Teltonika AT1000 Manual de usuario

AT1000 Quick Start Guide

V1.0

1INTRODUCTION

AT1000 is a terminal with GPS and GSM connectivity, which is able to determine the object’s

coordinates and transfer them via the GSM network. This device is perfectly suitable for applications

where location acquirement of remote objects is needed. Device operates using internal batteries only

and its main applications are tracking of objects which do not have onboard power supply.

1.1 Attention

Personal or portable computers to be connected to the device

must comply with the requirements of DIN EN 60950-1.2003.

Do not disassemble the device more than it is allowed. If the

device is damaged, the power supply cables are not isolated or

the isolation is damaged, before unplugging the power supply, do

not touch the device.

All wireless data transferring devices produce interference that

may affect other devices which are placed nearby.

The device may be fitted only by qualified personnel.

The device must be firmly fastened in the predefined location.

The programming must be performed using a second class PC

(with autonomic power supply).

The device is susceptible to water and humidity in environment

with IP class greater than IP65.

Use only batteries provided by Teltonika. If wrong battery is

used, the device may malfunction. Teltonika takes no

responsibility for device damage caused by third party batteries.

Any installation and/or handling during a lightning storm is

prohibited.

Please use cables provided with AT1000 device.

Teltonika is not responsible for any harm caused by using wrong

cables for PC <-> AT1000 connection.

Teltonika reserves the right to change or modify the device in a

way that feels is acceptable and is not in disagreement with terms

and conditions.

Ensure that the batteries are not immersed in water. When

stored, keep the device in a cool and dry place.

Ensure that device and batteries are not exposed to hot surfaces

or direct sunlight.

When transporting, ensure that batteries are safe from metal

articles and do not keep it with metal rings, chains, etc.

Do not damage battery with sharp objects.

Do not try to charge the battery – this may lead to explosion

and/or other harms.

1.2 Instructions of safety

This chapter contains information on how to operate AT1000 safely. By following these

requirements and recommendations, you will avoid dangerous situations. You must read these

instructions carefully and follow them strictly before operating the device!

The device uses a 5V...7.2V DC batteries.

To avoid mechanical damage, it is advised to transport the AT1000 device in an impact-proof

package.

The device is designed to be mounted in a zone of limited access. All related devices must meet

the requirements of standard EN 60950-1.

1.3 Legal Notice

of part or all of the contents in this document in any form without the prior written permission of

Teltonika is prohibited.

Other products and company names mentioned here may be trademarks or trade names of their

respective owners.

1.4 Package contents

The AT1000 device is supplied to the customer in a cardboard box containing all the equipment

that is necessary for operation. The package contains:

1. The AT1000 device.

2. Micro USB cable.

3. 2 x 3.6V batteries

4. AT1000 drivers download link paper

2PREPARATION

2.1 Software requirements

Windows XP with SP2 or later, Windows Vista

MS .NET Framework V3.5 or later (http://www.microsoft.com or

http://avl1.teltonika.lt/downloads/tavl/Framework/dotnetfx35setupSP1.zip).

2.2 Drivers

Please download Virtual COM Port drivers from Teltonika website:

http://avl1.teltonika.lt/downloads/AT1000/vcpdriver_v1.1_setup.zip.

IMPORTANT: AT1000 must be connected to PC when installing drivers!

3PREPARATION OF THE DEVICE



 

 

 Open AT1000 device

 REMOVE INULATING TAPES

 Open SIM card lid and insert the SIM card

 Close SIM card lid

 Push SIM card lid in the shown direction to lock it and assemble AT1000

4Connecting AT1000 to PC

Figure 1. Connecting micro USB cable to AT1000

When AT1000 is connected for the first time to PC, you will be prompted with 'Found New

Hardware' window. Click 'Cancel' to stop automatic installation process.

Figure 2. Found New Hardware window

Extract and launch VCPDriver_V1.1_Setup.exe. This driver is used to detect AT1000 device

connected to the computer. Click 'Next' in driver installation window.

Figure 3. Driver installation window

Installation wizard will prompt you with several windows telling that software did not pass

Windows Logo test. Click 'Continue Anyway' button to continue.

Figure 4. Windows Logo pass window

Setup will continue installing drivers and will display a window about successful process in the

end. Click 'Finish' to complete setup.

Figure 5. Successful installation window

Note: if drivers did not install successfully or device is not recognized, please make sure that

device is connected to PC and reinstall the drivers.

5Batteries

AT1000 is autonomous device which uses two R14 (ANSI standard) batteries. Batteries used in

this device are single charge Li based type and should have the following parameters:

Voltage: 3.6V

Nominal capacity:5500mAh

Max pulse current not less than:2000mA

Teltonika recommended batteries are available for sale from Teltonika office or distributors.

Only with these batteries correct device operation and (or) prevention of permanent damage to device

is guaranteed.

Warning: use only the same sort of batteries in pair and do not mix old batteries with new ones.

Note:

if inserting the batteries for the first time, make sure insulating tape is

removed! In order to not discharge batteries, please remove them when not using the

device.

6Configurator

AT1000 Configurator is software used to setup the device. You can save or read the settings

and read modem IMEI number with it. Please download latest version of AT1000 Configurator from

Teltonika webpage: http://avl1.teltonika.lt/downloads/AT1000/.

To use Configurator with AT1000, make sure that batteries are inserted in the device and it is

connected to PC. In the configurator please choose correct COM port used by device. To find out

which COM port is used follow these steps:

Right-click on 'My Computer' and choose 'Properties';

Go to 'Hardware' and click on 'Device Manager';

Expand 'Ports (COM & LPT)' menu. See COM port number near 'STM Virtual COM

Port'.

Figure 6. STM Virtual COM Port number

7CONFIGURATION

Main AT1000 Configurator windows consist of three parts: operations menu (1), global

parameters settings (2) and profiles parameters settings(3).

Figure 7. Main AT1000 Configurator window

7.1 Operations menu

This is a list of commonly used operations such as:

Defaults: choose one of 3 available default settings for the device. Every time you launch

Configurator software, you either have to load settings from file, or load default settings and

modify values manually.

Load from file: click this button to load device settings from file so you don't have to enter

them by hand every time you want to configure the device.

Save to File: click this button to save manually entered setting to a file.

Read from flash: reads settings that are already stored in AT1000 device.

Write to flash: saves the settings to AT1000 memory. Note, that you have to load these settings

from file or enter them manually first.

Get IMEI: reads AT1000 modem IMEI (International Mobile Equipment Identity) number.

Note, that after you connect device to power supply, it takes several seconds to load modem –

only then Configurator is able to read it. Otherwise it will be displayed as 'none'.

COM port: click this drop-down list to choose which COM port is used by AT1000 to connect

to PC. See chapter 6 to find out number of the port.

Refresh button: click it to refresh all available ports on PC. This button is used when you

connect AT1000 to PC while Configurator software is already launched, but it did not detect

Virtual COM Port yet.

Otros manuales para AT1000

Tabla de contenidos

Otros manuales de GPS de Teltonika

Teltonika

Teltonika Telematics FTC921 Manual de usuario

Teltonika

Teltonika FM1110 Manual de usuario

Teltonika

Teltonika GH120 Series Manual de instrucciones

Teltonika

Teltonika FM5300 Manual de usuario

Teltonika

Teltonika FMM00A Guía de instalación

Teltonika

Teltonika GH5200 Manual de usuario

Teltonika

Teltonika FM3622 Manual de usuario

Teltonika

Teltonika FMB010 Manual de usuario

Teltonika

Teltonika FMM800 Guía de instalación

Teltonika

Teltonika FMB225 Guía de instalación

Teltonika

Teltonika GH4000 Manual de usuario

Teltonika

Teltonika Telematics FTC881 Manual de usuario

Teltonika

Teltonika FMB230 Manual de usuario

Teltonika

Teltonika FMC130 Manual de usuario

Teltonika

Teltonika TFT100 Guía de instalación

Teltonika

Teltonika FMC234 Manual de usuario

Teltonika

Teltonika GH4000 Manual de usuario

Teltonika

Teltonika GH5200 Manual de usuario

Teltonika

Teltonika FMP100 Manual de usuario

Teltonika

Teltonika FMB002 Manual de usuario

Teltonika

Teltonika FMB122 Manual de usuario

Teltonika

Teltonika FMM640 Guía

Teltonika

Teltonika FMB001 Manual de usuario

Teltonika

Teltonika FMB125 Guía de instalación

Manuales populares de GPS de otras marcas

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Manual de usuario

Garmin

Garmin SOUNDER 125 Manual de usuario

Garmin

Garmin DEZL 580 Manual de usuario

Jigabot

Jigabot EX Manual de usuario

Pointer

Pointer Cellocator CelloTrack XT LTE Guía de instalación

Queclink

Queclink GV55LITE Manual de usuario

Voxson

Voxson Voxtrack GPS500 Manual de instrucciones

Garmin

Garmin ECHOMAP PLUS Manual de usuario

Starcom Systems

Starcom Systems Kylos Compact Manual de usuario

Garmin

Garmin 15 H Series Manual de usuario

Cobra

Cobra Marine MC 600Ci Manual de usuario

Cellocator

Cellocator CelloTrack T Manual de usuario

Enfora

Enfora Mini-MT GSM2228UG001 Manual de usuario

Magellan

Magellan eXplorist 100 Manual de usuario

LTE

LTE G50B Manual de usuario

Garmin

Garmin DEZL OTR500 Manual de usuario

SkyGolf

SkyGolf SkyCaddie SG1 Manual de usuario