Swann SWIFI-FLOCAM2 Manual de usuario

Wi-Fi Floodlight Security Camera

Cámara de seguridad con Reflector Wi-Fi

Caméra de sécurité à Projection Wi-Fi

EN Quick Start Guide ES Guía de inicio rápido FR Guide de démarrage rapide

SWIFI-FLOCAM2

• Install the product in accordance with local and national electrical codes. If you have any doubts or

questions about the electrical connections or if you need an electrical junction box installed, contact

a licensed electrician. In certain jurisdictions, this product needs to be installed by a licensed

electrician. Check with local authorities for applicable requirements.

• The product must be mounted on a flat vertical surface capable of supporting the full weight of the

product.

• Ensure the voltage marked on the product is the same as the electrical power supply to be used.

• Do not connect to a dimmer switch or timer.

• Always turn off electricity at the main circuit breaker or fuse box before installation. Failing to do so

could result in serious injury, electrical shock, and/or risk of fire.

• Do not rely on the wall switch alone to turn off the power.

• Do not open or disassemble the product. There are no user-serviceable parts inside.

IMPORTANT SAFETY INSTRUCTIONS

• Before you begin the installation of the product, it is important that you confirm the availability of

Wi-Fi as well as the signal level at the desired installation location.

• Note that Wi-Fi quality can vary significantly at different locations around the home due to

environmental factors such as home construction type and wireless interference from other

electronic devices.

TO CHECK WIFI COVERAGE

1Connect your phone to the 2.4GHz Wi-Fi network band of your internet/broadband router.

Note: The Swann Floodlight Security Camera will only connect to a 2.4GHz network.

2Place your phone where you are planning to install the floodlight unit. If you have Wi-Fi connection

on your phone, the camera will also likely be able to obtain Wi-Fi connection. Check the Wi-Fi icon

on your phone. We recommend a minimum of 1 bar showing on your phone's Wi-Fi icon as shown

below. Further testing should be performed if the Wi-Fi signal strength is only 1 bar.

PREINSTALLATION CHECK

WIFI COVERAGE AVAILABILITY

0 1

Number of bars indicate

Wi-Fi signal strength

ExcellentGoodFairPoorNo connection

2 3 4

PREINSTALLATION CHECK

3To avoid any potential Wi-Fi connection issues later, try playing a video on a media streaming

service app, for example, YouTube™or Netflix™, through your phone. If possible, temporarily pause

activities like online gaming and video streaming on other devices connected to your network

while you perform testing, as this can affect the connection speed and quality.

4If you don't experience any video streaming issues (buffering, stuttering, etc), you can proceed with

the installation of the product. There are also Wi-Fi surveying and speed tools available online that

can help you analyze and test the quality of your Wi-Fi connection including download and upload

speeds (minimum internet upload speed of 1 Mbps is recommended for optimal video streaming).

5If you still have any concerns about your Wi-Fi coverage, consult a licensed electrician on

connecting the Floodlight wiring to a temporary plug and running an extension cord to a wall

outlet so you can power the camera onsite to test Wi-Fi pairing and live video streaming directly

via the Swann Security app. For camera pairing instructions, see page 9.

WIFI WEAK OR OUT OF RANGE

• If you're getting a weak Wi-Fi signal or you can’t connect to Wi-Fi at all on your phone at the

installation site, we recommend moving your router closer, installing a Wi-Fi extender (which can

help improve signal reception) or selecting another location.

• Do not proceed with the installation of this product until you have thoroughly tested and

confirmed the availability and reliability of the Wi-Fi connection at your desired location.

GET THE APP

1Download the latest version of the Swann Security app from the Apple App Store® or Google

Play™ Store on your iOS or Android device. Simply search for "Swann Security".

2Open the app, create your Swann Security account, and sign in. You will need to activate your

account by confirming the email sent to the email account you provided before you can sign in.

GET THE APP

INSTALLATION EXAMPLE DIAGRAM

Slow Blinking Blue Wi-Fi Pairing Mode Solid Red Live streaming/Motion recording

Fast Blinking Blue Connecting to Wi-Fi Blinking Purple Low Wi-Fi signal

LED Indicator Guide

Resetting the Camera

Open the port cover on the back of the camera. Press and hold the Reset button for 10 seconds.

GND

Microphone

Washer

Cap

Night Detection Sensor

Adjustment KnobLocking Nut

Foam Gasket

Junction Box

(not included)

Infrared LEDs LED Indicator

Speaker (Siren)

True Detect™

Passive Infrared (PIR)

Motion Sensor

Locking Collar

Reset Button

Wire nut

(Live)

(Neutral)

(Ground)

Black

White

Green/Yellow

Floodlight wiring

INSTALLATION INSTRUCTIONS

IMPORTANT! TURN POWER OFF AT CIRCUIT BREAKER OR FUSE BOX.

When installing the unit refer to the Installation Example Diagram on page 6.

1If you're replacing an old floodlight, disassemble it along with any existing mounting bracket

from your junction box and disconnect the wire connections.

CAUTION: Before handling any wiring, use a circuit tester to confirm that the power is off.

2Attach the provided mounting bracket to your junction box using the provided screws. The side

of the mounting bracket marked "GND" should be facing out.

3Peel the backing off the adhesive foam gasket and stick it to the back of the floodlight unit.

4Connect individual supply wires from the junction box to the floodlight unit using the provided

wire nuts. Pair the black supply wire with the black floodlight wire, the white supply wire with

the white floodlight wire, and the bare or green supply wire with the green/yellow floodlight

wire. (For reference, see Power circuit wiring color codes table on the next page.) Make sure

the ground wire is also screwed to the "GND" threaded hole of the mounting bracket with the

green ground screw.

This unit is designed to be mounted on a standard wiring junction box and requires connection to a

100-240VAC power supply. For optimum results, install the unit at least 2.4m (8ft) above the ground.

Read "IMPORTANT SAFETY INSTRUCTIONS" and "PREINSTALLATION CHECK"and make sure the

installation site is Wi-Fi ready before installing the unit.

INSTALLATION INSTRUCTIONS

5After wires are connected, carefully tuck them inside the junction box.

6Place the floodlight unit (make sure the "UP" arrow on the back is pointing up) against the junction

box aligning with the center hole of the mounting bracket and lock it securely with the provided

long bracket screw and washer.

7Insert the provided screw cap firmly into the center mounting hole on the floodlight unit.

8Apply silicone weather sealant (not included) around the mounting surface of the floodlight unit

and junction box for moisture seal. Installation is complete. Remove the protective film from the

camera.

9Turn the electricity back on and allow the camera to power up. This can take up to a minute.

When the camera starts blinking blue, it is ready to be paired with your Wi-Fi network.

LIVE (HOT) NEUTRAL GROUND (EARTH)

Black

White

Bare copper or green

If wiring colors do not match — a common

issue in older homes — contact a licensed

electrician who will be able to help you check

and identify the electrical wiring. Do not guess the

wires. Incorrect wire connection will damage the

unit and could cause fire or injury.

Power circuit wiring color codes

TIP If you have a light switch that controls the floodlight unit, remember not to turn off the switch as

this will also turn off the camera. The camera needs to be powered at all times to stay connected

to your Wi-Fi. Put a sticker label on the light switch so that people know not to turn it off.

Learn more about using your Swann Floodlight security camera, such as viewing live video and event

clips as well as adjusting camera settings including floodlight brightness and siren duration, by

downloading the Swann Security manual from the app menu .

SET UP THE CAMERA

Open the Swann Security app on your phone and sign in. Tap the Pair Device button on the screen (or

open Menu and select Pair Device) and follow the in-app instructions to set up your new camera.

TIPS

Angle Adjustments

To adjust the direction of the lamps and the camera, loosen the corresponding adjustment knob or locking nut/collar.

Less

sensitive

Motion Detection

• The camera's motion sensor is more sensitive to

the movement of heat across the coverage area

and less sensitive to movement directly towards

or away from it.

• Position the camera tilted slightly downwards so

that the likely approach path occurs across the

coverage area (see figure on right). When walking

directly towards or away from the motion sensor

the detection range will be reduced. Note that

detection range may also alter with changes in

ambient temperature.

TIPS

Otros manuales para SWIFI-FLOCAM2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Cámara de seguridad de Swann

Swann

Swann Xtreem Manual de usuario

Swann

Swann NHD-810 Manual de usuario

Swann

Swann SW215-DMD Manual de usuario

Swann

Swann ADW-300 Manual de usuario

Swann

Swann SwannCloud ADS-446 Manual de usuario

Swann

Swann NightVision BulletCam Manual de usuario

Swann

Swann Color dome camera Manual de usuario

Swann

Swann NHD-819 Manual de usuario

Swann

Swann HD-420 Manual de usuario

Swann

Swann PRO-754 Manual de usuario

Swann

Swann PRO-750 Manual de usuario

Swann

Swann Maxi-Brite Cam F-SW244-LPC Manual de usuario

Swann

Swann DIY Security Cam SW211-DSX Manual de usuario

Swann

Swann Black Knight SW-C-BLACKK Manual de usuario

Swann

Swann SWIFI-SPOTCAM Manual de usuario

Swann

Swann A851 Pro-Series Manual de usuario

Swann

Swann SWWHD-PTCAM Manual de usuario

Swann

Swann PRO-650 Manual de usuario

Swann

Swann A851 Manual de usuario

Swann

Swann BulletCam SW213-BCC Manual de usuario

Swann

Swann SWIFI-CAM Manual de usuario

Swann

Swann SwannOne SoundView SWO-SV02K Manual de usuario

Swann

Swann PRO-530 Manual de usuario

Swann

Swann PRO-770 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario