Teledyne T101 Manual de usuario

OPERATION MANUAL

MODEL T101

UV FLUORESCENCE H2S ANALYZER

TELEDYNE MONITOR LABS

35 INVERNESS DRIVE EAST

ENGLEWOOD, CO 80112

USA

Toll-free Phone:

800-846-6062

Phone:

303-792-3300

Fax:

Spare Parts:

Repairs:

303-799-4853

800-934-2319

800-324-5190

Email:

tml_support@teledyne.com

Website:

http://www.teledyne-ml.com/

072660000 Rev. B

Teledyne Monitor Labs

May 2016

NOTICE OF COPYRIGHT

TRADEMARKS

All trademarks, registered trademarks, brand names or product names appearing

in this document are the property of their respective owners and are used herein

for identification purposes only.

This page intentionally left blank.

iii

SAFETY MESSAGES

Important safety messages are provided throughout this manual for the purpose of

avoiding personal injury or instrument damage. Please read these messages

carefully. Each safety message is associated with a safety alert symbol. They are

placed throughout this manual. The safety symbols are also located inside the

instrument. It is imperative that you pay close attention to these messages, the

descriptions of which are as follows:

WARNING: Electrical Shock Hazard

HAZARD: Strong oxidizer

GENERAL WARNING/CAUTION: Read the accompanying

message for specific information.

CAUTION: Hot Surface Warning

Do Not Touch: Touching some parts of the instrument

without protection or proper tools could result in damage to the

part(s) and/or the instrument.

Technician Symbol: All operations marked with this symbol

are to be performed by qualified maintenance personnel only.

Electrical Ground: This symbol inside the instrument marks

the central safety grounding point for the instrument.

CAUTION

This instrument should only be used for the purpose

and in the

manner described in this manual. If you use this instrument

in a

manner other than that for which it was int

ended, unpredictable

behavior could ensue with possible hazardous consequences.

NEVER use any gas analyzer to sample combustible gases!

Note

For Technical Assistance regarding the use and maintenance of this instrument or any other

Teledyne ML product, contact Teledyne ML’s Technical Support Department:

Telephone: 800-846-6062

Email: tml_support@teledyne.com

or access any of the service options on our website at http://www.teledyne-ml.com/

CONSIGNESDE SÉCURITÉ

Des consignes de sécurité importantes sont fournies tout au long du présent

manuel dans le but d’éviter des blessures corporelles ou d’endommager les

instruments. Veuillez lire attentivement ces consignes. Chaque consigne de

sécurité est représentée par un pictogramme d’alerte de sécurité; ces

pictogrammes se retrouvent dans ce manuel et à l’intérieur des instruments. Les

symboles correspondent aux consignes suivantes :

AVERTISSEMENT : Risque de choc électrique

DANGER : Oxydant puissant

AVERTISSEMENT GÉNÉRAL / MISE EN GARDE : Lire la consigne

complémentaire pour des renseignements spécifiques

MISE EN GARDE : Surface chaude

Ne pas toucher : Toucher à certaines parties de l’instrument sans

protection ou sans les outils appropriés pourrait entraîner des

dommages aux pièces ou à l’instrument.

Pictogramme « technicien » : Toutes les opérations portant ce

symbole doivent être effectuées uniquement par du personnel de

maintenance qualifié.

Mise à la terre : Ce symbole à l’intérieur de l’instrument détermine le

point central de la mise à la terre sécuritaire de l’instrument.

MISE EN GARDE

Cet instrument doit être utilisé aux fins décrites et de la manièr

décrite dans ce manuel. Si vous utilisez cet instrument d’une

autre manière que celle pour laquelle il a été prévu, l’instrument

pourrait se comporter de façon imprévisible et entraîner des

conséquences dangereuses.

NE JAMAIS utiliser un analyseur de gaz pour échantillonner des

gaz combustibles!

WARRANTY

WARRANTY POLICY (02024 F)

Teledyne Monitor Labs (TML), a business unit of Teledyne Instruments, Inc.,

provides that:

Prior to shipment, TML equipment is thoroughly inspected and tested. Should

equipment failure occur, TML assures its customers that prompt service and support

will be available.

COVERAGE After the warranty period and throughout the equipment lifetime, TML stands ready

to provide on-site or in-plant service at reasonable rates similar to those of other

manufacturers in the industry. All maintenance and the first level of field

troubleshooting are to be performed by the customer.

NON-TML MANUFACTURED EQUIPMENT

Equipment provided but not manufactured by TML is warranted and will be repaired

to the extent and according to the current terms and conditions of the respective

equipment manufacturer’s warranty.

Product Return All units or components returned to Teledyne ML should be properly packed for

handling and returned freight prepaid to the nearest designated Service Center.

After the repair, the equipment will be returned, freight prepaid.

The complete Terms and Conditions of Sale can be reviewed at

http://www.teledyne-ml.com/terms_and_conditions.asp

CAUTION – Avoid Warranty Invalidation

Failure to comply with proper anti-Electro-Static Discharge (ESD) handling and packing

instructions and Return Merchandise Authorization (RMA) procedures when returning

parts for repair or calibration may void your warranty. For anti-

ESD handling and

packing instructions please refer to “Packing Components for Return to Teledyne ML” in

the Primer on Electro-Static Discharge section of this manual, and for RMA procedures

please refer to our Website at http://www.teledyne-ml.c om under Customer Support >

Return Authorization.

This page intentionally left blank.

Tabla de contenidos

Otros manuales de Instrumento de medición de Teledyne

Teledyne

Teledyne Mixchek Manual de usuario

Teledyne

Teledyne TED 191 Manual de usuario

Teledyne

Teledyne 2010B Manual de usuario

Teledyne

Teledyne N500 Manual de usuario

Teledyne

Teledyne 465M Manual de usuario

Teledyne

Teledyne T200U Instrucciones de instalación y funcionamiento

Teledyne

Teledyne HASTINGS HFM-300 Manual de usuario

Teledyne

Teledyne 440 Guía del usuario

Teledyne

Teledyne T3LCR1002 Manual de usuario

Teledyne

Teledyne HVG-2020A Manual de usuario

Teledyne

Teledyne SeaBat T Series Manual de usuario

Teledyne

Teledyne BENTHOS UDB-9000 Manual de usuario

Teledyne

Teledyne GFC7000EU Manual de usuario

Teledyne

Teledyne 9110AH Manual de usuario

Teledyne

Teledyne T3SP Series Manual de usuario

Teledyne

Teledyne CEA 9001 Manual de usuario

Teledyne

Teledyne HVG-2020B Manual de usuario

Teledyne

Teledyne T3LCR1002 Manual de usuario

Teledyne

Teledyne ADFM Pro20 Instrucciones de funcionamiento

Teledyne

Teledyne First Responder CG Manual de instrucciones

Teledyne

Teledyne AX300 Manual de usuario

Teledyne

Teledyne 6600 Manual de usuario

Teledyne

Teledyne IsoPlane SCT-320 Manual de usuario

Teledyne

Teledyne 2120XL Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario