TE Connectivity 58075-1 Manual de usuario

Instruction Sheet

1 of 7

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-6789

28 SEP 2021 Rev F

PROPER USE GUIDELINES

Cumulative trauma disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional

use and low-volume applications. A wide selection of powered application equipment is available for extended-use production operations.

Figure 1: Pistol Grip Pneumatic Handle Assembly 58075-1

Air cylinder

Body

Key (visible on this side)

Trigger

Handle

Air tube

1. INTRODUCTION

These instructions deal with the safety, installation, operation and maintenance of the Pistol Grip Pneumatic

Handle Assembly 58075-1 (Figure 1).

Pistol Grip Pneumatic Handle Assembly 58075-1 accepts interchangeable terminating heads that terminate

wires in connectors. To ensure accurate termination of wires, setup adjustments, and head maintenance, refer

to the instructions packaged with the terminating head.

NOTE

Dimensions in this instruction sheet are in millimeters with [inches in brackets]. Figures are for reference only and are not

drawn to scale.

Reasons for reissue of this instruction sheet are provided in section 8, REVISION SUMMARY.

Pistol Grip Pneumatic

Handle Assembly 58075-1

408-6789

Rev F

2 of 7

2. DESCRIPTION

The pneumatic handle assembly features a molded nylon handle with a trigger and an air tube. The handle

holds an air cylinder with a key that retains the terminating head in the body and allows the head to be rotated

(Figure 1).

In this use, the handle assembly with the terminating head emits a maximum noise level of 78 dB. The vibration

level is less than 2.5 mm/s².

Figure 2 shows the dimensions of the handle assembly. The weight is 510 g [1 lb, 2 oz].

Figure 2: Dimensions

408-6789

Rev F

3 of 7

3. INSTALLING AND REMOVING THE HEAD

DANGER

To avoid personal injury, always disconnect the handle assembly from the air supply when installing or removing the head.

1. Disconnect or lock out the tool from its air supply.

2. Position the blade tip of a screwdriver between the shoulder of the key and the handle assembly body.

Pry and remove the key (Figure 3).

3. Insert the terminating head into the head entrance until the head bottoms (Figure 3).

Figure 3: Inserting the terminating head

Key

Terminating head (for reference)

Head entrance

4. Re-insert the key to retain the head.

5. To remove the head, remove the key and pull the head out of the handle assembly.

408-6789

Rev F

4 of 7

4. SETUP

Use a regulator-filter-lubricator unit with the lubricator adjusted to the minimum setting (Figure 4).

Figure 4: Regulator-filter-lubricator unit

Air supply

Filter and moisture separator

Regulator

Lubricator

To handle assembly

Use quick-disconnect fittings to connect the tool to the air supply. If not using quick-disconnect fittings, provide

a pneumatic lock-out on the air line that bleeds air after it is turned off.

The handle assembly is designed to operate with an air pressure range of 276 to 483 kPa [40 to 70 psi].

Service life can be greatly extended when only the necessary air pressure is applied. Excessive pressure

causes wear and strain on handle assembly components and the connectors.

CAUTION

Do not use this tool as a blunt object, a crushing device, or for any purpose other than crimping the proper specified product.

Inappropriate use of the tool can result in personal injury or damage to the tool.

5. OPERATION

The following procedure provides only general information concerning crimping. Refer to the instructions

packaged with the terminating heads for detailed information, including wire stripping dimensions and

instructions for positioning terminals in the terminating heads.

1. Insert the connector into the left side of the head.

2. Align the contact to be terminated with the wire inserter of the head. Make sure that the locating pawl

rests between the connector index ribs.

3. Insert an unstripped wire into the funnel area between the contact and the wire inserter until it bottoms

on the tool base.

4. Press the trigger of the handle assembly and hold it until the wire inserter bottoms.

5. Release the trigger. The wire inserter retracts. The feed slide automatically advances the connector to

the next contact position.

6. Repeat steps 2 through 5 until all contacts have been terminated.

7. Inspect each termination.

408-6789

Rev F

5 of 7

6. MAINTENANCE AND INSPECTION

DANGER

To avoid personal injury, always disconnect the handle assembly from the air supply when performing maintenance or

inspection procedures.

Each handle assembly is inspected before shipment. Inspect the handle assembly immediately upon arrival at

the facility of use to ensure that it has not been damaged during shipping.

6.1. Daily maintenance

Each operator of the power unit must be aware of, and responsible for, the following daily maintenance

requirements:

1. Remove dust, dirt and other contaminants with a clean brush or soft lint-free cloth. Do not use objects

that could damage the handle assembly.

2. Ensure that all components are in place and properly secured.

3. With the terminating head in place, connect the air supply.

4. Squeeze and release the trigger to ensure that the mechanisms and plunger move smoothly.

6.2. Periodic inspection

Regular inspections must be performed at least once per month. Base your inspection frequency on

amount of use, the presence of abnormal amounts of dust and dirt, operator training and skill, and

established company standards.

Remove any accumulated film with a suitable cleaning agent that does not affect plastic material.

Check the handle assembly for chipped, cracked, worn, or broken areas. If damage is evident, repair is

necessary. See section 7, REPLACEMENT AND REPAIR.

408-6789

Rev F

6 of 7

7. REPLACEMENT AND REPAIR

Customer-replaceable parts are shown in Figure 5.

Figure 5: Customer-replaceable parts

Item

Part number

Description

Quantity per

assembly

27174-1

Valve, poppet

1-21003-3

Screw, flat head socket cap

28472-1

Push button trigger, valve actuator

312140-1

Key

312141-1

Nut, cam adjustment

312157-1

Air cylinder

310421-1

Plug, cap

310424-1

Bracket, air cylinder

21086-6

O-ring

312156-1

Handle

312622-2

Subassembly, air tube

Stock and control a complete inventory to prevent lost time when replacement of parts is necessary. Parts

other than those listed should be replaced by TE to ensure quality and reliability of the handle assembly. Order

replacement parts through your TE representative. You can also order parts by any of the following methods:

Go to TE.com and click the Shop TE link at the top of the page.

Call 800-522-6752.

Write to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

For customer repair services, call 800-522-6752.

408-6789

Rev F

7 of 7

8. REVISION SUMMARY

Revisions to this instruction sheet include:

Removed CE label from Figure 5.

Reformatted to match current standard for instruction sheets.

Tabla de contenidos

Otros manuales de Herramientas de crimpado de TE Connectivity

TE Connectivity

TE Connectivity ERGOCRIMP 539 748-2 Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 0-539956-2 Manual de usuario

TE Connectivity

TE Connectivity IDC Hand tool RAST 2.5 Manual de usuario

TE Connectivity

TE Connectivity TERMI-FOIL 68026 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 69339 Manual de usuario

TE Connectivity

TE Connectivity 2393700-1 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III 2161732-1 Manual de usuario

TE Connectivity

TE Connectivity 528050-3 Manual de usuario

TE Connectivity

TE Connectivity HDP-400 Guía de referencia

TE Connectivity

TE Connectivity 2844461-2 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA PN 2063626-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 90080-2 Manual de usuario

TE Connectivity

TE Connectivity 2390882-1 Manual de usuario

TE Connectivity

TE Connectivity 58079-3 Manual de usuario

TE Connectivity

TE Connectivity CERTI-CRIMP Manual de usuario

TE Connectivity

TE Connectivity 2395308-1 Manual de usuario

TE Connectivity

TE Connectivity 2063379-1 Manual de usuario

TE Connectivity

TE Connectivity FDH 3000 864 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 68321-1 Manual de usuario

TE Connectivity

TE Connectivity CERTI-CRIMP 90066-7 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

molex

molex 63811-5100 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

molex

molex 63825-3000 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario