TAKE-A-LABEL TAL-3100T Manual de usuario
Operations Manual
TAL-3100T
Tamp Applicator
770-554-1187
Helpful setup videos can be found on included USB or at www.take-a-label.com
1. Unpack TAL-3100T Tamp Label applicator from shipping container and remove from base.
2. Place the TAL-3100T on a rm level surface.
3. Plug the TAL-3100T into an 110VAC 15 AMP Grounded outlet.
4. Connect the labeler to a sucient air supply. Minimum 80 PSI clean dry air.
NOTES: • e TAL-3100T typically operates between 30-50 PSI depending on the label.
• When air is connected the vacuum generator will continually release air to create the vacuum eect.
LABEL THREADING
1. Remove outer unwind disc (49) install new roll of labels and replace disc.
2. Pull label web under the rst roller, threw the photo eye (21). Continue pulling the label web over the top
of the next roller. As the webbing is wrapped around the peel edge, take care to go between the bottom of
the peel edge and the top of the air assist tube. (Do not cover the air assist tube with the webbing).
3. Pull web back and wrap under the drive roller (35), and up between the drive roller (35) and pinch
roller (24), then back down to the waist wind sha (47). Note: e pinch roller (26) is spring loaded.
Slight pressure will be needed to separate the pinch roller from the drive roller for threading.
4. Install waist wind clip (48) on waist wind sha (47) placing the webbing between the sha and the clip.
TAL-3100T
MACHINE STARTUP
1. It is recommended that you teach the photo eye (21) with every new roll of labels used.
2. Remove one label from the webbing and place the webbing only in the photo eye.
3. Press and hold the “Normal” button on photo eye for 3 seconds. When the lights nish ashing the photo
eye is taught.
TAL-3100T
TEACHING THE PHOTO EYE
TAL-3100T
TAMP HEAD PLACEMENT
1. e tamp head placement is crucial for consistent label application.
2. e vertical gap between the top of peel plate and bottom of the tamp pad
should range from 0”-1/32”. If not loosen the nut at the base of the tamp
cylinder rod (Shown with red arrow A), and unthread to lower the tamp
pad or screw in the rod to raise the tamp pad height.
3. e horizontal gap between the top of peel plate and the edge of the tamp
pad should range from 0”-1/32”. If not loosen the horizontal mounting
bolts and align to the acceptable range.
ASSIST TUBE PLACEMENT
1. e air assist tube is used to assist the label out
onto the vacuum pad. As a rule of thumb the
blast patter from this tube should be directed
at a 30° angle onto the vacuum pad. is angle
may vary due to several factors, as a result
dierent blast angles may have to be
experimented with.
LABEL SETUP
TAL-3100T
e label advance potentiometer resides on top of the TAL-3100T electrical housing. e purpose is to
adjust the stopping position of the label with respect to the peel plate. With the label advance pot turned
all the way counterclockwise the photo eye will stop the applicator instantly when it senses a gap. By
rotating the potentiometer toward the + the applicator will dispense more of the label, and by rotating
the potentiometer toward the – the applicator will dispense less of the label.
1. To setup the label position, rotate the label advance pot to the – as far as it will rotate.
2. e goal is to have the applicator stop with a label gap right at the peel edge.
3. Activate the applicator and watch the dispensing label. If the label does not advance far enough
turn the label advance pot to the +, and repeat until one label is completely dispensed and the
next label is stopped at the peel edge.
TAL-3100T
TAMP HEAD SPEED
1. To adjust the speed of the tamp head going down to apply the label, turn the ow control (44A) clockwise
to slow it down and counterclockwise to speed it up.
2. To adjust the speed of the tamp head returning to the ready position, turn the ow control (44B)
counterclockwise to make the tamp head travel faster and clockwise to slow down.
TAL-3100T
TAMP HEAD DWELL TIME
LABEL ADVANCE DELAY
ADJUSTING LABEL ADVANCE DELAY:
Knob A: increases or decreases the time before the label is advanced on to the tamp pad. is variance will
occur aer activating the footswitch and beginning the cycle.
ADJUSTING DWELL TIME:
Knob B: increases or decreases the amount of time the tamp pad remains at the bottom of the cylinders stroke.
Before returning to the raised position.
Item# Description #
11002 Peel Plate 1
11008 Unwind Sha 2
21002 Housing 3
21003 Housing Cover 4
21004 Outboard Support Plate 5
21010 Pinch Roller Sha 6
21011 Idler Roller Rod 7
21031 Drive V Belt 8
21026 Motor Spacers 9
21027 Le Torsion Spring 10
21028 Right Torsion Spring 11
25112 Unwind Washer 12
25113 Unwind Spring 13
25124 #8 Self Taping Screw 14
26001 Unwind Collar 15
26002 Unwind Hub Screw 16
30005 Pneumatic Cylinder 17
31718 Air Assist Tube 18
30024 Anti-Rotation Rod 19
30074 Sha Collar ½” 20
30106 Tri-Tronics Photo Eye 21
30110 Foot Switch 22
30124 Filter/Regulator 23
30151 3/8” Sha Stop Collar 24
31002 Pinch Roller 25
31003 Outboard Support Sha 26
31717 Air Assist Bracket 27
31009 Pinch Roller Side Plate 28
31015 Plastic Bearing 29
31020 Cylinder Cross Mount Plate 30
31021 Cylinder Mount Plate 31
31053 80/20 Nut 32
31057 TAL-3100T Control Board 33
31060 Rewind Bracket 34
TAL-3100T
PARTS LIST
Distributed by: Pro Pack Solutions, Inc. ph 770-554-1187
TAL-3100T
PARTS LIST
Item# Description #
31282 V Belt Tensioner 35
31355 Drive Sha 36
31373 V Belt Pulley 37
31380 V Belt Tensioner Roller 38
31701 Main Frame 39
31702 Tamp Head Plate 40
31703 Product Guide Bars 41
31721 Rubber Feet 42
31722 Valve Assembly 43
31723 Flow Control Valve 44
31725 Vacuum Generator 45
40007 On/O Switch 46
45129 Waste Wind Sha 47
45131 Waste Wind Clip 48
45136 Unwind Disc 49
25211 IEC Connecter 50
45155 Fuse Holder 51
45157 Fuse 52
25212 Power Cord 53
72618 Felt Pad 54
76800 Heavy Duty Motor 55
81830 ½” Sha Caps 56
81912 Small Cord Grip 58
31417 Label Advance 10 Turn Pot
with wires 59
31416 Label Advance Knob 60
30084 Custom Tamp Pad 61
31014 Connecting Bracket 62
31020 Cylinder Cross Mount Plate 63
31021 Cylinder Mount Plate 64
Distributed by: Pro Pack Solutions, Inc. ph 770-554-1187
WIRING DIAGRAM
TAL-3100T
Otros manuales para TAL-3100T
1
Tabla de contenidos
Otros manuales de Accesorios de impresora de TAKE-A-LABEL
