Swiftech MCW5000-P Manual de usuario

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769

Page 1 of 2

Parts list

Parts QTY PARTS QTY

MCW5000-P™ assembly 1 Spring clips 2

Tube inserts 4 Arctic Alumina Thermal compound 1

Tube removal tool 1 Hex L-key 1

This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation may result in damage

to your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The

following instructions are subject to change without notice. Please visit our web site at www.swiftnets.com for updates.

1. Before you install the MCW5000-P™water-block:

a. Prepare two pieces of tubing of sufficient length to connect

to the rest of your circuit. The cuts must be square as shown in

figure 1 or leaks may occur:

b. Install the provided plastic tube inserts at each end of the tubes,

as shown in figure 2: these inserts are absolutely imperative when

using any kind of soft tubing, such as vynil, ClearFlex, Taigon, etc...

Square cut

Figure 1 Figure 2

Figure 3

Figure 4

Figure 5

c. Spread a little bit of grease (Vaseline etc..)

around the tubing. It helps pushing the tubes in,

particularly with Clearflextubing, which

features a very “sticky” surface.

d. Fully insert both tubes into the fittings. The tip of the plastic tube inserts should

be flush with the inlet and outlet openings, as shown in figure 4 above. Inserting the

tubes requires a firm push, accompanied by a twisting motion.

Block orientation (rotating the stainless steel frame to change the inlet/outlet orientation):

The MCW5000™ can be installed in any direction that suits your needs.

Removing the 4 socket screws that attach the frame to the block will allow

you to rotate the frame 90°, so that inlet and outlet face up and down

instead of left and right. This doesn’t affect the performance of the block,

nor the ability to bleed it appropriately.

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769

Page 2 of 2

2. Preparing your Motherboard

a. Remove the existing heat sink

b. Carefully clean the CPU.

c. Lightly coat the CPU with the provided thermal compound. Only a paper-thin coat is necessary. It should be applied using

preferably a razor blade, or a credit card, held between thumb and index at a 45-degree angle.

3. Installing the MCW5000-P™ water-block in Pentium4 socket 478 stock retention frame:

Step 1

Step 2

Step 3

Position your block inside of the

retention frame, and put both clips in

place for the next steps, by simply

slipping the non thumb-tabbed end of

each clip in the retention frame’s locking

holes.

While maintaining the opposite side of the

block to prevent it from tipping over, push

down on the thumb-tab to hook the first

clip to the retention frame’s locking hole.

While still maintaining pressure on the

block, hook-down the second clip.

Installation is complete!

Removing the block: simply reverse the procedures described in steps 2 and 3 above.

4. Connect the block to the rest of the cooling circuit.

The block is designed in such a way that it will bleed itself automatically in any vertical orientation (computer standing-up).

5. Final inspection

Once the installation is completed, it is always a good idea to test the circuit for leaks, prior to powering up the computer.

Troubleshooting help is available on our web site at www.swiftnets.com, or by calling customer support at 562-595-8009.

Note concerning removal of the tubing: Push in collet squarely against face of fitting. A tube removal tool is provided with the

MCW5000 block. With the collet firmly held against the face of the fitting, the tube can be safely pulled out. Do not attempt to pull the tube out

without pushing squarely against the collet. This may result in damaging the fitting. Further details for using quick-connect fittings are also

available here: http://www.johnguest.com/install_6.shtm#disconnect:

Tabla de contenidos

Otros manuales de Hardware de computadora de swiftech

swiftech

swiftech MCW5000-64 Manual de usuario

swiftech

swiftech MCW5000-64RH Manual de usuario

swiftech

swiftech MCW5000-PX Manual de usuario

swiftech

swiftech Stealth Manual de usuario

swiftech

swiftech MCW82 Manual de usuario

swiftech

swiftech MCW40-T Manual de usuario

swiftech

swiftech MCB120 Radbox Manual de usuario

swiftech

swiftech MCW5000-64 Manual de usuario

swiftech

swiftech MCW20-A Manual de usuario

swiftech

swiftech POLARIS Series Manual de usuario

swiftech

swiftech MCP35X RESERVOIR Manual de usuario

swiftech

swiftech MCP35B Manual de usuario

swiftech

swiftech MCX370-A Manual de usuario

swiftech

swiftech Obsidian Manual de usuario

swiftech

swiftech Stealth Manual de usuario

swiftech

swiftech MCX462+ Manual de usuario

swiftech

swiftech Maelstrom 5 1/4 Dual Bay Reservoir Series Manual de usuario

swiftech

swiftech MCW5000-PX Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

swiftech MCW5000-P Manual de usuario

Manuales populares de Hardware de computadora de otras marcas