TE Connectivity 46073 Manual de usuario

Instruction Sheet

1 of 7

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-1536

22 MAY 17 Rev J1

Figure 1

INTRODUCTION

Hand Crimping Tools 46073 and 46074 are designed to crimp CERTI-SEAL* moisture-proof splices onto

stranded copper wire sizes 24 thru 16 AWG.

NOTE

Read these instructions thoroughly before using the hand tool.

NOTE

Dimensions in this instruction sheet are in millimeters [with inches in brackets]. Figures and illustrations are for reference only

and are not drawn to scale.

Reasons for reissue of this instruction sheet are provided in Section 6, REVISION SUMMARY.

DESCRIPTION (FIGURE 1)

The hand tools are designed with two indenter (crimper) dies, two anvil (stationary) dies, a locator, and a

CERTI-CRIMP tool ratchet. When closed, the dies form one crimping chamber. The ratchet assures full

crimping of the splice. Once engaged, the ratchet will not release until the tool handles have been FULLY

closed.

CAUTION

The dies bottom before the ratchet releases. This design feature ensures maximum electrical and tensile performance of the

crimp. DO NOT re-adjust the ratchet.

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low

volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Hand Crimping Tools;

PN 46073 and PN 46074

408-1536

Rev J1

2 of 7

CRIMPING PROCEDURE

NOTE

Each hand tool is coated with a preservative to prevent rust or corrosion. Wipe this preservative from

the tool, particularly from the dies, before using the tool.

1. Select the correct splice for the wire size and wire insulation diameter being used. Observe color

coding of splice, rings, adaptors, and tools (see Figure 2).

Wire

Splice

Wire Strip

Length

mm [inch]

Splice Body

and Tool

Color Code

Tool

Adapter

Ring Color

Size Range

(AWG)

Max Insul

Diameter

mm [inch]

24-20

1.65 [.065]

324987

Yes

Green

7.37 [.290]

Tin

(White)

46073

1.85 [.073]

1-324987-0

Orange

1.85 [.073]

1-324987-1

---

Yes

---

Orange

2.54 [.100]

---

Tin

---

6.35 [.250]

2.54 [.100]

324544

---

Tin

20-18

2.57 [.101]

324988

Yes

Green

7.87 [.310]

Red

46074

3.38 [.133]

324548

---

Tin

7.11 [.280]

Figure 2

2. Strip the wire to dimensions listed in Figure 2. DO NOT nick or cut the wire strands.

3. Open the dies by squeezing the tool handles together until the ratchet releases.

4. Select the proper color-coded end of splice (when applicable) for the wire insulation diameter being

used (see Figure 2).

5. Insert stripped wire into splice until it bottoms against wire stop. End of conductor should be visible

through transparent window indent of splice.

6. Align splice window indents with tool locator, and push splice into locator until splice bottoms (see

Figure 3).

7. Hold wire in place and squeeze tool handles together until the CERTI-CRIMP ratchet releases. Allow

tool handles to open FULLY. Crimped splice may be removed.

8. To crimp other half of splice, position uncrimped half in tool and follow same procedure used to crimp

first half of splice. If splice cannot be turned, turn tool around.

9. Refer to Figure 4 for splice crimp inspection.

408-1536

Rev J1

3 of 7

Figure 3

Figure 4

408-1536

Rev J1

4 of 7

MAINTENANCE AND INSPECTION

TE Connectivity recommends that a maintenance and inspection program be performed periodically to ensure

dependable and uniform terminations.

Frequency of inspection depends on:

1. The care, amount of use, and handling of the hand tool.

2. The presence of abnormal amounts of dust and dirt.

3. The degree of operator skill.

4. Your own established standards.

NOTE

The hand tool is inspected before being shipped from the plant; however, it is recommended that the tool be inspected

immediately upon arrival to ensure that the tool has not been damaged during shipment.

NOTE

Due to the precision design, it is important that no parts of these tools be interchanged except the replacement parts listed in

Figure 7.

4.1. Daily Maintenance

1. Remove dust, moisture, and other contaminants with a clean, soft brush, or a clean, soft, lint-free

cloth. DO NOT use any objects that could damage the tool.

2. Make sure the retaining pins are in place and that they are secured with retaining rings.

3. All pins, pivot points, and bearing surfaces should be protected with a thin coat of any good SAE 20

motor oil. DO NOT oil excessively.

4. When the tool is not in use, keep the handles closed to prevent objects from becoming lodged in the

dies. Store the tool in a clean, dry area.

4.2. Lubrication

Lubricate all pins, pivot points, and bearing surfaces with SAE 20 motor oil as follows:

Tool used in daily production - lubricate daily

Tool used daily (occasional) - lubricate weekly

Tool used weekly - lubricate monthly

Wipe excess oil from tool, particularly from crimping area. Oil transferred from the crimping area onto certain

terminations may affect the electrical characteristics of an application.

4.3. Periodic Inspection

1. Hand tool should be immersed (handles partially closed) in a reliable commercial degreasing

compound to remove accumulated dirt, grease, and foreign matter.

2. Close tool handles until ratchet releases and then allow them to open freely.

If they do not open quickly and fully, the spring is defective and must be replaced; see Section 5,

REPLACEMENT AND REPAIR.

3. Inspect head assembly for worn, cracked, or broken dies.

If damage is evident, see Section 5, REPLACEMENT AND REPAIR for information on obtaining

customer repair service.

SAE is a trademark

408-1536

Rev J1

5 of 7

Gaging the Crimping Chamber

This inspection requires the use of a plug gage conforming to the dimensions provided in Figure 5.

NOTE

TE Connectivity does not manufacture or market these gages.

For Tools 46073 and 46074

Tool

Gage Element Diameter mm [inch]

NO-GO

46073

2.464-2.471 [.0970-.0973]

2.614-2.616 [.1029-.1030]

46074

2.997-3.005 [.1180-.1183]

3.147-3.150 [.1239-.1240]

For Tool 46073 For Tool 46074

Figure 5

To gage the crimping chamber, proceed as follows:

1. Remove traces of oil or dirt from the crimping chamber and plug gage.

2. Close the tool handles until it is evident that the dies have bottomed; then hold in this position. DO

NOT force the dies beyond initial contact.

3. Align the GO element with the wire barrel crimping section. Push element straight into the crimping

chamber without using force. The GO element must pass completely through the crimping chamber

(see Figure 6).

408-1536

Rev J1

6 of 7

Figure 6

4. Align the NO-GO element and try to insert it straight into the same crimping chamber. The NO-GO

element may start entry, but must not pass completely through the crimping chamber (see Figure 6).

5. With dies bottomed, check insulation (ring) crimping section using the appropriate plug gage in same

manner as Steps 3 and 4.

If the crimping chamber conforms to the gage inspection, the tool is considered dimensionally correct, and

should be lubricated with a THIN coat of any good SAE 20 motor oil.

If not, refer to Section 5, REPLACEMENT AND REPAIR, for information on obtaining further evaluation and

repair.

For additional information regarding the use of a plug gage, refer to Instruction Sheet 408-7424.

CERTI-CRIMP Ratchet Inspection

The CERTI-CRIMP tool ratchet on these hand tools should be checked to ensure that the ratchet does not

release prematurely; allowing the dies to open before they have fully bottomed. Obtain a 0.025 mm [.001 inch]

shim that is suitable for checking the clearance between the bottoming surfaces of the dies. Proceed as

follows:

1. Refer to Figure 2, and select a splice and maximum size wire for the tool.

2. Position the splice and wire between the dies, as described in Section 3, CRIMPING PROCEDURE.

3. Hold the wire in place and squeeze the handles until the ratchet releases. Hold the handles in this

position, maintaining just enough tension to keep the dies closed.

4. Check the clearance between the bottoming surfaces of the dies. If the clearance is 0.025 mm [.001

inch] or less, the ratchet is satisfactory. If clearance exceeds 0.025 mm [.001 in.], the ratchet is out of

adjustment and must be repaired. See Section 5, REPLACEMENT AND REPAIR.

408-1536

Rev J1

7 of 7

REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Figure 7. A complete inventory should be stocked and controlled to

prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced to

ensure quality and reliability. Order replacement parts through your TE Connectivity representative, or call 1-

800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

For customer repair service, please contact a TE Connectivity representative at 1-800-526-5136.

Replacement Parts

Item

Part Number

Description

Qty Per Tool

21045-3

Ring, Retaining

304197-5

Pin, Retaining

1-23619-6

Pin, Retaining

6-59591-7

Collar

39364

Spring

2-23620-9

Pin, Retaining

21045-6

Ring, Retaining

Figure 7

REVISION SUMMARY

Paragraph 1: Corrected part number 46-74 with 46074

Page 4: Removed footnote and replaced with typical trademark notation

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de TE Connectivity

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063574-1 Manual de usuario

TE Connectivity

TE Connectivity 2063536-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA PN 2063534-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity SDE-SA 2389861-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 2407132-1 Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 539 725-2 Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 539 692-2 Manual de usuario

TE Connectivity

TE Connectivity 2063624-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 2378724-1 Manual de usuario

TE Connectivity

TE Connectivity TETRA-CRIMP 59824-1 Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 2-1579016-2 Manual de usuario

TE Connectivity

TE Connectivity 2391481-2 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity CERTI-CRIMP 90066-7 Manual de usuario

TE Connectivity

TE Connectivity 2386893-1 Manual de usuario

TE Connectivity

TE Connectivity 234170-1 Manual de usuario

TE Connectivity

TE Connectivity COPALUM 408-2281 Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

TE Connectivity

TE Connectivity 2393700-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

molex

molex 63811-5100 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

molex

molex 63825-3000 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario