Symbol WSS 1000 Manual de usuario
WSS 1000 System
WSS 1000 System
1999-2002 SYMBOL TECHNOLOGIES, INC. All rights reserved.
Symbol reserves the right to make changes to any product to improve
reliability, function, or design.
Symbol does not assume any product liability arising out of, or in
connection with, the application or use of any product, circuit, or
application described herein.
No license is granted, either expressly or by implication, estoppel, or
otherwise under any patent right or patent, covering or relating to any
combination, system, apparatus, machine, material, method, or process in
which Symbol products might be used. An implied license only exists for
equipment, circuits, and subsystems contained in Symbol products.
Symbol and the Symbol logo are registered trademarks of Symbol
Technologies, Inc. Other product names mentioned in this manual may be
trademarks or registered trademarks of their respective companies and are
hereby acknowledged.
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, N.Y. 11742-1300
http://www.symbol.com
Quick Reference
1
Introduction
The WSS 1000 is a wearable data entry system consisting
of a laser bar code scanner, usually worn on the
operator’s fingers or back of hand, and a wrist computer
(WWC 1000) worn on the operator’s forearm.
The detachable components work equally well for right-
and left-handed individuals. Detachable personal mounts
allow multiple operators to share both scanner and wrist
computer without having to use the same mount.
About This Guide
This guide presents information on system components,
assembling the WWC 1000, battery installation and
charging, attaching the system, using the keyboard, and
disassembly for use by others. For wearable scanner
information, refer to the WSS 1000 Product Reference
Guide, or the Quick Reference Guide provided with your
scanner.
2
WSS 1000 System
Parts of the WSS 1000 System
Keyboard
Display
Speaker
Battery
Latch
Power
Switch
Battery Charging
Contacts
Lithium-Ion
Battery
WWC 1000 Top
WWC 1000 (Wrist Computer) Front
Adjustable
Straps Snap-On
Bar
WWC 1000 Wrist Mount
Quick Reference
3
Installing and Charging the Battery
The wrist computer and scanner are powered by a
Lithium-Ion battery pack. The pack provides power for
a typical 8-hour shift.
Note: Before using the wrist computer, install and
fully charge the Lithium-Ion battery pack.
To install the battery pack in the WWC 1000:
1. Insert the battery pack, base first, in the battery
compartment.
2. Line up the pack’s locking mechanism with the
notch in the battery compartment wall by sliding
the battery latch, and press the pack into place.
3. Release the battery latch to lock in place.
Battery
Latch
Notch
Battery
Compartment
Battery Pack
Base
4
WSS 1000 System
Charging the Battery in WWC 1000
To charge the Lithium-Ion battery in the WWC 1000:
1. Place the WWC 1000 in the cradle as shown be-
low:
2. The cradle’s CHARGING light illuminates (RED)
if the WWC 1000 is properly seated and the bat-
tery is charging.
3. The battery requires approximately 2 hours to
charge fully. The CHARGING light changes to
GREEN when the battery is fully charged.
4. To remove the WWC 1000 from the cradle, tilt the
WWC 1000 upward and pull out.
For more information on the CS 1000 Cradle, re-
fer to the CS 1000 Single-Slot Cradle QRG, p/n
70-16237-xx, or the CS 1000 4-Slot Cradle QRG,
p/n 70-17661-xx.
Quick Reference
5
Charging the Spare Battery
Spare battery packs can be charged separate from the
WWC 1000. To charge a spare battery pack in the cradle:
1. Insert the pack in the cradle’s spare charging slot.
2. The CHARGING light illuminates red.
3. The spare pack is charged in approximately two
hours, even if the WWC 1000 is charging at the
same time. The CHARGING light changes to
green when the battery is fully charged.
6
WSS 1000 System
Assembling the WSS 1000 System
To assemble the WWC 1000 (wrist computer):
1. Place the WWC 1000 wrist computer onto the
wrist mount, facing you. Be sure the mount is ori-
ented so that the longer strap will be further up the
forearm.
2. Snap the bar over the WWC 1000 using the snaps
on either side of the mount. The straight part of the
bar should lay across the front of the WWC 1000;
the curved part in back.
Quick Reference
7
Note: The snaps on the wrist mount act as a tear-
away device allowing the wrist computer to
detach from the mount if it catches on an
object.
3. Plug the cable connector from the WWC 1000 in
the interface port on the back of the scanner.
4. Place the WWC 1000 on your arm:
a. Slide the wrist mount on your arm, so that the
WWC 1000 wrist computer faces you.
8
WSS 1000 System
b. Pull the straps through the buckles so the wrist
mount is secure but not tight.
c. Use the Velcro to secure the straps.
5. Assemble and mount your scanner. See your scan-
ner’s Quick Reference Guide, or the WSS 1000
Product Reference Guide.
Otros manuales para WSS 1000
2
Tabla de contenidos
Idiomas:
Otros manuales de Lector de código de barras de Symbol
Symbol
Symbol LS 2104 Instrucciones de funcionamiento
Symbol
Symbol LS 4208 Manual de usuario
Symbol
Symbol LS2208-SR20001R Manual de usuario
Symbol
Symbol LS-2100U Manual de usuario
Symbol
Symbol LS 400 series Manual de instalación y operación
Symbol
Symbol LS1900 Series Manual de usuario
Symbol
Symbol DS3478 Manual de usuario
Symbol
Symbol SYMBOL MINISCAN MSXX04 Guía de configuración rápida
Symbol
Symbol LS 2000MX series Manual de usuario
Symbol
Symbol CRD3100-1000 Manual de usuario
Symbol
Symbol DS6707-SR20007ZZR Manual de usuario
Symbol
Symbol DS 3408 Manual de instalación y operación
Symbol
Symbol LS4278 Manual de usuario
Symbol
Symbol LS 4208 Manual de usuario
Symbol
Symbol LS 4071 Manual de usuario
Symbol
Symbol LS 3070 Manual de usuario
Symbol
Symbol LS9203 Manual de instalación y operación
Symbol
Symbol Symbol LS2208 Manual de usuario
Symbol
Symbol LS1203 Manual de usuario
Symbol
Symbol LS-3203ER Manual de instalación y operación
