SWIT BM-215NDI Manual de usuario

Model：BM-215NDI、245NDI

User Manual

Ver：AThank you for choosing SWIT products, please read this user manual seriously before using. SWIT ELECTRONICS CO., LTD.01 4K Studio LCD MonitorBM-NDI R

Statement Any internal technology (including hardware equipment, software design and product trademark) of the product shall be protected by law, and any infringement of intellectual property rights of the product shall be investigated for legal liability。All the brand and trademark in this product are protected by law,all other company’s brand and trademark in this product are protected by their owner’s law. In order to better service majority users,SWIT products will keep improving and developing,SWIT keep the right to revise and improve this user manual without previous notice. The warranty period of this product are two years,the following condition are not covered by the warranty: ⑴ The appearance and the LCD panel are damaged by man-made out force；⑵ The amount of defective pixels are under three；⑶ The product is damaged by using incompatible power adaptor；⑷ The product is damaged by failure to use, maintain or storage according to the user manual.；⑸ The product is disassembled by user in the process of using；⑹Other faults or damages not caused by design ,technology,manufacture and quality.＊Any sales person have no right to provide extra warranty beyond these terms. Please feel free to contact with us by phone,fax or email when you have any question or need any help in the process of using. ⸻ This user manual applies to all BM-NDI model monitor,all the illustration take BM-215-NDI for example,any diﬀerence of speciﬁcation or appearance,this manual will be attached text explanation;⸻ The function with mark ”#” in this user manual have not been realized yet.SWIT Electronics Co., Ltd.Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone, Nanjing 210038, P.R.ChinaPhone: +86-25-85805753Fax: +86-25-85805296Email: cont[email protected]http://www.swit.cc02

AttentionWarning1. Do not put the monitor in rainy or wet environment to avoid the dangerous of ﬁre or electric shock；2. Do not put the monitor close to any device with high-intensity magnetic. Warning of power connection1. Please using original power adaptor to avoid damage；2. When using other DC power ,make sure the range of voltage,output power and polarity of it meet requirements；3. Please cut oﬀ the power including AC power cable or battery under below conditions: （A）、If the monitor will not be used for a long time. （B）、If the power cable or power socket is damaged.。（C）、If the housing of the monitor is broken by out-force or falling. Warning of using 1. Do not touch the surface of screen directly to avoid damage,also the ﬁngerprint on the screen will be hard to clean. 2. Do not put pressure on the LCD screen because LCD screen is fragile；3. Do not put the monitor on anywhere unstable to avoid falling.Maintenance and cleaning1. Use soft dry cloth and LCD screen clean liquid to clean the dust and stain on the screen. 2. Do not put pressure on LCD screen when doing cleaning. 3. Do not clean the LCD screen by water or other chemical liquid to avoid damage. 03

OverviewThe resolution of BM-NDI series LCD monitor is up to 1920*1080, H178°/ V178° super wide angle of view，support 2* 3G/HD/SD-SDI input 、1* HDMI 2.0 input and 1* NDI input，1* 3G/HD/SD-SDI loop out、1* NDI to SDI loop out，1* 3.5mm jack input and speaker. Features: 1920×1080 HD resolution；Support NDI signal input、multi signal source input；Support 16 channel embedded audio bar,any of two channel can be chosen to output；Waveform Y/Cb/Cr/R/G/B/RGB, support single line waveform；Support vector scope、R/G/B/Y histogram、red/blue focus assist；Support 3DLUT（17x17x17）Auto self-calibration；Support TSL UMD and text TALLY（TSL 3.1/4.0）；Safety Marker：4:3/13:9/14:9/15:9/16:9/1.85:1/2.35:1/2.39:1/2:1/User 1/User 2；Support USB ﬁrmware update and LOG ﬁle uploading（The format of USB driver should be FAT 32）；Support Green mode. Packing listStandard accessoriesMonitorBattery plate（V-mount or Gold-mount）Monitor standPower cableQuantities

1No.123404Table of contentsStatement Attention Table of contentsPacking listProduct featureInstruction Front panel view Back side view OSDStatusOperation The menu contentDimensionSpeciﬁcationTroubleshoot23444557891010181922

05Instruction·Front panel view（1） Tally light：Can be set to red, green and yellow；（2） Speaker：Can play embedded audio of HDMI、SDI and NDI.（Speaker will not work when earphone is connecting）；（3） Desktop stand feet ;（4） User1~User4：In order to quickly enter in the mode which was preset already .Hold the shortcut button to save current user setting.Speciﬁc please see “The menu content-Ⅷ. System” ；（5） INFO：Press ”INFO” to remove or recover all current function in display like status information and A/V analyzed pattern；Press “INFO” to exit menu when the menu is on；（6） F1~F5 Function key：User can set these function key to diﬀerent function according to their requirement；(1)(2)(3)(4)(5)(6)(7)(8)(9)(10)(11)

06（8） Menu/Enter：When menu is oﬀ,press the button directly to open the Main Menu；rotate “MENU” to choose diﬀerent setting selection or adjust the value；press the knob to conﬁrm the setting；（9） LUT/Firmware：Firmware update or LUT ﬁle upload；（10）PHONE：3.5mm jack input，monitor embedded SDI and HDMI audio signal；（11）Power：power switch.(7)Brightness Contrast Saturation

Backlight Volume Source Brightness：Brightness control,Range:-100~100，Default value:0Contrast：Contrast control,Range:-100~100，Default value: 0Saturation：Saturation control,Range:-100~100，Default value:0Backlight：Backlight control,Range:0~100，Default value:16Volume：Volume control,Range:0~100，Default value:36Source：Input signal source selectionPress “Brightness”、”Contrast”、”Saturation、Backlight”、”Volume” on the front panel to choose corresponding functions,turn “MENU” knob left and right to control the corresponding value。If no operation is performed within 5 seconds,the selection will automatically cancelled,the button light will oﬀ;long press to recover to default value；long press the “VOLUME” button to enter in mute mode.“NDI Source” and “NDI setting” in the menu is to choose the input source under NDI channel,here are the details:1. NDI Source：Detect and show all NDI device and all NDI signal name of NDI device in the same network,turn “MENU & ENTER” to change diﬀerent signal source. 2. NDI Setting：Set the IP address of secondary network device of monitor to be able to detect secondary device and the signal source.

07·Back side view（1）SDI IN1/2： 3G-SDI （2）NDI-SDI loop out：3G-SDI（3）SDI loop out：3G-SDI（4）NDI IN：12G /3G-SDI（5）HDMI 2.0 IN：The DHCP protected content is not displayed（6）Reset: Formatting button Instruction（Do not do this without SWIT permission）：1. Switch oﬀ monitor；2. Touch and keep pressing the small button with suitable tool （Do not release it when switch on monitor）；3. Switch on monitor with “POWER” button，Tally light will show red light （release the reset button after tally light shows red light）；4. Wait for 5~10s，Tally light shows green；5. Reboot monitor to ﬁnish resetting. （7） RS485 #：TSL UMD control port（8） GPI #：GPI control port（9） Fan（10）DC IN：12V～17V（11）AC IN：100V～240V（12）Battery plate：Support V-mount battery or Gold-mount battery(1)(2)(3)(4)(5)(6)(7)(8)(9)(10)(11)(12)

⑴ Time code（SDI）Display the information of time code which is embedded in SDI signal（LTC，VITC1&2），moni-tor will show “TC:UNLOCKED” if no time code information is detected.User can set shortcut key（F1~F5） or GPI pin to “time code” function，in order to quickly switch on/oﬀ this function.⑵ On screen TALLYThe tally signal is controlled by GPI. ⑶ Source ID/UMDDisplay/UMD（TSL3.1/4.0），user can set in the UMD menu. ⑷ Lissajous patternLissajous pattern will show audio signal，user can set shortcut key（F1~F5） or GPI pin to “Lissajous pattern” function，in order to quickly switch on/oﬀ this function. ⑸ WaveformUser can switch on/oﬀ “Waveform” function or choose diﬀerent type of waveform by setting shortcut key(F1~F5) or GPI pin to “Waveform” function on the front panel.The parameters such as on-screen-position,transparency and color of “waveform” can be set in MENU. ⑹ Vector scopeUser can switch on/oﬀ “Vector scope” function by setting shortcut key(F1~F5) or GPI pin to “Vector scope” on the front panel.The parameters such as on-screen-position,transparency and color of “Vector scope” can be set in MENU. ⑺ Audio meterIn order to monitor audio signal，User can switch on/oﬀ “Audio meter” function by setting shortcut key(F1~F5) or GPI pin to “Audio meter” function on the front panel. The parameters such as on-screen-position, transparency and numbers of audio channel of “Audio meter” can 08·OSDin phase

TC 00:15:13:07

CAMERA (1)

(2)

(3)(4)(5)(6)(7)(8)

09Status be set in MENU. ⑻ HistogramUser can switch on/oﬀ “Histogram” function by setting shortcut key(F1~F5) or GPI pin to “Histogram” function on the front panel. (1)(6)(5)(7)(8)(4)(3)(2)

Main MenuExit&Status >Input >Picture > Color Management >Scanning >Control >Assist >De-embed >Auto Calibration >NDI Source >NDI Settings > Multiview Setting >

StatusFormatChannelColor TempF1F2F3F4F5Loaded ProﬁleNetworkVersion XXHost Name XX XX XX XXXXXXXXXXXXXXXXX XX XXPress “Menu/Enter”，the menu will show in the top left corner of screen，“Exit & status” will show current working status of monitor. ⑴ FormatShow current input signal format；Will show “NO SIGNAL” when there is no recognizable input signal”.Will show the format of current SDI source when the input source is SDI. ⑵ Channel Show current chosen input source.⑶ Color temp Show current color temperature. ⑷ Function Key F1~F5 Show the function of Key F1~F5. (5) Loaded Proﬁle Show current user mode.(6) Network Show the connection status of Internet. （7）Version Show version of current ﬁrmware .（8）Host name Show the model of this monitor.

10OperationThe menu contentSteps1、Press “Menu/Enter” knob，the menu will show on top left corner of screen.2、Turn “Menu/Enter” left and right to choose diﬀerent sub-menu,the chosen one will show yellow backlight,press“Menu/Enter” knob to set the corresponding parameter. 3、Turn “Menu/Enter” knob left and right to set corresponding parameter，press “Menu/Enter”knob， the chosen one will show yellow backlight. 4、Turn “Menu/Enter” knob left and right to set corresponding parameter,press “Menu/Enter” knob to save the setting after ﬁnish adjustment.5、Turn “Menu/Enter” knob to choose “EXIT”，press “Menu/Enter” knob，exit the sub menu,choose “EXIT & STATUS” in the main menu,press “Menu/Enter” knob to exit main menu.Attention＊ The options which shown grey can not be set. ＊ The menu will save and exit automatically when no operation is performed within a period of time. “The menu content” will introduce the speciﬁc contents of setting in menu and sub-menu,the menu option which is noted with “ * ” will be explained in detail under the list. Ⅰ、Input—Set the color of input video Menu optionInput range *1YUV Color MatrixRed GainGreen GainBlue GainRed Bias Green BiasBlue Bias ResetInstructionSet the input range of videoChoose YUV Color MatrixAdjust the value of Red GainAdjust the value of Green Gain Adjust the value of Blue Gain Adjust the value of Red Bias Adjust the value of Green Bias Adjust the value of Blue Bias Reset the value of Gain and Bias The range of value0-1023,4-1019,64-940，64-1023Auto，BT.601，BT.709，BT.2020-100 ~ +100-100 ~ +100-100 ~ +100-100 ~ +100-100 ~ +100-100 ~ +100/*1 Input rangeSet the input range to compatible with input video signal,the default input range is 64-940 which is compatible with broadcast application program. Ⅱ、Picture *1—Set the display of input video Menu optionContrastBrightnessSaturationSharpnessBacklightInstructionAdjust the contrast of videoAdjust the brightness of videoAdjust the saturation of videoAdjust the sharpness of videoAdjust the backlight of videoThe range of value-100 ~ +100-100 ~ +100-100 ~ +1000 ~ +1000 ~ +100