Synology SA3600 Manual

Synology NAS SA3600

Hardware Installation Guide

Table of Contents

Chapter 1: Before You Start

Package Contents 3

Synology SA3600 at a Glance 4

Hardware Specication 5

Optional Accessories 6

Safety Instructions 8

Chapter 2: Hardware Setup

Tools and Parts for Component Installation 9

Install Drives 9

Install Memory Modules 11

Install PCle Add-in Cards 13

Install and Remove Rail Kits 15

Expansion Unit Deployment and Topology 18

Start up Your Synology NAS 19

LED Indicator Table 20

Chapter 3: System Maintenance

Replace System Fan 21

Replace Power Supply Unit (PSU) 23

Initial Troubleshooting Guide 23

Chapter 4: Install DSM on Synology NAS

Install DSM with Web Assistant 24

Learn More 24

Synology_HIG_SA3600_20190808

Synology NAS SA3600 is an enterprise server consisting of both system hardware and the software operating

system, DiskStation Manager (DSM). This manual will guide you through all conguration aspects of your

SA3600, including the hardware components, setup procedures, system maintenance, and initial troubleshooting

instructions.

Note: All images below are for illustrative purposes only, and may differ from the actual product.

Package Contents

Main unit x 1 AC power cord x 2

Screws for 2.5” drives x 52

Screws for 3.5” drives x 52

Before You Start 1

Chapter

4Chapter 1: Before You Start

Synology SA3600 at a Glance

No. Article Name Location Description

1 Power Button and Indicator

Front

1. Press to power on your Synology NAS.

2. To power off the Synology NAS, press and hold until you hear a beep

sound and the Power LED starts blinking.

2 Status Indicator Displays the status of the system. For more information, see "LED Indicator

Table."

3 Alert Indicator Displays warnings regarding fan or temperature. For more information, see

"LED Indicator Table."

4 Beep Off Button Press to deactivate the beeping sound that is emitted when a malfunction

occurs.

5 Drive Status Indicator Displays the status of drives. For more information, see "LED Indicator Table."

6 Drive Tray Install drives (hard disk drives or solid state drives) here.

7 Rail Kit Release Tab Push in and hold to release the Synology NAS from the rail kit lock.1

8 Power Port

Back

Connect power cords here.

9 PSU Indicator and Beep Off

Button

1. Displays the status of the power supply unit (PSU). For more information,

see "LED Indicator Table."

2. Press to deactivate the beeping sound that is emitted when a malfunction

occurs.

10 PSU Fan Disposes of excess heat and cools the PSU.

11 Console Port This port is used for manufacturing use only.

12 PCI Express Expansion Slot Supports additional PCIe network interface cards.

13 SAS OUT Port Connect to Synology Expansion Unit2here.

14 1GbE LAN Port Connect RJ-45 network cables here.

15 10GBase-T LAN Port Connect RJ-45 network cables here.

16 USB 3.0 Port Connect external drives, USB printers, or other USB devices to the Synology

NAS here.

17 Reset Button

1. Press and hold until you hear a beep sound to restore the default IP

address, DNS server, and password for the admin account.

2. Press and hold until you hear a beep sound, then press and hold again until

you hear three beep sounds to return the Synology NAS to “Not Installed”

status so that DiskStation Manager (DSM) can be reinstalled.

1For more information about the rail kit installation, please refer to the Quick Installation Guide that comes with the rail kit.

2For more information about Synology Expansion Unit supported by your Synology NAS, please visit www.synology.com.

5Chapter 1: Before You Start

Hardware Specication

Item SA3600

Compatible Drive Type 3.5”/2.5” SAS/SATA x 12

Maximum Raw Capacity • 192 TB (12 x 16TB HDD)

• 1536 TB with 7 x RX1217sas (expansion unit)

External Device Port • USB 3.0 x 2

• SAS OUT x 1

LAN Port • 1GbE (RJ-45) x 4

• 10GBase-T (RJ-45) x 2

PCIe Slot Gen3 x8 slots (x8 link) x 2

Size (H x W x D) (mm) • 88 x 482 x 724 (with server ears)

• 88 x 430.5 x 692

Weight (kg) 14.5

Supported Client • Windows 7 and 10

• Mac OS X 10.11 onward

File System • Internal: Btrfs, ext4

• External: Btrfs, ext4, ext3, FAT, NTFS, HFS+, exFAT1

Supported RAID Type • Basic • JBOD • RAID 0 • RAID 1

• RAID 5 • RAID 6 • RAID 10 • Synology RAID F1

Agency Certication • FCC Class A • CE Class A • BSMI Class A

• EAC • VCCI • CCC • RCM • RoHS Compliant

HDD Hibernation Yes

Scheduled Power On/Off Yes

Wake on LAN Yes

Language Localization

Environment Requirement

• Line voltage: 100V to 240V AC

• Frequency: 50/60Hz

• Operating Temperature: 32 to 95˚F (0 to 35˚C)

• Storage Temperature: -5 to 140˚F (-20 to 60˚C)

• Relative Humidity: 5% to 95% RH

Note: Model specications are subject to change without notice. Please refer to www.synology.com for the latest information.

1Support for exFAT can be enabled by purchasing and downloading exFAT Access in Package Center.

6Chapter 1: Before You Start

Optional Accessories

With Synology accessories, you can customize your Synology NAS to t different business environments without

worrying about compatibility and stability. Visit www.synology.com/compatibility for more information.

• Memory Module

Model Name Picture Description

D4RD-2666-16G 16GB DDR4-2666 ECC registered

DIMM

D4RD-2666-32G 32GB DDR4-2666 ECC registered

DIMM

Note: It is required to use D4RD-2666-16G with identical memory modules of the same capacity and frequency.

• PCIe Add-in Card

Model Name Picture Description

E10G18-T2 Dual-port, 10GbE RJ-45 network

interface card

E10G18-T1 Single-port, 10GbE RJ-45 network

interface card

E10G17-F2 Dual-port, 10GbE SFP+ network

interface card

• Expansion Unit

Model Name Picture Description

RX1217sas

12-bay rackmount type expansion

unit, compatible with 3.5”/2.5” SAS/

SATA drives

RX2417sas

24-bay rackmount type expansion

unit, compatible with 2.5” SAS/

SATA drives

Note: Your Synology NAS supports up to seven expansion units.

7Chapter 1: Before You Start

• Rail Kit

Model Name Picture Description

RKS1317 Sliding rail solutions

• Spare Part

Model Name Picture Description

Disk Tray (Type R7) 3.5"/2.5" drive tray

FAN 80*80*32_6 System fan module

PSU 500W-RP

Module_2 Redundant PSU module

PSU 500W-RP

SET_2

Redundant PSU set (cage x 1,

PSU module x 2)

8Chapter 1: Before You Start

Safety Instructions

Keep away from direct sunlight and away from chemicals. Make sure the environment does not

experience abrupt changes in temperature or humidity.

Place the product right side up at all times.

Do not place near any liquids.

Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or

aerosol cleaners.

To prevent the unit from falling over, do not place on carts or any unstable surfaces.

The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is

correct and stable.

To remove all electrical current from the device, ensure that all power cords are disconnected from

the power source.

Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.

Tools and Parts for Component Installation

Please prepare below tools and parts before setting up your Synology NAS:

• A screwdriver

• At least one 3.5” or 2.5” SAS/SATA drive (please visit www.synology.com/compatibility for compatible drive

models)

Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please

back up any important data before installation.

• Rail mounting kit (please see the Optional Accessories section to nd out the suitable rail kit for cabinet

installation)

Warning: We suggest mounting your Synology NAS on a cabinet before installing any drives since the heavy weight

will increase the installation difculty.

Install Drives

Please follow below steps for drive installation:

1 Open the drive tray.

a Find the small button located on the left side of the drive tray handle. Press the button down, and the drive

tray handle will pop out.

b Pull the drive tray handle out as illustrated above.

2 Install drives:

• For 3.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four

spots indicated below to secure the drive.

• For 2.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four

spots indicated below to secure the drive.

Hardware Setup 2

Chapter

10 Chapter 2: Hardware Setup

3 Insert the loaded drive tray into the empty drive bay.

Note: Make sure the tray is pushed in all the way. Otherwise, the drive might not be able to function properly.

4 Push the handle inward to secure the drive tray.

5 Push the switch on the drive tray handle to the left to lock the drive tray.

6 Repeat the steps above to assemble the other drives you have prepared.

7 Drives are numbered as shown below.

Note: We suggest installing drives of the same size to optimize drive capacity usage when creating RAID volumes.

Tabla de contenidos

Otros manuales de Almacenamiento de Synology

Synology

Synology DS-106j Manual de usuario

Synology

Synology SA3610 Manual de usuario

Synology

Synology RS1221+ Manual

Synology

Synology DS220j Manual

Synology

Synology diskstation DS416J Manual de usuario

Synology

Synology DX517 Manual

Synology

Synology TC500 Manual de usuario

Synology

Synology DiskStation DS214play Manual de usuario

Synology

Synology RS3413xs+ Manual de usuario

Synology

Synology DiskStation DS218play Manual

Synology

Synology DS109j Manual de usuario

Synology

Synology DiskStation DS409slim Manual de usuario

Synology

Synology DiskStation DS110+ Manual de usuario

Synology

Synology DiskStation DS1019+ Manual

Synology

Synology DS1621+ Manual

Synology

Synology DiskStation DS216j Manual de usuario

Synology

Synology DS411j Manual de usuario

Synology

Synology DiskStation DS715 Manual de usuario

Synology

Synology DiskStation DS214se Manual de usuario

Synology

Synology DiskStation DS2419+ Manual

Synology

Synology DS1823XS+ Manual de usuario

Synology

Synology DiskStation DS411slim Manual de usuario

Synology

Synology RackStation RC18015xs+ Manual de usuario

Synology

Synology FlashStation FS1018 Manual

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario