TerraTec Phono PreAmp Manual de usuario

Installation manual (English)

Version: 10.07.03

2 phono PreAmp Studio USB Installation (English)

phono PreAmp Studio USB Installation (English) 3

Installation Manual for Windows 98 SE

The phono PreAmp Studio USB does not need any special drivers to function. All it needs is

the standard USB drivers, which are an integrated component of the operating system. You

only have to carry out a couple of steps to begin using your phono PreAmp Studio USB right

away. If you have never used any USB devices on your system before, have your Windows 98

SE CD ready, because the installation might call for it.

Boot up your computer as usual. With the computer running, connect the provided cable into

your phono PreAmp Studio USB and then plug it into a USB port on your computer. With Win-

dows 98 SE, the “Add new Hardware Wizard” launches automatically and detects the new

hardware. Simply confirm by clicking “Next”.

Uncheck all of the locations suggested for searching for drivers (and do not select the Terratec

CD, since it does NOT contain any drivers). The operating system will locate the standard USB

driver independently of its location.

Various operating system files may have to be installed and, if so, you may be prompted to

insert your Windows installation CD into the drive. Insert the CD and continue by clicking

“Next”. You can run though all remaining steps by clicking “Next” and “Finish”. The device is

now ready to use.

You can verify whether the device was installed correctly in the “Device Manager”

(Start\Settings\Control Panel\System – Device Manager). The device is listed there twice:

once under “Sound, video and game controllers” and again under “Universal Serial Bus Con-

trollers”.

4 phono PreAmp Studio USB Installation (English)

There is just one more step necessary before you begin recording using your new phono Pre-

Amp Studio USB. Open the “Multimedia Properties” (Start\Settings\Control Panel – Multime-

dia) and select the USB audio device as the preferred recording device.

This step is necessary for recording with the phono PreAmp Studio USB. The Sound Rescue

software from Algorithmix included with the phono PreAmp Studio USB uses the preferred

recording device specified here. If at any time you wish to use your normal sound card for

recording, simply undo the change you made in this step. In doing so, there is no need to shut

down or reboot the computer.

phono PreAmp Studio USB Installation (English) 5

Installation Manual for Windows ME

The phono PreAmp Studio USB does not need any special drivers to function. All it needs is

the standard USB drivers, which are an integrated component of the operating system. You

only have to carry out a couple of steps to begin using your phono PreAmp Studio USB right

away.

Boot up your computer as usual. With the computer running, connect the cable provided into

your phono PreAmp Studio USB and then plug it into a USB port on your computer. With Win-

dows ME, the “Add new Hardware Wizard” launches automatically and detects the new hard-

ware. Simply confirm by clicking “Next”.

The operating system will locate the standard USB driver by itself. Various operating system

files may have to be installed and, if so, you may be prompted to insert your Windows instal-

lation CD into the drive. Insert the CD and continue by clicking “Next”. You can run though all

remaining steps by clicking “Next” and “Finish”. The device is now ready to use.

You can verify whether the device was installed correctly in the “Device Manager”

(Start\Settings\Control Panel\System – Device Manager). The device is listed there twice:

once under “Sound, video and game controllers” and again under “Universal Serial Bus Con-

trollers”.

There is just one more step necessary before you begin recording using your new phono Pre-

Amp Studio USB. Open the “Multimedia Properties” (Start\Settings\Control Panel – Multime-

dia) and select the USB audio device as the preferred recording device.

6 phono PreAmp Studio USB Installation (English)

This step is necessary for recording with the phono PreAmp Studio USB. The Sound Rescue

software from Algorithmix included with the phono PreAmp Studio USB uses the preferred

recording device specified here. If at any time you wish to use your normal sound card for

recording, simply undo the change you made in this step. In doing so, there is no need to shut

down or reboot the computer.

phono PreAmp Studio USB Installation (English) 7

Installation Manual for Windows 2000

The phono PreAmp Studio USB does not need any special drivers to function. All it needs is

the standard USB drivers, which are an integrated component of the operating system. You

only have to carry out a couple of steps to begin using your phono PreAmp Studio USB right

away.

Boot up your computer as usual. With the computer running, connect the cable provided into

your phono PreAmp Studio USB and then plug it into a USB port on your computer. The oper-

ating system registers the phono PreAmp Studio USB by itself.

You can verify whether the device was installed correctly in the “Device Manager”

(Start\Settings\Control Panel\System – Hardware - Device Manager). The device is listed there

twice: once under “Sound, video and game controllers” and again under “Universal Serial Bus

Controllers”.

There is just one more step necessary before you begin recording using your new phono Pre-

Amp Studio USB. Open the “Multimedia Properties” (Start\Settings\Control Panel – Sounds

and Multimedia - Audio) and select the USB audio device as the preferred recording device.

8 phono PreAmp Studio USB Installation (English)

This step is necessary for recording with the phono PreAmp Studio USB. The Sound Rescue

software from Algorithmix included with the phono PreAmp Studio USB uses the preferred

recording device specified here. If at any time you wish to use your normal sound card for

recording, simply undo the change you made in this step. In doing so, there is no need to shut

down or reboot the computer.

phono PreAmp Studio USB Installation (English) 9

Installation Manual for Windows XP

The phono PreAmp Studio USB does not need any special drivers to function. All it needs is

the standard USB drivers, which are an integrated component of the operating system. You

only have to carry out a couple of steps to begin using your phono PreAmp Studio USB right

away.

Boot up your computer as usual. With the computer running, connect the cable provided into

your phono PreAmp Studio USB and then plug it into a USB port on your computer. The oper-

ating system registers the phono PreAmp Studio USB by itself.

You can verify whether the device was installed correctly in the “Device Manager”

(Start\Settings\Control Panel - Switch to Classic View - System - Hardware - Device Manager).

The device is listed there twice: once under “Sound, video and game controllers” and again

under “Universal Serial Bus Controllers”.

There is just one more step necessary before you begin recording using your new phono Pre-

Amp Studio USB. Open the “Multimedia Properties” (Start\Settings\Control Panel - Switch to

Classic View - Sounds and Audio Devices – Audio) and select the USB audio device as the

preferred recording device.

10 phono PreAmp Studio USB Installation (English)

This step is necessary for recording with the phono PreAmp Studio USB. The Sound Rescue

software from Algorithmix included with the phono PreAmp Studio USB uses the preferred

recording device specified here. If at any time you wish to use your normal sound card for

recording, simply undo the change you made in this step. In doing so, there is no need to shut

down or reboot the computer.

Otros manuales para phono PreAmp

Tabla de contenidos

Otros manuales de Software de TerraTec

TerraTec

TerraTec Cinergy TV Manual de usuario

TerraTec

TerraTec MIDISmart Midi Keyboard Manual de usuario

TerraTec

TerraTec CAMEO DV800 Manual de usuario

TerraTec

TerraTec Cinergy Digital 2 Manual de usuario

TerraTec

TerraTec Advanced Standalone Mode Manual de usuario

TerraTec

TerraTec Algorithmix Sound Laundy Manual de usuario

TerraTec

TerraTec Cinergy TV Manual de usuario

TerraTec

TerraTec AudioSystem EWS 64 S Manual de usuario

TerraTec

TerraTec KOMPLEXER VST Manual de usuario

TerraTec

TerraTec Cinergy TV Manual de usuario

TerraTec

TerraTec ActiveRadio Manual de usuario

TerraTec

TerraTec AUREON 5.1 SKY Manual de usuario

TerraTec

TerraTec digitalXtension microWAVE PC Manual de usuario

TerraTec

TerraTec Cinergy Digital 3 Manual de usuario

Manuales populares de Software de otras marcas

COMPRO

COMPRO COMPROFM Manual de usuario

Muratec

Muratec OFFICEBRIDGE ONLINE Manual de usuario

Oracle

Oracle Contact Center Anywhere 8.1 Manual de usuario

Adobe

Adobe 65007312 - Photoshop Lightroom Manual

Avaya

Avaya NULL One-X for RIM Blackberry Manual de usuario

HP ProLiant BL420c Manual de usuario

PS Audio

PS Audio PowerPlay Manual del propietario

Brady

Brady LOCKOUT PRO 3.0 Manual de servicio

Avaya

Avaya Interaction Center Manual de usuario

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manual

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario

Oracle

Oracle Application 9i Manual de usuario

Acer

Acer RDM Manual de usuario

Canon

Canon Vixia HF21 Manual de usuario

Canon

Canon ZR950 Manual de usuario

Samsung

Samsung Auto Backup Manual de usuario

Polycom

Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manual de usuario

TerraTec phono PreAmp Manual de usuario

Manuales populares de Software de otras marcas