Tennant 6100E Manual de capacitación
IB 9018723 (04- 2019) 1
INSTRUCTION BULLETIN
No. 9018723
Machine: 6100E
Published: 04- 2019
Rev. 00
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the
Parts List in the appropriate place in the machine manual for future
reference. Retaining the Parts List will make it easier to reorder
individual parts and will save the cost of ordering an entire kit.
NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Installation instructions for kit number 9018722
SYNOPSIS:
This kit contains the parts needed to install the propel repair cable on 6100E sweepers.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: NONE
(Estimated time to complete: 1 hour)
PROTECT THE ENVIRONMENT
Please dispose of packaging materials, used machine components
such as batteries and fluids in an environmentally safe way according
to local waste disposal regulations.
Always remember to recycle.
PREPARATION:
FOR SAFETY: Before leaving or servicing
machine, stop on level surface, turn off
machine, and remove key.
1. Disconnect the battery cable from the
machine.
WARNING: Always disconnect battery
cables from machine before working on
electrical components.
2. Remove the left shroud from the machine and
set the shroud aside.
INSTALLATION:
1. Disconnect the main wire harness propel
leads from the controller M1 and M2
terminals. (Fig. 2/Fig. 3/Fig. 4)
2. Cut the connectors from the main wire
harness leads disconnected from the
controller and use electrical tape to secure the
leads back against the harness. Be sure all
exposed wire is completely covered with tape.
3. Disconnect the main wire harness from the
drive wheel assembly. (Fig. 2/Fig. 3/Fig. 5)
4. Cut the connectors from the main wire
harness leads disconnected from the drive
wheel assembly and use electrical tape to
secure the leads back against the harness.
Be sure all exposed wire is completely
covered with tape.
5. Connect the propel repair cable (1) to the
controller M1 and M2 terminals. (Fig. 2/
Fig. 3/Fig. 6)
IB 9018723 (04- 2019)2
6. Route the propel repair cable (1) along the
main wire harness and down to the drive
wheel assembly.
7. Connect the propel repair cable (1) to the
drive wheel assembly. (Fig. 2/Fig. 3/Fig. 6)
8. Use the cable ties (2) to secure the propel
repair cable (1) to the main wire harness.
9. If there is a cable clamp installed in the
location on the drive wheel adapter plate
shown in Fig. 1, remove and discard the cable
clamp. (Fig. 1)
10. Remove the cable clamp securing the main
wire harness to the extension spring
connected to the spring to the machine. Set
mounting hardware aside. Discard the cable
clamp (Fig. 1)
11. Use the cable clamp (3) to secure propel
repair cable (1) and main wire harness to the
extension spring attached to the frame of the
machine. (Fig. 1/Fig. 2)
12. Reinstall the left shroud onto the machine.
13. Reconnect the battery cable to the machine.
14. Start and test the machine. Operate the
machine in forward and reverse. Ensure the
propel repair cable (1) is completely secured
to the main wire harness and cannot become
caught in any moving parts.
FIG. 1
IB 9018723 (04- 2019) 3
Disconnect main
wire harness
connections from
drive wheel
assembly
Disconnect main wire harness
connections from controller M1
and M2 terminals
Electrical panel
on rear lintel
Frame of
machine
Remove and discard
cable clamp. Replace
with cable clamp (3)
Extension spring
connected to frame
of machine
Drive wheel
adapter plate
FIG. 2
IB 9018723 (04- 2019)4
FIG. 3
IB 9018723 (04- 2019) 5
FIG. 4
IB 9018723 (04- 2019)6
FIG. 5
FIG. 6
Bill Of Materials For Propel Cable, Repair, Afmkt [6100] - 9018722
Ref.
Tennant
Part No. Description Qty.
11076611 )Cable, Ele [6100, Propel, 8GA, Repair] 1
2 49266 Tie, Cable, Nyl, 07.3L .19W 1.8 Max D 12
367767 Clamp, Cable, Stl, 0.69D X 0.62W, 1Hole 1
TENNANT COMPANY
P. O. Box 1452
Minneapolis, MN 55440-1452
Otros manuales para 6100E
2
Otros manuales de Soplador de Tennant
Tennant
Tennant A60 Manual de usuario
Tennant
Tennant S6 Manual de usuario
Tennant
Tennant 6100 Manual de capacitación
Tennant
Tennant S6+ Manual de usuario
Tennant
Tennant 614214 Manual del producto
Tennant
Tennant 340429 Manual de capacitación
Tennant
Tennant 6500 Manual de usuario
Tennant
Tennant S20 Gas Manual de usuario
Tennant
Tennant 365 Manual de usuario
Tennant
Tennant S5 NA Manual del producto
Tennant
Tennant SweepSmart S20 ELECTRIC Manual de usuario
Tennant
Tennant SweepSmart S20 ELECTRIC Manual de usuario
Tennant
Tennant S5 Manual de usuario
Tennant
Tennant S12 Manual de usuario
Tennant
Tennant SweepSmart S20 ELECTRIC Manual de capacitación
Tennant
Tennant SweepSmart S20 ELECTRIC Instrucciones de funcionamiento e instalación
Tennant
Tennant M17 Series Manual de capacitación
Tennant
Tennant 800 Manual de usuario
Tennant
Tennant SweepSmart S20 ELECTRIC Manual de usuario
Tennant
Tennant 3640E Manual de usuario
