Teltonika FMP100 Manual de usuario
https://wiki.teltonika-gps.com/view/FMP100_First_Start
FMP100 First Start
Main Page > Fast & Easy Trackers > FMP100 > FMP100 First Start
An easy Plug and Track real-time tracking terminal with GNSS, GSM and Bluetooth
connectivity
Contents
1 Know your device
2 Set up your device
2.1 How to insert Micro-SIM card and connect the battery
2.2 PC Connection (Windows)
2.3 How to install USB drivers (Windows)
2.4 Configuration (Windows)
2.5 Quick SMS configuration
3 Safety information
3.1 Precautions
Know your device
Set up your device
How to insert Micro-SIM card and connect the battery
Insert the SIM tray removal tool into the hole on the SIM card tray and then push until the1.
tray pops out.
Split device cover to access battery connector inside.2.
Connect the battery as shown to device.3.
Gently close device cover back.4.
Insert Nano-SIM card as shown with PIN request disabled or read our Wiki how to enter it5.
later in Teltonika Configurator. Make sure that Nano-SIM card is fitted properly into the tray.
Insert the SIM card tray back.6.
After configuration, see see PC Connection (Windows).7.
Device is ready to be mounted.
Nano-SIM card insertion/removal must be performed when device is powered off –
external voltage and battery are disconnected. Otherwise Nano-SIM card might be
damaged or device will not detect it.
PC Connection (Windows)
FMP100 device can be connected to PC for configuration in two different ways:
DC with Bluetooth1.
Power-up FMP100 with DC voltage 10-30 V power supply using supplied power1.
cable. LED’s should start blinking, see “FMP100 LED status”.
FMP100 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select2.
Add Bluetooth or other device > Bluetooth. Choose your device named –
“FMP100_last_7_imei_digits”, without LE in the end. Enter default password 5555,
press Connect and then select Done.
With Micro-USB cable2.
Remove SIM tray1.
Remove TOP cover2.
Insert the SIM card into SIM tray3.
Insert SIM Tray into device4.
Connect Micro-USB cable to device and connect to computer USB port. LED’s should5.
start blinking, see “FMP100 LED status”.
First time you will need to install USB drivers, see "How to install USB drivers (Windows)"
GSM signal will not be available and device will not open GPRS because TOP casing part is
removed and GSM antenna is inserted into TOP casing part.
How to install USB drivers (Windows)
Please download COM port drivers from Teltonika here.1.
Extract and run TeltonikaCOMDriver.exe.2.
Click Next in driver installation window.3.
In the following window click Install button.4.
Setup will continue installing the driver and eventually the confirmation window will appear.5.
Click Finish to complete the setup.
Configuration (Windows)
At first FMP100 device will have default factory settings set. These settings should be changed
according to the user's needs.
Main configuration can be performed via Teltonika Configurator software. Get the latest FMP100
Configurator version from here. Configurator operates on Microsoft Windows OS and uses
prerequisite MS .NET Framework. Make sure you have the correct version installed.
MS .NET requirements
Operating
system
MS .NET
Framework
version
Version Link
• Windows
Vista
• Windows
7
• Windows
8.1
• Windows
10
MS .NET
Framework
4.6.2
32 and
64 bit
www.microsoft.com
Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe.
After launch software language can be changed by clicking in the right bottom corner:
Configuration process begins by pressing on connected device:
After connection to Configurator Status window will be displayed:
Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc.
FMP100 has one user editable profile, which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to device using Save to device button.
Main buttons offer following functionality:
Load from device – loads configuration from device.1.
Save to device – saves configuration to device.2.
Load from file – loads configuration from file.3.
Save to file – saves configuration to file.4.
Update firmware – updates firmware on device.5.
Read records – read records from device.6.
Reboot device – restarts device.7.
Reset configuration – sets device configuration to default.8.
Most important configurator section is GPRS – where all your server and GPRS settings can be
configured and Data Acquisition – where data acquiring parameters can be configured. More
details about FMP100 configuration using Configurator can be found here.
Quick SMS configuration
Default configuration has optimal parameters present to ensure best performance of track quality
and data usage.
Quickly set up your device by sending this SMS command to it:
" setparam
2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0"
GPRS settings:
2001 – APN
2002 – APN username (if there are no APN username, empty field should be left)
2003 – APN password (if there are no APN password, empty field should be left)
Server settings:
2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)
Note: Before SMS text, two space symbols should be inserted.
Default configuration settings
Movement and ignition detection:
Vehicle movement will be detected
by accelerometer
Ignition will be detected by
vehicle power voltage
between 13,2 – 30 V
Device makes a record On Moving if one of these events happen:
300 seconds passes Vehicle turns 10° degrees
Vehicle drives 100 meters
Speed difference between
last coordinate and current
position is greater than 10
km/h
Device makes a record On Stop if:
1 hour passes while vehicle is
stationary and ignition is off
Records sending to server:
If device has made a record it is
sent to the server every 120
seconds
After successful SMS configuration, FMP100 device will synchronize time and update records to
configured server. Time intervals and default I/O elements can be changed by using Teltonika
Configurator or SMS parameters.
Safety information
This message contains information on how to operate FMP100 safely. By following these
requirements and recommendations, you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating the device!
The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed
voltage range is +10..+30V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package.
Before usage, the device should be placed so that its LED indicators are visible. They show the
status of device operation.
Before unmounting the device from the vehicle, ignition MUST be OFF.
Precautions
Do not disassemble the device. If the device is damaged, the power supply cables are
not isolated or the isolation is damaged, DO NOT touch the device before unplugging
the power supply.
All wireless data transferring devices produce interference that may affect other
devices which are placed nearby.
Please consult representatives of your vehicle model regarding OBD II location on your
vehicle. In case you are not sure about proper connection, please consult qualified
personnel.
The programming must be performed using a PC with autonomic power supply.
The device is susceptible to water and humidity.
Installation and/or handling during a lightning storm is prohibited.
Teltonika is not responsible for any harm caused by wrong cables used for connection
between PC and FMP100.
WARNING! Do not use FMP100 device if it distracts driver or causes inconvenience due
to OBD II placement. Device must not interfere with driver.
https://teltonika.lt/product/FMP100/
Otros manuales para FMP100
4
Tabla de contenidos
Otros manuales de GPS de Teltonika
Teltonika
Teltonika TMT250 Manual de usuario
Teltonika
Teltonika FMB225 Manual de usuario
Teltonika
Teltonika GH1200 Manual de usuario
Teltonika
Teltonika FMB130 Guía de instalación
Teltonika
Teltonika FMB020 Guía de instalación
Teltonika
Teltonika FMB900 Manual de usuario
Teltonika
Teltonika FMB910 Guía de instalación
Teltonika
Teltonika TFT100 Guía de instalación
Teltonika
Teltonika FMB003 Guía de instalación
Teltonika
Teltonika Telematics FMM650 Guía de instalación
Teltonika
Teltonika Telematics FMC003 Manual de usuario
Teltonika
Teltonika FM640 Manual de usuario
Teltonika
Teltonika FM1200 Manual de usuario
Teltonika
Teltonika FMB202 Guía de instalación
Teltonika
Teltonika FMB630 Manual de usuario
Teltonika
Teltonika FMM920 Guía de instalación
Teltonika
Teltonika FMB003 Guía de instalación
Teltonika
Teltonika TMT250 Guía de instalación y uso
Teltonika
Teltonika FMB965 Guía de instalación
Teltonika
Teltonika FMB208 Guía de instalación
