TEUCER WP-2TW Manual de usuario
Teucer`s 2 zone touch panel allows users to control 2
separate zones of lighng from a single wall unit. Using a RF
signal to control the LED lighng, removes the need to have
addional wiring between the wall panel and the receiver,
which allows greater exibility during installaon by
reducing installaon me and cabling costs.
WP-2TW and LRR-WTC
2 zone RF & WIFI controller and receiver for single colour LED strip
Product Descripon
Technical Specicaon
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
Controller
Order Code WP-2TW
Type RF wall panel, WIFI transmier
Input Voltage 12-24VDC
Operaon Frequency 868MHz
Dimension 86x86x29mm (WxLxH)
Power 10W driver LD-IP10/24
Receiver
Order Code LRR-WTC
Type RF receiver
Input Voltage 12-36VDC
Current 4X5A
Output 4X(60-180)W
Note Constant voltage
Dimension 46x178x22mm (WxLxH)
• Smartphone / tablet compable via Easy Lighng app
• Wireless RF range of 8-15 meters (depending on signal
obstacles within the installaon area)
• Control 2 zones independently
• Touch sensive glass
• 5%-100% smooth dimming
• Backlit buons for night me use
Features
RF technology allows for greater exibility when it
comes to controlling simple or complex lighng instal-
laons without the need of addional cabling.
There are some limitaons where installaons have
the receivers enclosed in electrical boxes or hidden
away in a ceiling , reducing the RF signal strength and
therefore the communicaon range.
In order to overcome these RF Signal restricons we
suggest the following when synchronising our RF con-
trollers and receivers:
• Keep the distance within 10 meters from the con-
troller to the receiver
• When expanding your lighng, always try and use
a signal repeater (PR-RGB), where possible.
• If your installaon requires several RF receivers,
ensure the “master” receiver is posioned in the
middle.
Recommendaon
Receiver wiring diagram
Controller layout
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
When wiring the receivers, it is important to make sure the total waage of the LED strips does not exceed the maximum
rated waage per channel of the receiver. Each chanel is rated at 5A, so the maximum waage per channel is 24x5A=120w.
The power supply has to match the rated volrage and be superior to the toal LED strip waage by a remcommended 10%.
Zone 1 Zone 2
ON and
dim up bu�on
OFF and
dim down bu�on
GND Vin 12-24VDC
LN
1
23
LRR-WTC
Learning Key
4
MASTER SLAVE
L
N
110V-230VACPower Supply
1
23
LRR-WTC
Learning Key
4
MASTER SLAVE
L
N
110V-230VACPower Supply
WP-2TW and LRR-WTC
2 zone RF & WIFI controller and receiver for single colour LED strip
Synchronising the controller to receiver
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
1) Ensure the wall panel is connected to a power source
3) Ensure the receiver has power. Press the learning key on the receiver.
4) Touch the ON buon on the zone you wish to synchronise the receiver to. The LED strip
will blink twice to conrm synchronisaon.
6) To clear the receiver from a selected zone, simply press and hold the learning key for 5 or
more seconds. The receiver will be reset to the default factory sengs.
1
23
LRR-WTC
Learning Key
4
MASTER SLAVE
close circuit for MASTER
open circtuit for SLAVE
WP-2TW and LRR-WTC
2 zone RF & WIFI controller and receiver for single colour LED strip
2) Set the receiver LRR-WTC as a MASTER OR SLAVE.
Allocang the receiver as a master or slave is important to ensure your LED strip and receiv-
er are fully synchronised. There can be only 1 master receiver per zone.
1
23
LRR-WTC
Learning Key
4
MASTER SLAVE
Learning key
Zone 1 Zone 2
ON bu�on
5) Just repeat the learning process to synchronise several receivers to the same controller.
Teucer (UK) Ltd
Head oce
Bedford House, Fulham Green, Fulham High Street,
London, SW6 3JW, UK
Tel: +44 (0)20 7350 4429
Fax: +44(0)20 7228 4647
www.teucerled.co.uk
sales@teucer.eu
Logiscs Centre
Trident Court,
1 Oakcro Road,
Chessington,
Surrey, KT9 1BD, London, UK
Tel: +44(0)20 7350 4429, extension: 401
warehouse@teucer.eu
Controlling your LED strip
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
With WP-2WT you can adjust brightnes of single colour LED strip.
• Press to turn ON/OFF the desired zone.
• Press and hold ON buon to increase the
brightness of your chosen zone.
• Press and hold OFF buon to decrease
the brightness of your chosen zone.
WP-2TW and LRR-WTC
2 zone RF & WIFI controller and receiver for single colour LED strip
Zone 1 Zone 2
ON bu�on
Warranty
• Products must be installed and serviced by qualied
electrician.
• Please ensure the receiver is mounted in a water proof
enclosure if installed in an outdoor environment,
avoiding metallic enclosures.
• Always ensure products are mounted in areas with
adequate venlaon to avoid overheang.
• Please ensure outputs of any power suppliers used in
conjucon with this product comply with its working
voltage.
• Never install product whilst connected to power and
double check connecons before switching on to
avoid short circuits.
Safety
Should this product fail during the 3 year warranty
period it will be replaced free of charge, subject to the
correct installaon of the original product in accordance
with applicable and appropriate electrical codes and
instrucons provided by Teucer, as well as subsequent
return of the faulty unit. Teucer does not accept
responsibility for any installaon costs associated with
the replacement of this product and Teucer reserves the
right to alter specicaons without prior noce. Teucer
can oer 5 year warranty upon request. For further
informaon, please see our Terms and Condions.
www.teucerled.co.uk/terms-and-condions/
Este manual sirve para los siguientes modelos
1
Otros manuales de Receptor de TEUCER
