Swagelok KPP Series Especificaciones técnicas
Kit Contents
KPP Series Regulators
Maintenance Instructions
Seat
Inlet lter
Piston seal and spring
Lubricant
MS-LT-WL8
Poppet spring
Body seal and spring
Poppet
Symbols
Lightly lubricate
Discard
Seat retainer
Poppet damper
Piston seal retainer
Tools Required
Tool Size Component
Vise
- Body
Socket
11/16 in. or 17 mm Stem nut,
Antitamper nut
5/8 in. or 16 mm Seat retainer
Crow’s Foot
2 in. or 50 mm Cap ring
Open-ended wrench
2 in. or 50 mm Cap ring
Torque wrench
Capable of
100 ft·lb (135 N·m, 13.8 m·kg)
Seat retainer,
Cap ring
Swagelok Tools Available
Piston seal insertion tool
-Piston seal and spring
Body seal insertion tool
-Body seal and spring
Filter insertion tool
-Inlet filter
Filter pick tool
-Inlet filter
Note: See Pressure Regulators, MS-02-230, for tool ordering information.
2
Exploded View
3
Note: Plated steel spring buttons shown.
Assemblies with the 316 SS spring buttons do not include the spring stabilizer.
Cover
Stem nut
Handle
Body cap
Cap ring
Stem
Body seal and
spring
Body
Upper spring button
Range spring
Lower spring button
Spring stabilizer
Seat
Seat retainer
Poppet
Poppet spring
Poppet damper
Piston seal and spring
Piston seal retainer
Piston
Inlet lter
Piston guide
Seat Assembly
6. Push the piston out of the piston guide.
7. Remove the piston seal and spring and the piston seal
retainer from the piston guide, and the body seal and
spring from the body.
NOTICE
Do not damage the inner diameter of the piston
guide. Leakage could result.
8. Loosen and remove the seat assembly. Discard the seat
and seat retainer.
NOTICE
Be careful not to scratch the inside of the body.
Leakage could result.
WARNING
Before removing a regulator from the system for
service, you must
• depressurizesystem
• purgethesystemtoremoveanyresidual
system media left in the regulator.
Disassembly
1. Place the regulator in a vise.
2. Turn the handle counterclockwise until it stops.
Note: If using an antitamper nut, remove it from the body.
Then turn the stem counter clockwise until it stops.
3. Loosen the cap ring.
4. Remove the cap assembly and handle as one piece and
set aside for later use.
Note: The range spring and the lower spring button may
fall from the cap assembly. Set aside for later use.
5. Lightly grip the piston guide in the vise and remove the
body.
NOTICE
Twist the body gently to avoid body seal and
spring damage. Leakage could result.
4
Body
Piston guide
Piston seal
and spring
Piston guide
Body
Piston seal
retainer
Body seal
and spring
Cap ring
Range spring
Cap assembly
Lower spring
button
Body
Seat retainer
Seat
Body
Piston guide
Piston
Handle
9. Invert the body and remove the poppet, the poppet
spring, and the poppet damper.
10. Remove the inlet filter from the inlet (marked ‘HP’) of the
body using the filter pick tool. Discard old lter.
NOTICE
Be careful not to scratch the sides of the inlet
port. Leakage could result.
Reassembly
NOTICE
Ensure all parts and tools are free of debris or
damage.
11. Insert the seat into the seat retainer with the groove
facing away from the seat retainer.
12. Place the poppet through the seat. Place the poppet
spring and the poppet damper onto the exposed end of
the poppet.
13. Invert the body and thread the seat assembly into the
body.
5
Poppet damper
Poppet
Poppet spring
Seat assembly
Body
Poppet damper
Seat
Poppet damper
Poppet spring
Poppet
Seat
Seat retainer
Groove
Filter pick tool
HP
Inlet
Discard
inlet filter.
14. Tighten the seat assembly to 13 lb·ft (17.5 N·m, 1.8 m·kg).
15. Insert the bottom of the piston seal insertion tool into
the piston guide. Insert the piston seal and spring into
the piston guide and use the top part of the piston seal
insertion tool to press the seal into place (17A). Then insert
the piston seal retainer, pressing it into place using the top
part of the piston seal insertion tool (17B).
Note: The open end of the piston seal and spring should
be facing up. The chamfer of the piston seal retainer
should be placed against the piston seal and spring.
16. Insert the bottom of the body seal insertion tool into the
body. Insert the body seal and spring and use the top part
of the body seal insertion tool to press the seal into place.
Note: The open end of the body seal and spring should be
facing down.
6
17. Push the piston into the piston guide.
18. Push the piston guide onto the body until it fully engages
with the body seal and spring.
19.
Insert the inlet filter in the inlet (marked ‘HP’) using the
filter insertion tool.
NOTICE
Do not insert the inlet filter with a sharp tool.
Damage to the filter could result.
20. Insert the lower spring button into the cap assembly with
the point towards the range spring if necessary.
Piston guide
Piston
Piston guide
Body
Body seal and spring
Piston
seal
insertion
tool
Open end up
Piston seal
and spring
17A
Chamfer facing
down
Piston seal
retainer
17B
Piston guide
Lower spring button
Range spring
Cap assembly
Open end down
Body seal
and spring
Body
Body seal
insertion tool
Body seal
insertion tool
Insertion tool
Inlet lter
HP
Inlet
7
21. Invert and thread the body into the cap assembly.
22. Tighten the cap ring to 100 ft·lb (135 N·m, 13.8 m·kg).
23. Test the regulator for proper operation.
24. If using an antitamper nut, thread the antitamper nut onto
the stem after the set outlet pressure is reached. Tighten
the nut to 13.0 ft·lb (17.5 N·m, 1.8 m·kg).
Cap ring
Cap assembly
Body
Piston
Swagelok — TM Swagelok Company
© 2010, 2014, 2015 Swagelok Company
October 2015, R2
MS-CRD-0138
For additional information, see www.swagelok.com.
Tabla de contenidos
Otros manuales de Controladores de Swagelok
Swagelok
Swagelok KFB Series Especificaciones técnicas
Swagelok
Swagelok RHPS Series Manual de usuario
Swagelok
Swagelok RDH10 Series Manual de usuario
Swagelok
Swagelok KLF Series Manual de usuario
Swagelok
Swagelok KHP Series Especificaciones técnicas
Swagelok
Swagelok LBS4 Manual de usuario
Swagelok
Swagelok KCB Series Especificaciones técnicas
Swagelok
Swagelok KCP Series Especificaciones técnicas
Swagelok
Swagelok RHPS Series Manual de usuario
Swagelok
Swagelok RS10 Series Manual de usuario
Swagelok
Swagelok RHPS Series Manual de usuario
Swagelok
Swagelok RHPS Series Manual de usuario
Swagelok
Swagelok KPB Series Especificaciones técnicas
Swagelok
Swagelok TBVS8 Manual de usuario
Swagelok
Swagelok BS2 series Manual de usuario
Swagelok
Swagelok KPR Series Especificaciones técnicas
Swagelok
Swagelok KPF Series Especificaciones técnicas
Swagelok
Swagelok PRS4 Manual de usuario
Swagelok
Swagelok RHPS Series Manual de usuario
Swagelok
Swagelok RS20 Manual de usuario
