Swagelok RS20 Manual de usuario

RS(H)20, 25

USER MANUAL

Read the complete manual before installing and using the regulator.

WARNING

Before removing a regulator from the system for service, you must

depressurize system

purge the system to remove any residual system media left in the regulator.

CONTENTS

Introduction................................................................................................................................................ 3

Installation ................................................................................................................................................. 4

Operation ................................................................................................................................................... 5

Maintenance .............................................................................................................................................. 6

Testing ....................................................................................................................................................... 6

Troubleshooting ........................................................................................................................................ 7

Introduction

Representative drawing of a standard RS20

1 body 13 valve spring 24 springguide

2 springhousing assembly 14 conical spring 25

3 bodyplug 15 26 set spring

5 valve assembly 16 diaphragm 27 setscrew

7 bodyplate 18 28 nut

8 diaphragm plate 19 29 socket head cap screw

9 bottom springguide 20 o-ring 30 ring

10 seat 21 o-ring

11 22

12 retaining ring 23 ball

Installation

WARNING

When installing a Swagelok self-venting regulator, position the vent connection or line away from

operating personnel. Operating personnel must protect themselves from exposure to system

fluids.

CAUTION

Do not use the regulators as a shutoff device

The preferred mounting position of the regulator is horizontal with the spring housing facing upwards.

The standard connection of the RS(H)20 is 1" bspp parallel female. To get a proper sealing across the

thread, Swagelok recommends using bonded seal rings.

If earthing is required, connect an earth wire under a spring housing bolt.

Operation

Note: All handle directions are when viewed from above.

Outlet and control pressure settings are obtained by adjusting the set screw with a 19 mm open end

wrench.

To increase the outlet or control pressure, rotate the set screw clockwise.

To decrease the outlet or control pressure, rotate the set screw counter-clockwise and vent the

downstream side of the regulator.

Make the final setting in the direction of increasing pressure to obtain the most accurate set

points.

Once fluid is flowing through the system, fine tuning may be required.

Icing of the regulator at high flow rates or high pressure drops may occur if the gaseous media or

atmosphere contains moisture.

An auxiliary upstream filter is recommended for use in all but the cleanest of media.

Installation of a downstream pressure relief is recommended for regulator and system protection.

If the shut-off valve at the outlet side is closed after changing the set pressure, the outlet pressure will

rise a little because of the closing force required for bubble-tight closing of the regulator.

This phenomenon is usually referred to as the “lock-up” and does not indicate a problem with

the regulator.

A decrease in the flow will result in a rise of the outlet pressure.

An increase in the flow will result in a fall of the outlet pressure and is usually referred to as the

“droop”.

This phenomenon does not indicate a problem with the regulator.

A decrease of the inlet pressure will result in a rise of the outlet pressure.

An increase of the inlet pressure will result in a fall of the outlet pressure.

This phenomenon is usually referred to as the “dependency” or “supply pressure effect” and

does not indicate a problem with the regulator.

CAUTION

When using the RSH(F)20, 25 with an inlet pressure higher than 200 bar, a safety valve must be

installed in the outlet line, because the outlet pressure may not exceed 200 bar.

Maintenance

Required tools for maintenance

a vice to fasten the regulator

pincers to take out the o-rings

a pair of tongs for a retaining ring 70 mm (RS20)

a torque wrench

a torque wrench hexagon head key 10 mm

a torque wrench “open end insert tool”, 46 mm

an open end wrench, 18 mm

media and temperature compatible lubricant for reassembling threaded parts

media and temperature compatible lubricant for o-rings

▪Snoop®liquid leak detector

Disassembly instructions

Loosen the hexagon socket head screws and remove the spring housing, set spring, bottom

springguide.

For diaphragm sensing versions the diaphragm and diaphragm plate can be removed.

For piston sensing versions, the piston plate and the piston can be removed.

Loosen the bodyplug and remove the valve, valve spring and seat.

Inspection of disassembled parts

Check all parts for abnormal wear. Replace parts in case of doubt.

Points of attention before assembly

All parts must be clean and undamaged before starting assembly.

Swagelok recommends replacing all o-rings and the diaphragm before assembly.

All threaded parts must be lightly lubricated before assembly, this to avoid galling of threads.

All o-rings need to be lightly lubricated to improve the lifetime of the o-ring and the performance of the

regulator.

Assembly instructions

Follow the points for disassembly in reverse order to assemble the regulator.

Recommended torques

▪Hexagon socket head screws M12 80 N·m (707 in. ·lb)

▪Bodyplug 50 N·m (442 in. ·lb)

Testing

Check the regulator for leakage across the seat, with low- and high inlet pressure.

Check the regulator for leakage across the diaphragm/piston, with low- and high outlet pressure.

Check the required outlet pressure range.

A well performing RS(H)20, 25 is 100% bubble tight.

If there is a leakage across the seat or the diaphragm/piston, the damaged parts must be replaced.

Troubleshooting

Problem: The outlet pressure creeps up, without turning the set screw.

Cause: A damaged valve and/or seat.

Solution: Replace the valve and/or the seat.

Problem: Leakage around the bodyplug.

Cause: A damaged o-ring or insufficient torque on the bodyplug.

Solution: Replace the o-ring or tighten the bodyplug according to the torque specifications.

Problem: Leakage between the body and the spring housing or through the relief hole at the side of the

spring housing.

Cause: A damaged diaphragm/piston o-ring or insufficient torque on the bolts.

Solution: Replace the diaphragm/piston o-ring or tighten the bolts according to the torque specifications.

Problem: Controlled pressure drops off sharply even when the flow is within regulator capabilities.

Cause: The system filter element is clogged.

Solution: Replace the system filter element.

Problem: The required outlet pressure can not be reached.

Cause: The inlet pressure is not high enough.

Solution: Make sure that the inlet pressure is sufficient.

Problem: The outlet pressure rises too much when going from a dynamic to a static situation.

Cause: There is too much flow in the dynamic situation.

Solution: A larger regulator is required.

Check the specific application data with the flow curves in our documentation, if available.

Problem: The outlet pressure does not drop if the set screw is turned counterclockwise.

Cause: The regulator is non-venting.

Solution: A shut-off valve in the outlet line must be opened to reduce the outlet pressure.

Problem: The outlet pressure has changed without turning the set screw.

Cause: Changes to the inlet pressure will result in changes to the outlet pressure.

A decrease of the inlet pressure will result in a rise of the outlet pressure.

An increase of the inlet pressure will result in a fall of the outlet pressure.

Solution: Maintain a constant inlet pressure to the regulator. See section “operation” about dependency.

Warranty Information

Swagelok products are backed by The Swagelok Limited Lifetime Warranty.

For a copy, visit swagelok.com or contact your authorized Swagelok representative.

For additional information, see www.swagelok.com. Swagelok, Snoop®– Swagelok Company

January 2011, R1

MS-CRD-0189

Caution: Do not mix or interchange parts

with those of other manufacturers.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Swagelok

Swagelok

Swagelok BS2 series Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok KFB Series Especificaciones técnicas

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok KBP Series Especificaciones técnicas

Swagelok

Swagelok KLF Series Manual de usuario

Swagelok

Swagelok KPR Series Especificaciones técnicas

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok TBVS8 Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok RS Series Manual de usuario

Swagelok

Swagelok KHB Series Especificaciones técnicas

Swagelok

Swagelok KSV Series Especificaciones técnicas

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok BS20 Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok KPF Series Especificaciones técnicas

Swagelok

Swagelok KCB Series Especificaciones técnicas

Swagelok

Swagelok RDH10 Series Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok KPP Series Especificaciones técnicas

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario