Teledyne GB300 Manual de usuario

The Quick Start Guide describes the steps to successfully start, calibrate, and use the GB300 instrument.

Components

The GB300 Portable Oxygen Analyzer includes:

•Instrument and carrying case

•I-17 sensor

•Sensor interconnection cable

•T adapter P/N A268

•Barbed hose adapter P/N F1717

•3 AA batteries

•Quick Start Manual

Optional items:

•RS232 digital output

•Interface cable: 0-1 vdc P/N B75554

•Interface cable: RS232 P/N B75555

Set Up

Set up is simple:

1. Install the cable and sensor

2. Install 3 AA alkaline batteries.

3. Calibrate

Cable and Sensor Assembly

1. Insert the coiled cable connector into the right side of the instrument and secure the locking nut.

2. Remove the sensor from its protective package. Caution: If you see signs of moisture or liquid

in the protective bag do not open the package. Sensor contains caustic, which causes severe

burns and may be fatal if swallowed. The Material Safety Sheet can be found in the service

section of our web site at <www.teledyne-ai.com>

3. Connect the coiled cable to the sensor and secure the locking nut.

M-GB300-REV 2

Battery Installation

1. Hold the instrument face down.

2. Using a coin, gently twist to open the

hinged battery compartment door

latch.

3. Lift up door near latch and pull out.

4. Install 3 AA alkaline batteries

observing proper polarity.

Note: Use only alkaline batteries

Quick Start Guide for Model GB300 Portable Oxygen Analyzer

REV 2

Calibration

1. After installing the batteries and sensor the LCD will

read 00.0 and the battery indicator will show a full

charge with all bars activated. On initial start up with a

new sensor, allow the unit to stabilize for about 10

minutes before proceeding to the next step.

2. With the sensor exposed to room air or 100% oxygen,

press and hold the ON/OFF key down until the LCD

starts to count from 3 to 0. Release the key as soon as the

count starts and wait for the LCD to read 20.9 plus or

minus a few percent. Note: Holding ON/OFF key down

during the automatic calibration sequence will shut the

unit off when released. Excluding factors such as

temperature, humidity, and trace amounts of other gases,

the air we breathe contains 20.9% oxygen (calibration

point) and 79.1 % nitrogen. Subsequent calibrations

require that you first turn the unit on by pressing the ON/OFF key once. When the LCD

displays a value, press and hold the ON/OFF key until the LCD starts to count down as

noted above.

Gas Sampling

For flowing gas applications use the supplied adapter P/N C53790. When sampling, do not

pressurize the sensor as this will lead to incorrect readings. The sensor is a partial pressure device.

Any change in pressure from the calibration point will affect the reading.

Turning the Unit OFF

Press and release the ON/OFF key.

Specifications:

Range: 0-100% oxygen

Response time: 90% of final value in less than 10 seconds.

Sensor life: 36 months in air.

Battery life: Approximately 2000 hours.

Power: 3 AA alkaline batteries

Standard Output: 0-1 vdc.

Operating Temperature: 0-40 ˚C

Warranty: One (1) year against defects in material and workmanship.

M-GB300-REV 2

Tabla de contenidos

Otros manuales de Instrumento analítico de Teledyne

Teledyne

Teledyne 3000ZA2G Manual de usuario

Teledyne

Teledyne T802 Manual de usuario

Teledyne

Teledyne 3020T Manual de usuario

Teledyne

Teledyne 3000MA Manual de usuario

Teledyne

Teledyne 3010TAC Manual de usuario

Teledyne

Teledyne 310 Manual de usuario

Teledyne

Teledyne 5000B Manual de usuario

Teledyne

Teledyne 327RACEU Manual de usuario

Teledyne

Teledyne 306WA Manual de usuario

Teledyne

Teledyne 4060 Series Manual de lista de piezas

Teledyne

Teledyne 6000A Manual de usuario

Teledyne

Teledyne 311PC Manual de usuario

Teledyne

Teledyne 311 Manual de usuario

Teledyne

Teledyne 3500 Series Manual de usuario

Teledyne

Teledyne 7500 Series Manual de usuario

Teledyne

Teledyne 311XL Series Manual de usuario

Teledyne

Teledyne 3000MB Manual de usuario

Teledyne

Teledyne BDS-3960 Manual de usuario

Teledyne

Teledyne BDS 3000 Manual de usuario

Teledyne

Teledyne 9060 Manual de instrucciones

Teledyne

Teledyne TED 60-T Manual de usuario

Teledyne

Teledyne EV71YC1MCL2010-BA0 Manual de usuario

Teledyne

Teledyne 4040 Manual de lista de piezas

Teledyne

Teledyne 7120 Manual de usuario

Manuales populares de Instrumento analítico de otras marcas

Cocraft

Cocraft NLT04 Manual de usuario

M&C

M&C GENTWO PMA1000 Manual de usuario

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Manual de usuario

CONDTROL

CONDTROL XP4 PRO Manual de usuario

Extech Instruments

Extech Instruments BR200 Manual de usuario

Dewetron

Dewetron DEWE-30-16 Manual del producto

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Instrucciones de instalación y funcionamiento

RIDGID

RIDGID SeeSnake Compact Manual de usuario

YDLIDAR

YDLIDAR TIA Manual de usuario

Olympus

Olympus IPLEX FX Series Manual de usuario

Bosch

Bosch GLM 50 C Professional Manual de usuario

Reflecta

Reflecta DigiEndoscope Manual de usuario

Chinavision

Chinavision CVACZ-G696 Instrucciones de montaje

Fuji Electric

Fuji Electric ZKMA Manual de usuario

VOLTCRAFT

VOLTCRAFT IC-100HD Manual de usuario

RIDGID

RIDGID micro CA-25 Manual de usuario

Würth

Würth MASTERVISION MINI REC Manual de usuario

AMI

AMI 2001LC Manual de usuario