running the Preprogrammed ZigBee Sensor Demo

The CC2530EM’s are pre

programmed with a Sensor Demo application used to demonstrate a

temperature monitoring application in a small ZigBee network. The CC2530ZDK Quick Start Guide

document

[9]

included in this kit describes the necessary steps to run the demonstration.

A software package with the source code for the Sensor Demo, and Intel HEX files ready to be

programmed on the devices, is available on the CC2530ZDK web site

[11]

. A detailed description

about the Sensor Demo application is found in the document CC2530ZDK Sensor Demo User’s Guide

[10]

5.3

CC2530 PER test

A Packet Error Rate

(PER) test application is also available for the CC2530. This application can be

used to evaluate the RF performance of CC2530 using either the hardware included in the kit or other

boards with a CC2530.

More information about the PER test application ca

n be found in the documents CC2530DK Quick

Start Guide

[12]

and

CC2530 Software Examples User's Guide

[13]

A software package with the source code for the PER test application, and Intel HEX files ready to be

programmed on the devices, is available on the CC2530DK web site

[14]

5.4

Evaluate the CC2530 Radio using SmartRF Studio

SmartRF Studio is a PC application developed for configuration and evaluation of many of the RF

products from Texas Instruments, including the CC2530. The

application communicates with the

CC2530 via the USB controller

on the SmartRF05EB board. The USB controller uses the debug

interface of the CC2530 to execute commands and to read and write registers.

SmartRF Studio lets you explore the radio on the CC2530, as it gives you full overview and access to

the radio registers. The tool has a control interface for running basic radio performance tests from the

swru209

PC. SmartRF Studio also offers a flexible code exp

ort function of radio register settings for software

developers.

Before proceeding, please download and install the latest version of SmartRF Studio from the web

[2]

By installing Studio, the USB drivers needed for proper interaction between the PC and the hardware

of the CC2530DK will also be installed.

In order to use the SmartRF Studio with CC2530, connect the CC2530EM to the SmartRF05EB. Next,

connect the Smar

tRF05EB board to the PC via one of the USB cables included in the kit. If you have

installed SmartRF Studio, select automatic installation of driver in the device wizard that appears. The

device wizard will only pop up when you turn on the SmartRF05EB and

only once for each board.

Allow Windows to complete the driver installation before proceeding.

With the board connected to the PC, you can start SmartRF Studio. The following window should

appear:

Figure

CC2530 and SmartRF

Studio

Make sure you select the tab called

“2.4 GHz”. The tab will indicate if there is a board/device

connected, and you should see the CC2530 icon highlighted as in the screenshot above.

Double click

on the

CC2530 icon, and

a new window will appear.

swru209

Figure

CC2530 control panel in SmartRF Studio

Figure

shows the main control panel for the CC2530. It lets you perform a number of oper

ations:



Run TX Test modes for testing of RF output power and spectrum; e.g. by connecting a

spectrum analyser or a power meter to the CC2530EM SMA connector to perform RF

measurements.



Run Packet TX and RX tests. For this test, you should have two EBs wit

h CC2530EMs

connected to the PC.

Double click on both of the devices in the device list in SmartRF Studio (

Figure

opening two windows, giving control of the two

radios at the same time.

Select one device to be the transmitter, by selecting the “Packet TX” tab shown in the

lower middle of

Figure

On the other device (the rec

eiver), select the “Packet RX” tab.

Set up basic test parameters and press the “Start

” button for the receiver.

Now you can start transmission by pressing the “Start” button for the transmitter.

The window

will show the number of packets sent on the transm

itter side and the

number of received packets and signal strength of the last received packet on the

receiver side.



Read and/or modify registers and common settings, such as RF frequency (or channel) and

output power.



Export RF register values in a user mo

difiable format by selecting “File



”.

SmartRF Studio

offers a lot of possibilities for testing and evaluating the hardware. Download the tool

and try it for yourself.

Otros manuales para CC2530 ZigBee Development Kit

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microcontrolador de Texas Instruments

Texas Instruments

Texas Instruments MSP430FG47x Manual de usuario

Texas Instruments

Texas Instruments MSP430F6720 Manual de usuario

Texas Instruments

Texas Instruments Chipcon CC2420DK Manual de usuario

Texas Instruments

Texas Instruments MUX36D04EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments DRV8251/AEVM Manual de usuario

Texas Instruments

Texas Instruments TPS929120EVM Manual de usuario

Texas Instruments

Texas Instruments Chipcon Products CC1110DK Manual de programación

Texas Instruments

Texas Instruments CC2540 Manual de usuario

Texas Instruments

Texas Instruments Errata MSP430F6746 Manual de usuario

Texas Instruments

Texas Instruments TMS320 2806 Series Manual del producto

Texas Instruments

Texas Instruments LaunchPad LAUNCXL-CC2650 Manual de usuario

Texas Instruments

Texas Instruments LaunchPad CC2650 Manual de usuario

Texas Instruments

Texas Instruments LP-MSPM0L1306 Manual de usuario

Texas Instruments

Texas Instruments CC-6LOWPAN-DK-868 Manual de usuario

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manual de usuario

Texas Instruments

Texas Instruments CDT370 Manual de usuario

Texas Instruments

Texas Instruments MSP430F6745 Manual de usuario

Texas Instruments

Texas Instruments LaunchPad MSP-EXP430F5529LP Manual de usuario

Texas Instruments

Texas Instruments TMS370 Series Guía del usuario

Texas Instruments

Texas Instruments SimpleLink MSP432E4 Manual del producto

Texas Instruments

Texas Instruments MSP430F6765 Manual de usuario

Texas Instruments

Texas Instruments DRV8311HEVM Manual de usuario

Texas Instruments

Texas Instruments MSPM0G310 Series Manual de usuario

Texas Instruments

Texas Instruments MSPM0G150 Series Manual de usuario

Manuales populares de Microcontrolador de otras marcas

AMS

AMS AS7261 Demo Kit Manual de usuario

Novatek

Novatek NT6861 Manual de usuario

Espressif Systems

Espressif Systems ESP8266 SDK Guía de configuración

Nuvoton

Nuvoton ISD61S00 ChipCorder Guía

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manual de usuario

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario

NEC

NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento

Mikroe

Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento

Intel

Intel Agilex Manual de usuario

Cypress

Cypress CY4607 HX2VL Manual de usuario

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manual de usuario

CYPRES

CYPRES CY14NVSRAMKIT-001 Manual de usuario

Espressif Systems

Espressif Systems ESP8266EX Instrucciones de funcionamiento

Abov

Abov AC33M8128L Manual de usuario

Laird

Laird BL654PA Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F800 Manual de usuario

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manual de usuario

Mikroe

Mikroe click Proximity 2 Manual de usuario