Synology DS2422+ Manual de usuario
Synology NAS DS2422+
Hardware Installation Guide
Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology DS2422+ at a Glance 4
System Modes and LED Indicators 5
Other LED Indicators 7
Hardware Specication 8
Spare Parts 9
Safety Instructions 10
Chapter 2: Hardware Setup
Tools and Parts for Component Installation 11
Install Drives 11
Start Up Your Synology NAS 14
Add a Memory Module to Synology NAS 15
Install PCle Add-in Cards 18
Chapter 3: System Maintenance
Replace System Fan 21
Chapter 4: Install DSM on Synology NAS
Install DSM with Web Assistant 23
Learn More 23
2
Synology_HIG_DS2422+_20210331
Thank you for purchasing this Synology product! Before setting up your new Synology NAS, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety instructions
carefully to avoid harming yourself or damaging your Synology NAS.
Note: All images below are for illustrative purposes only, and may dier from the actual product.
Package Contents
Main unit x 1 AC power cord x 1
RJ-45 LAN cable x 2
Hard drive tray key x 2
Screws for 2.5" drives x 52
Before You Start 1
Chapter
3
4Chapter 1: Before You Start
Synology DS2422+ at a Glance
No. Article Name Location Description
1 STATUS Indicator
Front
Displays the status of the system. For more information, see
"System Modes and LED Indicators".
2 ALERT Indicator Displays warnings regarding fan or temperature. For more
information, see "Other LED Indicators".
3 POWER Button
1. Press to power on your Synology NAS.
2. To power o your Synology NAS, press and hold until you
hear a beep sound and the Power LED starts blinking.
4 LAN Indicator Displays the status of the network connection. For more
information, see "Other LED Indicators".
5 DRIVE Status Indicator Displays the status of each drive. For more information, see
"Other LED Indicators".
6 Drive Tray Install drives (hard disk drives or solid state drives) here.
7 Drive Tray Lock Lock or unlock drive trays.
8 Power Port
Rear
Connect power cord here.
9 Fan Disposes of excess heat and cools the system. If the fan
malfunctions, the Synology NAS will emit a beeping sound.
10 PCI Express
Expansion Slot Supports one PCIe x8 slots (x8 link) add-on card.
11 RESET Button
1. Press and hold until you hear a beep sound to restore
the IP address, DNS server, and password for the admin
account to default.
2. Press and hold until you hear a beep, then press and hold
again until you hear three beeps to return the Synology
NAS to "Not Installed" status so that DiskStation Manager
(DSM) can be reinstalled.
12 USB 3.2 Gen 1 Port Connect external drives or other USB devices to the Synology
NAS here.
13 Console Port This port is used for manufacturing use only.
14 Expansion Port Connect Synology Expansion Unit1to the Synology NAS here.
15 LAN Port Connect network cables here.
1For more information about Synology Expansion Unit supported by your Synology NAS, please visit www.synology.com.
6
7
1
2 3
4
5
8
13
10
12
9
14
11
5
7
15
5Chapter 1: Before You Start
System Modes and LED Indicators
System Modes and Denitions
There are 7 system modes in Synology NAS. The System modes and their denitions are as below:
System mode Denition
Powering on Synology NAS is powering on and performing hardware initialization, such as
hardware reset or BIOS initialization.
Shutting down Synology NAS is shutting down as a result of pressing the power button or operation
in DSM.
DSM not ready
DSM is not ready for use. This could either be:
• Synology NAS is powered on, but DSM is not properly installed.
• Synology NAS is currently powering on and initializing services necessary for
DSM to fully function.
• The attached UPS device has insucient power; DSM stops all services to
prevent data loss (enters safe mode).
DSM is ready for use DSM is fully functioning and users can sign in.
Hibernation Synology NAS has been idle for a while and is now in Hibernation mode.
Application
Certain packages/services (e.g., USB Copy and Find me service) while in operation
will control the actions of the LED. After the operation is complete, the LED indicator
will return to its normal state.
Powered o Synology NAS is powered o.
Identify System Modes
You can identify the system mode through the POWER and STATUS LED indicators. Please refer to below table
for more details.
System mode
LED Indicator
POWER STATUS
Blue Green Orange
Powering on Blinking O O
Shutting down Blinking Static O
DSM not ready Static Blinking O
DSM is ready for use Static Static O
Hibernation Static O O
Application Static Switching
Powered o O O O
6Chapter 1: Before You Start
Transitions between System Modes
To better understand the transition between system modes, please refer to below examples:
• Powered on with no DSM installed:
Powered o > Powering on > DSM not ready
• Powered on with DSM installed:
Powered o > Powering on > DSM not ready > DSM is ready for use
• Enter hibernation then wake up from hibernation:
DSM is ready for use > Hibernation > DSM is ready for use
• Shutdown Synology NAS:
DSM is ready for use > Shutting down > Powered o
• Power failure with UPS attached:
DSM is ready for use > DSM not ready (due to power failure, DSM enters safe mode) > Shutting down >
Powered o > Powering on (power has recovered, DSM will reboot)> DSM not ready > DSM is ready for use
7Chapter 1: Before You Start
Other LED Indicators
LED Indicator Color Status Description
DRIVE status Indicator
(on tray)
Green
Static Drive ready and idle
Blinking Accessing drive
Orange Static Drive error/Port disabled1
O No internal Drive
ALERT
Red Blinking System error2
O System normal
Rear 1GbE LAN
(on upper side of jack)
Green
Static
1 Gbps connected
Orange 100 Mbps connected
O 10 Mbps connected/No network
Rear 1GbE LAN
(on lower side of jack)
Green
Static Network connected
Blinking Network active
O No network
Note:
1 Please try to restart your Synology NAS or re-insert the drives, then run the HDD/SSD manufacturer's
diagnostic tool to check the health status of the drives. If you can sign in to DSM, please run the built-in
S.M.A.R.T. test to scan the drives. If the problem remains unresolved, please contact Synology Technical
Support for help.
2 If the ALERT LED continuously blinks red, this indicates there are system errors such as fan failure, system
overheating, or volume degrade. Please sign in to DSM for detailed information.
8Chapter 1: Before You Start
Hardware Specication
Item DS2422+
Compatible Drive Type 3.5"/2.5" SATA x 12
External Port • USB 3.2 Gen 1 x 2
• Expansion port x 1
LAN Port 1GbE (RJ-45) x 4
PCIe Slot Gen3 x8 slot (x4 link) x 1
Size (H x W x D) (mm) 270 x 300 x 340
Weight (kg) 9.5
Supported Client • Windows 7 and 10
• Mac OS X 10.11 onward
File System • Internal: Btrfs, ext4
• External: Btrfs, ext4, ext3, FAT32, NTFS, HFS+, exFAT1
Supported RAID Type • Basic • JBOD • RAID 0 • RAID 1
• RAID 5 • RAID 6 • RAID 10 • Synology Hybrid RAID
Agency Certication • FCC Class B • CE Class B • UKCA • BSMI Class B
• EAC • VCCI • CCC • RCM • KC • UL • RoHS Compliant
HDD Hibernation Yes
Scheduled Power On/O Yes
Wake on LAN Yes
Language Localization
Environment Requirement
• Line voltage: 100 V to 240 V AC
• Frequency: 50/60 Hz
• Operating Temperature: 32 to 104˚F (0 to 40˚C)
• Storage Temperature: -5 to 140˚F (-20 to 60˚C)
• Relative Humidity: 5% to 95% RH
Note: Model specications are subject to change without notice. Please refer to www.synology.com for the latest information.
1Support for exFAT can be enabled by purchasing and downloading exFAT Access in Package Center.
10 Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Ensure a stable environment
with no abrupt changes in temperature or humidity.
Place the unit right side up at all times.
Keep the unit away from liquids.
Before cleaning, unplug the power cord. Do not use chemical or aerosol cleaners. Wipe
with damp paper towels.
To prevent the unit from falling over, do not place it on carts or any unstable surfaces.
The power cord must plug into the correct supply voltage. Ensure the supplied AC voltage
is correct and stable.
Warning, electric shock hazard. To remove all electrical current from the device, ensure
that all power cords are disconnected from the power source.
Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries
appropriately.
Power cord must be plugged into a socket-outlet with earthing connection.
Keep body parts away from moving fan.
This product must be installed by qualied personnel in a restricted access location (like
dedicated equipment rooms, service closets).
Tabla de contenidos
Otros manuales de Almacenamiento de Synology
Synology
Synology NAS DS220+ Manual
Synology
Synology DiskStation DS1517+ Manual
Synology
Synology DiskStation DS213+ Manual de usuario
Synology
Synology DiskStation DS110+ Manual de usuario
Synology
Synology DiskStation DS423 Manual de usuario
Synology
Synology RackStation RS820RP+ Manual
Synology
Synology DiskStation DS1817 Manual
Synology
Synology DS-101j Manual de usuario
Synology
Synology TC500 Manual de usuario
Synology
Synology DiskStation DS2419+ Manual
Synology
Synology FlashStation FS3600 Manual
Synology
Synology DiskStation DS920+ Manual
Synology
Synology DiskStation DS124 Manual de usuario
Synology
Synology DS720+ Manual
Synology
Synology DiskStation DS415+ Manual de usuario
Synology
Synology DS1823XS+ Manual de usuario
Synology
Synology DiskStation Series Manual de usuario
Synology
Synology DiskStation DS119j Manual
Synology
Synology DiskStation DS218 Manual
Synology
Synology DS-106j Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario