Swagelok RHPS Series Manual de usuario

RHPS Series

VBS8

User Manual

Read the complete manual before installing and using the regulator.

WARNING

Before removing a regulator from the system for service, you must

▪depressurize system

▪purge the system to remove any residual system media left in the regulator.

Contents

Introduction ............................................................................................................................................... 3

Installation ................................................................................................................................................. 4

Operation ................................................................................................................................................... 5

Maintenance .............................................................................................................................................. 6

Testing ....................................................................................................................................................... 7

Troubleshooting ....................................................................................................................................... 8

Introduction

Representative drawing of the VBS8

1 body assembly 11 valve guiding ring 24 set screw

2 spring housing assembly 12 retaining ring 25 spring housing cover

3 ring 13 seal housing 27 ring

4 socket head screw 15 diaphragm plate 28 nut

5 body plug 16 O-ring 30 diaphragm

6 valve ring 17 O-ring 31 support diaphragm

7 valve O-ring 18 O-ring 34 nut

8 valve stem 19 O-ring 35 ring

9 valve seat 21 set spring 36 socket head cap screw

22 spring guide

Installation

WARNING

When installing a Swagelok®self-venting regulator, position the vent connection or line

away from operating personnel. Operating personnel must protect themselves from

exposure to system fluids.

CAUTION

Do not use the regulators as a shutoff device.

Connections to System

Before connecting to system, verify the regulator is closed by turning the set screw:

▪Counterclockwise, when viewed from above, until it stops for pressure reducing regulators,

▪Clockwise, when viewed from above, until it stops for back-pressure regulators.

mounting modes

The preferred mounting position of the regulator is vertical with the spring housing facing horizontal. (see

above sketch).

If grounding is required, connect a ground wire under a spring housing bolt.

Operation

Note: All handle directions are when viewed from above.

Outlet and control pressure settings are obtained by adjusting the set screw.

To increase the outlet or control pressure, rotate the set screw clockwise.

To decrease the outlet or control pressure, rotate the set screw counterclockwise and vent the

downstream side of the regulator.

Make the final setting in the direction of increasing pressure to obtain the most accurate set

points.

Once fluid is flowing through the system, fine tuning may be required.

Icing of the regulator at high flow rates or high pressure drops may occur if the gaseous media or

atmosphere contains moisture.

An auxiliary upstream filter is recommended for use in all but the cleanest of media.

Installation of a downstream pressure relief is recommended for regulator and system protection.

After flow, the inlet pressure will fall a little under the set pressure.

This is because of the closing force required for bubble-tight closing of the regulator.

This phenomenon is usually referred to as the “reseat pressure” and does not indicate a problem

with the regulator.

An increase in the flow will result in a rise of the set pressure.

A decrease in the flow will result in a fall of the set pressure.

This is because of the force required for opening the valve of the regulator.

This phenomenon is usually referred to as the “accumulation pressure” and does not indicate a

problem with the regulator.

An increase of the outlet pressure will result in a fall of the set pressure.

A decrease of the outlet pressure will result in a rise of the set pressure.

This phenomenon is usually referred to as the “dependency” and does not indicate a problem with

the regulator.

Maintenance

Required tools for maintenance

a vice to fasten the regulator

pincers to take out the O-rings

a torque wrench

a torque wrench hexagon head key 5 mm

socket wrenches 10 / 17 / 19 mm

open end wrench, 6 mm and 11/16 in.

snap ring pliers for retaining ring 38 mm

media and temperature compatible lubricant for reassembling threaded parts

media and temperature compatible lubricant for O-rings

Snoop®liquid leak detector

Disassembly

Loosen the socket head screws (12 pcs.# M6) and remove the spring housing and the set spring.

Loosen the nut on the valve stem and remove the diaphragm plates and diaphragm.

Remove the retaining ring, and take out the valve guiding ring and the valve assembly.

Loosen the body plug from the body and remove the body plug and seat.

Loosen the socket head screw from the valve assembly and remove the valve O-ring.

Inspection of disassembled parts

Check all parts for abnormal wear. Replace all parts in case of doubt.

Points of attention before assembly

All parts must be clean and undamaged before starting assembly.

Swagelok recommends replacing all O-rings and the diaphragm before assembly.

All threaded parts must be lightly lubricated before assembly, this to avoid galling of threads.

Assembly

Follow the points for disassembly in reverse order to assemble the regulator.

Recommended torques

CAUTION

Only tighten the bolts or parts if the regulator is completely depressurized.

Body plug 40 N·m (353 in.·lb)

Valve assembly socket head screw 10 N·m (88 in.·lb)

Nut on the diaphragm screw - M10 10 N·m (88 in.·lb)

Socket head cap screws - 16 pcs M06 10 N·m (88 in.·lb)

Spring housing cover 5 N·m (44 in.·lb)

Testing

Check the VBS8 for leakage across the seat, body plug and the diaphragm.

Check the required set pressure range and function.

A well performing regulator is 100% bubble tight.

Troubleshooting

Problem: Constant leakage from the outlet before the relief set pressure is reached.

Cause: A damaged valve and/or seat O-ring.

Solution: Replace the valve and/or seat O-ring

Problem: Constant leak through the hole at the side of the spring housing.

Cause: Damaged diaphragm or not enough torque on the nut on the diaphragm screw.

Solution: Replace the diaphragm or tighten the nut.

Problem: Leakage between the body and the spring housing.

Cause: A damaged diaphragm or insufficient torque on the bolts.

Solution: Check the torque on the bolts or replace the diaphragm.

Problem: The required set pressure can not be reached.

Cause: The inlet pressure is not high enough.

Solution: Make sure that the inlet pressure is sufficient.

Problem: The outlet pressure rises too much when flow increases.

Cause: There is too much flow passing through the regulator.

Solution: Check the specific application data with the flow tables in our product literature.

Note that the differential pressure over the seat is very low.

Problem: The regulator keeps venting in a tankblanketing application.

Cause: Thermal expansion of the blanket gas.

Solution: This is not a problem, the regulator functions well.

Problem: The regulator is placed in the system, and has different flow characteristics than printed in

the product literature.

Cause: Inside diameter of the piping or fittings are too small. Piping too long.

Solution: Install the regulator with proper piping and connections.

Consider the pressure drop caused by piping resistance.

Warranty Information

Swagelok products are backed by The Swagelok Limited Lifetime Warranty.

For a copy, visit swagelok.com or contact your authorized Swagelok representative.

For additional information, see www.swagelok.com. Swagelok, Snoop – Swagelok Company

February 2011, R0

MS-CRD-0169

Caution: Do not mix or interchange parts

with those of other manufacturers.

Otros manuales para RHPS Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Swagelok

Swagelok

Swagelok RDH10 Series Manual de usuario

Swagelok

Swagelok KCP Series Especificaciones técnicas

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok RA Series Manual de usuario

Swagelok

Swagelok RS2 Manual de usuario

Swagelok

Swagelok KFB Series Especificaciones técnicas

Swagelok

Swagelok BSH 10 Series Manual de usuario

Swagelok

Swagelok KLF Series Manual de usuario

Swagelok

Swagelok PRS15 Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok KHR Series Especificaciones técnicas

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok RS Series Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok KSV Series Especificaciones técnicas

Swagelok

Swagelok KHB Series Especificaciones técnicas

Swagelok

Swagelok KPB Series Especificaciones técnicas

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok LBS4 Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Swagelok

Swagelok RS20 Manual de usuario

Swagelok

Swagelok RHPS Series Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario