Texas Instruments CC1125 Manual de usuario

SWRU317A

March 2016

Web sites: www.ti.com/lprf

E2E Forum: www.ti.com/lprf-forum

Make sure to subscribe to the Low-Power RF

Newsletter to receive information about updates to

documentation, new product releases, and more.

CC1125 Development Kit Quick Start Guide

Opening the Box and Running the Packet Error Rate Test

1. Kit Contents

2 x SmartRF Transceiver Evaluation Boards

(TrxEB)

2 x CC1125 ETSI Cat1 868 MHz Boards

(CC1125EM-CAT1-868)

2 x W5017 Pulse Antennas

1 x MSP430 Debug Probe (FET)

2 x Micro USB Cables

1 x Standard USB Cable

1 x 14-pin Flat Cable

Documentation

2. TrxEB Overview

3. Plug the EM into the TrxEB

Insert a CC1125EM board into the TrxEB as

shown above. Connect the antenna to the SMA

connector on the EM.

Caution! The kit contains ESD sensitive

components. Handle with care to

prevent permanent damage.

The RF boards in this kit are tested and comply with

ETSI/R&TTE over temperature from 0 to +35°C. The

W5017 whip antenna from Pulse has a gain of 2 dBi.

The CC1125 is a receiver category 1 device, c.f. ETSI

EN 300 220-1, §4.1.1.

4. Select Board Mode

Use the switches S1 and S2 to select the

operating mode of the board. For the sake of this

quick start guide, please select “Enable” and

“UART”. This configuration will make it possible

to communicate directly with the MSP430 over a

virtual COM port on the PC.

5. Power Options

There are several ways of applying power to the

TrxEB.

2 x 1.5V AA Non-Rechargeable Alkaline

Batteries

USB (5V through USB plug)

External Power Supply (requirements below)

MSP430 Debug Probe

When the power source is batteries or USB, the

voltage regulators on the TrxEB will set the on-

board supply voltage to 3.3VDC.

External Power Supply1Requirements:

Nom Voltage: 3.3VDC

Max Current: 800 mA

Efficiency Level V

Warning! To minimize risk of personal injury or

property damage, never use rechargeable

batteries to power the board.

6. Select Power Source

Depending on the power source, make sure you

connect jumpers to the appropriate pins on the

“Power Source” header. For instance, if you use

batteries, use a jumper to short-circuit pin 1 and

2 on the header. The last jumper in the row (pin

9-10) should always be mounted, unless the

MSP430 FET is used as the power source.

Note that there should only be one active

power source at any one time. Do not leave

the board powered when unattended.

7. Welcome Screen

Turn on power with the Main Power switch. You

should now see the Texas Instruments logo and

a short description of the buttons on the LCD.

Pushing any of the five buttons on the board will

take you to the main menu.

NB! If you don’t see anything on the screen

make sure the mode switches are in the

correct positions (see step 4 above).

8. Packet Error Rate Test

Select the PER (Packet Error Rate) test by

highlighting the selection using the up/down

buttons. Confirm your selection by pressing

Enter (right button).

9. Select Test Mode

The PER test can be run is several modes. Easy

Mode sets up a one-way test and uses default

settings, which is convenient for range testing. To

proceed, highlight “Easy Mode” and press Enter

(right button).

The other test modes are described in the

“TrxEB RF PER Test Software Examples

User’s Guide”.

When using an external power supply, make sure it meets the listed requirements in addition to complying with applicable regional product regulatory and

safety certification requirements such as UL, CSA, VDE, CCC, and PSE.

Connectors

MSP430

Breakout

USB

Breakout

Main

Power

Switch

Power

Selection

Board Mode

Switches

LCD

Buttons

LEDs

MSP430

Debug

Probe

connector

10. Select Frequency

Select which frequency to use for the test. Make

sure that the evaluation modules you have

match the selected frequency.

11. Select Mode

One of the boards must operate as the slave

(transmitter) and the other as master (receiver).

Select Slave on one board…

…and Master on the other board.

12. Establish Link

The slave node will now wait for a configuration

package from the Master. The configuration

contains the parameters used for the PER test.

The configuration package will be sent when you

select “link devices” on the master node.

13. Link Established

When the initial linking has completed, the slave

node will start the test by continuously

transmitting packets to the master.

14. Start the Receiver (master)

On the master node, you can select the number

of packets you want to receive in order to

calculate the packet error.

When selecting “Start PER Test”, the master

(receiver) will begin to count the number of

received packets and provide some statistics.

15. PER Test Results

The master will display a window that plots the

received signal strength (RSSI) for each packet.

Press the “Up” button to go to the detailed

statistical window.

16. PER Test Results

The statistics window will show the error rate

based on the number of lost or erroneous

packets divided by the total number of packets

that should have been received.

17. Troubleshooting

It you are experiencing problems with this test,

please check the following:

Nothing is shown in the display! Make sure

the mode switches are in the correct

positions (see step 4 above).

Please visit the kit web page and check for

updated SW and documentation. Updated

SW can be downloaded to the device using

IAR Embedded Workbench for MSP430 or

SmartRF Flash Programmer.

If you get poor PER results at short

distances, try to move the transmitter and

receiver further apart. The CC1125 receiver

may be saturated if it is too close to the other

CC1125 transmitting at full output power.

18. References

Please visit www.ti.com and

http://www.ti.com/tool/cc1125dk

On the kit product page, you will find additional

documentation, links to updated software

examples and software tools like SmartRF

Studio.

You will also find a lot of information on the TI

E2E forum at http://e2e.ti.com

We hope that you will enjoy working with the

CC1125 device.

SmartRF™Studio

1. Download and Install

Before connecting SmartRF TrxEB to your PC,

download and install SmartRF Studio from

www.ti.com/smartrfstudio.

2. Launch SmartRF Studio

After installing the tool, connect the EB to the PC

using the USB cable and start SmartRF Studio.

Select the “Sub 1 GHz” tab and double click the

highlighted CC1125 device icon.

3. Test the Radio

You can now configure the radio, run

performance tests, export register settings and

run link tests with another CC1125 on a

SmartRF TrxEB connected to the PC.

IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES

Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,

reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are

developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you

(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of

this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources.

You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your

applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications

(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You

represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)

anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that

might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you

will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any

testing other than that specifically described in the published documentation for a particular TI Resource.

You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include

the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO

ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS.

TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT

LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF

DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,

COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR

ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your non-

compliance with the terms and provisions of this Notice.

This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.

These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation

modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Este manual sirve para los siguientes modelos

Otros manuales de Microcontrolador de Texas Instruments

Texas Instruments

Texas Instruments MSP430F67681 Manual de usuario

Texas Instruments

Texas Instruments Hercules TMS570LS31 Manual de usuario

Texas Instruments

Texas Instruments MSP430F6731A Manual de usuario

Texas Instruments

Texas Instruments AM243x Manual de usuario

Texas Instruments

Texas Instruments OMAP-L137/C6747 Manual de usuario

Texas Instruments

Texas Instruments MSP430F6775 Manual de usuario

Texas Instruments

Texas Instruments DRV8251/AEVM Manual de usuario

Texas Instruments

Texas Instruments TLC2543 Manual de usuario

Texas Instruments

Texas Instruments CC1120 Manual de usuario

Texas Instruments

Texas Instruments LaunchPad LAUNCXL-CC2650 Manual de usuario

Texas Instruments

Texas Instruments CC3220 Manual de usuario

Texas Instruments

Texas Instruments LaunchPad MSP430FR2476 Manual de usuario

Texas Instruments

Texas Instruments CC3100 SimpleLink Manual de usuario

Texas Instruments

Texas Instruments CC2652RSIP Manual de usuario

Texas Instruments

Texas Instruments CC3220 Manual de usuario

Texas Instruments

Texas Instruments Chipcon Products CC2420 Manual de usuario

Texas Instruments

Texas Instruments CC3235MODASF Manual de usuario

Texas Instruments

Texas Instruments ADC12DJ3200CVAL Manual de usuario

Texas Instruments

Texas Instruments Hercules TMS570LS31x Manual de usuario

Texas Instruments

Texas Instruments MSP430C311S Manual de usuario

Texas Instruments

Texas Instruments TMS570LS3137 Manual de usuario

Texas Instruments

Texas Instruments MSP43 series Manual de usuario

Texas Instruments

Texas Instruments MSP430F67671 Manual de usuario

Texas Instruments

Texas Instruments DLP Discovery 4100 Manual de usuario

Manuales populares de Microcontrolador de otras marcas

AMS

AMS AS7261 Demo Kit Manual de usuario

Novatek

Novatek NT6861 Manual de usuario

Espressif Systems

Espressif Systems ESP8266 SDK Guía de configuración

Nuvoton

Nuvoton ISD61S00 ChipCorder Guía

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manual de usuario

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario

NEC

NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento

Mikroe

Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento

Intel

Intel Agilex Manual de usuario

Cypress

Cypress CY4607 HX2VL Manual de usuario

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manual de usuario

CYPRES

CYPRES CY14NVSRAMKIT-001 Manual de usuario

Espressif Systems

Espressif Systems ESP8266EX Instrucciones de funcionamiento

Abov

Abov AC33M8128L Manual de usuario

Laird

Laird BL654PA Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F800 Manual de usuario

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manual de usuario

Mikroe

Mikroe click Proximity 2 Manual de usuario