Techno CNC Systems Titan Series Manual de usuario
1Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
This document will provide a quick guide to the set up and operating
procedure of the Techno Titan CNC Router with a WinCNC Controller.
The Techno Titan CNC Router is powered by high precision stepper motors
and controlled by a PC with a WinCNC Control System.
Techno CNC Systems, LLC. ©2015 (06/17)
2Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
TABLE OF CONTENTS
Forklift Guide .........................................................................Page 3
Safety Instructions ...............................................................Page 4
Colleting Guidelines ...............................................................Page 5
IInitial Setup
1.1 Titan Series Series Installation .................................Page 6
1.2 Titan Series Series Installation .................................Page 10
II Controller Functionality
2.1 Control Panel Functions .....................................................Page 12
2.2 Enabling the Machine ...........................................Page 13
2.3 Software Overview .....................................................Page 15
2.4 Program Shortcuts .....................................................Page 26
III Operating Tutorials
3.1 - Machine Startup - Homing ...........................................Page 28
3.2 - Manaul Operation .....................................................Page 28
3.3 - Axis Window ...............................................................Page 29
3.4 - Park Position ...............................................................Page 29
3.5 - Functions ...............................................................Page 30
3.6 - Adjusting the XYZ Position/WCS/User Origin .......................Page 32
3.7 - Running a G-code File .....................................................Page 34
IV Advanced Tutorials
4.1 Tool Changes ...............................................................Page 35
4.2 Measuring Tool Lengths .....................................................Page 35
4.3 Learning Pocket Positions ...........................................Page 38
4.4 4th axis .........................................................................Page 40
V Controller Commands (G, M and L codes) ......................Page 41
VI Error Messages ..............................................................Page 69
VII Maintainence ........................................................................Page 75
VIII Warranty ........................................................................Page 89
3Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
4Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
1. Keepngers,hands,andallotherobjects
away from machine while power is on.
2. Disconnect power to all system components
when not in use, when changing accessories,
and before servicing.
3. Do not loosen, remove, or adjust machine
parts or cables while power is on.
4. Exercise care with machine controls and
around keyboard to avoid unintentional
starting.
5. Make sure voltage supplied is appropriate to
specicationsofcomponents.
6. Machines must be plugged into three-
pronged grounded outlets. Do not remove
the grounding plug or connect into an
ungrounded extension cord.
7. Keep cables and cords away from heat, oil,
and sharp edges. Do not overstretch or
run them under other objects or over work
surfaces.
8. Useproperxturesandclampstosecure
work. Never use hands to secure work.
9. Do not attempt to exceed limits of machine.
10. Do not attempt to use machine for purposes
other than what is intended.
11. Use machine only in clean, well-lit areas
freefromammableliquidsandexcessive
moisture.
12. Stay alert at all times when operating the
machine.
13. Always wear safety goggles.
14. Donotwearloose-ttingclothingwhen
operating machine. Long hair should be
protected.
15. Always maintain proper balance and footing
when working around the machine.
16. Maintainequipmentwithcare.Keepcutting
tools clean and sharp. Lubricate and change
accessories when necessary. Cables and
cords should be inspected regularly. Keep
controls clean and dry.
17. Before using, check for damaged parts. An
authorized service center should perform
all repairs. Only identical or authorized
replacement parts should be used.
18. Remove any adjusting keys and wrenches
before turning machine on.
19. Do not operate the machine unattended.
20. Follow all safety instructions and processing
instructions in the MSDS for the material
being processed.
21. Use proper precautions with dust collection
systemstopreventsparksandrehazards.
22.Makesuretohaveproperreextinguishing
equipmentonhandatalltimes.
WARNING: IMPROPER OR UNSAFE OPERATION OF THE MACHINE WILL
RESULT IN PERSONAL INJURY AND/OR DAMAGE TO THE EQUIPMENT.
READ THESE INSTRUCTIONS THOROUGHLY BEFORE OPERATING MACHINE.
DO NOT OPERATE MACHINE IF YOU ARE UNFAMILIAR WITH THESE SAFE
OPERATING INSTRUCTIONS. DO NOT OPERATE MACHINE WITHOUT
KNOWING WHERE THE EMERGENCY STOP SWITCH IS LOCATED.
PREVENT FIRE HAZARDS by using the proper feeds, speeds, and tooling while
operating your Techno machine. For example, setting feeds and speeds too low
and/or using dull tool bits creates friction at the material. The friction generates
heat which can result in a re that can be drawn through the vacuum table or
dust collector without warning. Fire hazard from friction heating caused by dull
tools is possible when cutting certain materials, especially composite material
such as wood composites, MDF and Particleboard. © 2012
Safety Instructions
5Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
WARNING!
THE SPINDLE WILL BE DAMAGED
IF UNBALANCED EQUIPMENT IS USED.
AIR SUPPLY MUST BE FILTERED AND DRY.
6Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
I. Initial Setup
Remove the controller and place it on the oor to the left of the machine.
When unpacking the controller, avoid twisting the cable carrier that guides the cables to the motors.
Carefully remove the Titan from its wood pallet. Be sure to remove the bolts from its four leveling feet
insertion holes, as well as anything stowed under the Titan during shipping.
Remove all bubble wrap, foam and strapping from the machine.
Attached the provided leveling feet to the six legs and adjust accordingly until the table is level.
Remove the four brackets used to stabilize
the gantry during shipping using metric allen
wrenchs.
1.1 Techno Titan Series Installation
7Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
L1 L2 L3
Fig. 1.2a
Enclosure
The Electronics are housed in the large NEMA enclosure
as shown in Fig. 1..2a. When unpacking the machine avoid
twisting the cable carrier that guides the cables to the
motors.
Have a suitably qualied
person connect the 220V
to the shown terminals.
Make sure that all local
electrical codes are obeyed.
For single phase machine,
connect power to L1 and L3
only.
Fig. 1.2c
Open the rear of the controller
using the provided key located
around the emergency stop
button or inside of the tool box.
You will now have access to the
electronics that drive the CNC.
They will be identical or like
depending on the model issued.
(shown in Fig. 1..2b).
The terminals for the
220 volt connection are located
at the bottom of the box
(shown in Fig. 1..2c)
Fig. 1.2b
A- Controller Board.
B- 24Volt PSU.
C- Stepper Driver.
D- 220Volt In.
A B
C
D
8Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
Install the 37 pin cable from the control box into the rear of the PC.
The cable from the WinCNC board must go to the BLUE
connector.
Unpack the PC, monitor, keyboard and mouse and began
mountingtheequipment.Attachthemonitortotheprovided
mount, place the PC in the side tray and connect both to a
110VAC power source.
Rout keyboard and mouse to PC and make sure the monitor
is also connected.
9Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
10 Call: 1-631-648-7481 or Visit: support.technocnc.com
Titan Series WinCNC Manual
WinCNC
1.2 Vacuum Pump Installation
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de control de Techno CNC Systems
