Teledyne Lecroy PP016 Manual de usuario

Operator’s

Manual

PP0

16 Passive Probe

Unauthorized duplication of Teledyne LeCroy documentation materials is

strictly prohibited. Customers are permitted to duplicate and distribute

Teledyne LeCroy documentation for internal educational purposes.

Teledyne LeCroy is a registered trademark of Teledyne LeCroy, Inc. Other

product or brand names are trademarks or requested trademarks of their

respective holders. Information in this publication supersedes all earlier

versions. Specifications are subject to change without notice.

Warranty

Teledyne LeCroy warrants this oscilloscope accessory for normal use and

operation within specification for a period of one year from the date of shipment.

Spare parts, replacement parts and repairs are warranted for 90 days.

In exercising its warranty, Teledyne LeCroy, at its option, will either repair or

replace any assembly returned within its warranty period to the Customer

Service Department or an authorized service center. However, this will be done

only if the product is determined by Teledyne LeCroy’s examination to be

defective due to workmanship or materials, and the defect is not caused by

misuse, neglect, accident, abnormal conditions of operation, or damage resulting

from attempted repair or modifications by a non-authorized service facility.

The customer will be responsible for the transportation and insurance charges

for the return of products to the service facility. Teledyne LeCroy will return all

products under warranty with transportation charges prepaid.

This warranty replaces all other warranties, expressed or implied, including but

not limited to any implied warranty of merchantability, fitness or adequacy for

any particular purposes or use. Teledyne LeCroy shall not be liable for any

special, incidental, or consequential damages, whether in contract or otherwise.

928602-00 Rev A

July, 2017

Operator’s Manual

Safety Instructions

Follow generally accepted safety procedures in addition to the precautions

specified in this section. The overall safety of any system incorporating this

accessory is the responsibility of the assembler of the system.

Symbols

These terms and symbols may appear on the probe body or in this manual to

alert you to important safety considerations.

High Voltage WARNING, risk of electric shock or burn.

CAUTION of potential damage to equipment, or WARNING of

potential injury. Attend to the accompanying information to protect

against personal injury or damage. Do not proceed until conditions

are fully understood and met.

DOUBLE INSULATION

PROTECTIVE (EARTH) TERMINAL

Precautions

To avoid personal injury or damage to property, review and comply with the

following safety precautions. Use product only as specified.

Connect only to grounded instruments. Use only with compatible Teledyne

LeCroy oscilloscopes that have their BNC input connected to an earth

ground. Do not connect the probe reference lead to any point which is at a

potential other than earth ground.

Connect and disconnect properly. Connect probe to the oscilloscope before

connecting the probe to the test circuit. Disconnect the probe input and

reference lead from the test circuit before disconnecting the probe from the

oscilloscope. To avoid injury or death due to electric shock, do not connect or

disconnect probes or probe accessories while they are connected to a

voltage source.

PP016 Passive Probe

Do not overload;observe all terminal ratings. To avoid electric shock or fire,

do not apply any potential to the probe leads that exceeds the maximum

rating of the probe. Consult the respective oscilloscope product manual for

further ratings information.

Comply with voltage derating curve. When measuring higher frequency

signals, comply with the Voltage vs. Frequency Derating Curve.

Do not remove probe casing. Removing the probe’s case or touching exposed

connections may result in electric shock.

Use only within operational environment listed. Use indoors only. Do not use

in wet or explosive atmospheres. Keep product surfaces clean and dry.

Use only accessories compatible with the probe.

Handle with care. The probe tip is extremely sharp and may puncture skin or

cause other bodily injury if not handled properly.

Keep fingers behind the finger guard of probe body and accessories.

Do not operate with suspected failures. Before each use, inspect the probe

and accessories for any potential damage such as tears or other defects in

the probe body, cable jacket, accessories, etc. If any part is damaged, cease

operation immediately and sequester the probe from inadvertent use.

Operator’s Manual

Introduction

PP016 is a passive probe designed to be used with Teledyne LeCroy

WaveAce oscilloscopes.

Keep fingers behind the probe’s finger guard during use.

Rated for indoor use only. Do not operate where conductive pollutants

may be present.

Maximum input voltage derates when frequency response is

approximately 30 kHz or higher. See voltage derating curve on p.4.

Specifications

Electrical Characteristics

Attenuation 1:1 10:1

Bandwidth 10 MHz 300 MHz

Input Resistance 1 MΩ10 MΩ

Input Capacitance 46 pF 12 pF

Compensation Range NA 10–35 pF

Electrical Ratings*

Max. Input Voltage CAT II, 600 V (AC + DCpeak)

Pollution Degree 2

* See Certifications for an explanation of rating categories.

Operating Environment

Temperature, Operating 0oto 50oC

Temperature, Storage -20oto 60oC

Altitude, Operating Up to 3000 m (9842 ft)

Humidity, Operating 5% to 85% RH to 30° C

5% to 65% RH 30° C to 40° C

5% to 45% RH above 40° C

PP016 Passive Probe

General Characteristics

Cable Length 1.2 m

Weight (probe only) 54 g

Connector Type BNC

Voltage Derating Curve

(Max. VIN vs. Frequency)

Operator’s Manual

Connectivity Accessories

The following accessories are included standard with the PP016:

QTY

Standard Ground Lead 1

Sprung Hook 1

Color Coding Rings (set) 2

Adjustment Tool 1

Ground Attachment 1

Replacement Probe Tip 2

BNC Adaptor 1

IC Test Tip 2

The Standard Accessory Replacement Kit for the PP016 probe is P/N

PKIT3-5MM-101.

PP016 Passive Probe

Use and Maintenance

Cleaning

The outside of the probe should cleaned with a soft cloth dampened with

either deionized / distilled water or isopropyl alcohol. Allow the surface to

dry completely before returning the probe to service. Never immerse the

probe in any liquid.

Probe Compensation

Proper compensation of the probe is required to assure good amplitude

accuracy in the dynamic portions of the waveform being measured. LF

compensation matches the probe to differences in oscilloscope input

capacitance. The LF compensation should always be checked and adjusted

as needed when first connecting a passive probe to the oscilloscope input.

HF compensation matches time constants within the probe to compensate

for normal component tolerances. It is typically not necessary to adjust HF

compensation unless the probe is being used with an oscilloscope with large

differences in input characteristics than the oscilloscope model it was

designed for.

LF compensation is performed by connecting the input of the probe to a low

frequency square wave, such as the oscilloscope calibrator signal set to 1

kHz. The compensation is adjusted by rotating the adjustment accessible

through the small hole in the center of the housing near the BNC connector.

Use the tool supplied with the probe for this adjustment.

Over-compensated, correct, and under-compensated waveforms

Operator’s Manual

Certifications

Teledyne LeCroy certifies compliance to the following standards as of the

date of publication. See the EC Declaration of Conformity shipped with the

product for current certifications.

EC Declaration of Conformity - Safety

The probe meets intent of EC Directive 2014/35/EU for Product Safety.

Compliance was demonstrated to the following specifications as listed in the

Official Journal of the European Communities:

IEC/EN 61010-031:2015 Safety requirements for electrical equipment for

measurement, control and laboratory use – Part 031: Safety requirements for

handheld probe assemblies for electrical measurement and test.

•Measurement Category II (CAT II) refers to measurements performed

on circuits directly connected to utilization points (socket outlets and

similar) of the low-voltage mains installation.

•Pollution Degree 2, operating environment where normally only dry

non-conductive pollution occurs. Conductivity caused by temporary

condensation should be expected.

Environmental Compliance

END-OF-LIFE HANDLING

The probe is marked with this symbol to indicate that it complies

with the applicable European Union requirements to Directives

2012/19/EU and 2013/56/EU on Waste Electrical and Electronic

Equipment (WEEE) and Batteries.

The probe is subject to disposal and recycling regulations that vary

by country and region. Many countries prohibit the disposal of waste

electronic equipment in standard waste receptacles. For more information

about proper disposal and recycling of your Teledyne LeCroy product, please

visit teledynelecroy.com/recycle.

RESTRICTION OF HAZARDOUS SUBSTANCES (ROHS)

The probe and accessories conform to the 2011/65/EU RoHS2 Directive.

PP016 Passive Probe

Otros manuales para PP016

Tabla de contenidos

Otros manuales de Instrumento de medición de Teledyne Lecroy

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook CP030B Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Frontline BPA 500 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy PCI Express Gen 4x8 OCuLink Manual de usuario

Teledyne Lecroy

Teledyne Lecroy WaveRunner 8000-R Manual de usuario

Teledyne Lecroy

Teledyne Lecroy WavePulser 40iX Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Summit T416 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy ZS Series Manual de usuario

Teledyne Lecroy

Teledyne Lecroy AP031 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy HVFO108 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy DXC100A Manual de usuario

Teledyne Lecroy

Teledyne Lecroy MDA810 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Frontline Sodera LE Manual de usuario

Teledyne Lecroy

Teledyne Lecroy M42de Manual de usuario

Teledyne Lecroy

Teledyne Lecroy PP016 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy AP015 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy BPA Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook SierraNet M168 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook Frontline X500 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy 280 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy frontline SODERA Manual de usuario

Teledyne Lecroy

Teledyne Lecroy SierraNet M328 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy M41h Manual de usuario

Teledyne Lecroy

Teledyne Lecroy ZD200 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario