SurgeX SX-1115ip-X Manual de usuario

USER MANUAL

SurgeX

SX-1115ip-X

SX-1120ip-X

Web-Enabled Power Conditioning

Management System

Software Version: vQ110630G.123

Firmware Version: Q110630G.285

iControl Manual

INTRODUCTION......................................................................................................................... 3

INITIAL SET-UP.......................................................................................................................... 5

SETUP AND CONTROL UTILITY (SCU)............................................................................................. 5

COMMAND LINE INTERFACE (CLI) .................................................................................................. 6

SETTINGTHE IP ADDRESS............................................................................................................... 6

INSTALLATION.......................................................................................................................... 9

120 VOLT CONNECTIONS .................................................................................................................. 9

ETHERNET CONNECTION .................................................................................................................. 9

RS232 (SERIAL)PORT CONNECTION.................................................................................................. 9

DIAL LINE........................................................................................................................................ 9

EXPANSION ...................................................................................................................................... 9

LED INDICATORS.................................................................................................................... 10

WEB SERVER............................................................................................................................ 10

HEADER ......................................................................................................................................... 10

CONTROL....................................................................................................................................... 11

STATUS .......................................................................................................................................... 11

DEVICE VIEW................................................................................................................................. 11

OUTLET STATUS ............................................................................................................................ 12

GROUP VIEW.................................................................................................................................. 12

GLOBAL VIEW ............................................................................................................................... 12

AUTOPING VIEW............................................................................................................................ 13

COMMAND LINE INTERFACE (CLI) PROTOCOL.......................................................... 14

OUTLET COMMANDS...................................................................................................................... 14

USER COMMANDS.......................................................................................................................... 15

DEVICE COMMANDS ...................................................................................................................... 16

GROUP COMMANDS ....................................................................................................................... 18

NETWORK COMMANDS .................................................................................................................. 19

WEB SERVER COMMANDS ............................................................................................................. 19

TELNET COMMANDS ...................................................................................................................... 19

AUTOPING COMMANDS ................................................................................................................. 20

EVENT COMMANDS........................................................................................................................ 20

EMAIL COMMANDS ........................................................................................................................ 21

TIME COMMANDS .......................................................................................................................... 22

FIRMWARE UPLOAD COMMANDS................................................................................................... 22

iControl Manual

ADVANCED OPERATION ...................................................................................................... 23

DTMF CONTROL........................................................................................................................... 23

TIMED EVENTS............................................................................................................................... 24

AUTOPING ..................................................................................................................................... 25

SSLSECURITY............................................................................................................................... 26

CERTIFICATE UPLOAD UTILITY....................................................................................... 27

EMAIL NOTIFICATION.......................................................................................................... 28

SNMP........................................................................................................................................... 29

FIRMWARE UPGRADES ........................................................................................................ 29

FRONT PANEL RESET BUTTON.......................................................................................... 29

SETUP AND CONTROL UTILITY (SCU)............................................................................. 30

SNMP MIB .................................................................................................................................. 31

COMPLIANCE STATEMENTS .............................................................................................. 32

SPECIFICATIONS..................................................................................................................... 33

iControl Manual

INTRODUCTION

The SurgeX®iControl SX-1115ip-X (SX-1120ip-X) is a single rack-space, 120V, 15 (20) amp,

AC power conditioner that can be controlled over a network or the internet. The iControl

incorporates SurgeXAdvanced Series Mode®power conditioning and surge elimination, as well

as SurgeX Impedance Tolerant®EMI/RFI filtering. The simple web server structure allows basic

control of the outlets (and groups of outlets) and viewing of status information all from the home

page. The extensive programming and setup capabilities are accessed by a Setup and Control

Utility (SCU) or through a Command Line Interface (CLI).

Telnet and serial access use the same Command Line Interface (CLI) structure and syntax to

completely configure the iControl, or multiple iControls in a cluster configuration.

Up to 16 iControls can be linked together and controlled from a single web or CLI interface. One

master iControl provides the communication to the users and continuously receives status

information from the rest of the iControls in the cluster. Up to 128 outlets can be controlled in

this manner from one IP address.

Multiple outlets, across multiple iControls in clustered configurations, can be linked together in

named groups and managed together. This allows, for example, power cycling all devices of a

certain type together.

Up to 16 systems can be continuously monitored with AutoPing, with automatic power control

upon loss of contact. Reboot crashed systems, or provide auto power-up or –down for

environmental controls and notification systems.

Up to 16 users can be assigned administrator or user only rights, plus access to specific outlets

and groups. Users only see the outlets and groups they are assigned to.

The eight rear-mounted receptacles can each be individually controlled.

The metering includes the AC line voltage and total current draw.

Located on the rear panel are the input power cord, circuit breaker (15A or 20A), 8 NEMA 5-15

AC outlets, Serial connection (DCE, 9 pin D-subminiature), Network connection (RJ-45), Phone

connection (RJ-11), and Expansion Ports for cluster configurations.

iControl Manual

The two front panel LEDs provide indication of AC power (red) and surge protection status

(green). Also located on the front panel is a recessed Reset button (used to reset the

Administrator password).

The extensive programming capabilities of the iControl allow sequencing and scheduling to be

set up, not just for the host unit, but also for other iControl units on the same network.

The internal modem (for models with internal modem option) supports data calls from terminal

devices using the CLI, and direct dial from a tone telephone for simple On/Off control when

more sophisticated means are not available.

Setup and Control functions can be linked to any SNMP v1 compatible manager. The iControl

MIB is available at surgex.com.

All activity can be reported to a syslog compatible server.

The iControl’s internal web server is secured with Secure Sockets Layer (SSL) encryption.

The iControl’s Certificate Utility can be used to create, manage, and upload SSL certificates.

iControl Manual

INITIAL SET-UP

Setup and Control Utility (SCU)

The iControl Setup and Control Utility (SCU) utility provides the easiest means to find and

configure your iControl for use. The SCU can:

1. Automatically discover multiple iControls on a local network.

2. Add additional iControls not on the local network.

3. Download existing configurations from installed iControls.

4. Save existing configurations for later use or as backup.

5. Open saved configurations for change management.

6. Clone saved configurations for replication of similar configurations in multiple iControls.

7. Upload modified configurations to iControls.

8. Control outlets on one or more iControls throughout the network.

The iControl Setup and Control utility is available on the iControl CD or on the SurgeX website

at http://www.surgex.com

Note: The Setup and Control Utility only operates with iControls attached to the network.

iControls in a cluster configuration can be configured using the setup and control utility, if they

are attached to the network.

iControl Manual

Command Line Interface (CLI)

All configuration parameters are set using the Command Line Interface (CLI). The CLI is

accessed through the network, using a telnet client, or through the serial port, or data modem (for

models with internal modem option) using a terminal client. In iControl clusters, all remote

iControls can be configured and managed through the connection to the Master iControl. It is

also possible to access, configure and control any Expansion iControls directly.

Open a telnet client and point it to the current IP Address of the iControl.

(Factory Default is 192.168.0.254, telnet Port 23)

Connect to the Serial port or via PSTN connection to the modem.

(Factory Default is 115200,8,n,1)

Upon connection, press Enter, and then enter the username and password when prompted.

(Factory Default for username and password is admin)

Setting the IP Address

iControls come with factory default IP address 192.168.0.254.

There are three techniques to setting the IP address of the iControl:

1. Terminal Client software via Telnet, Serial, Modem.

2. Automatically from a DHCP Server

3. ARP / Ping (factory default)

To configure the mode to set the IP address, access the iControl’s command line interface (CLI)

and use the set ipmode command as indicated below.

iControl Manual

Setting the IP address using CLI

These are the basic commands to set the network parameters. After setting these parameters, the

iControl will need to be rebooted for the settings to take effect. Any command that requires

rebooting of the iControl will provide a prompt to do so. All commands may be entered as

required before rebooting.

Example: Telnet to default IP address 192.168.0.254 on Port 23.

iControl Rev Q101124G.272

User Name: admin

Password: *****

iControl > set ipaddress 192.168.1.3

Reboot Required!

iControl > set subnet 255.255.255.0

Reboot Required!

iControl > set gateway 192.168.1.7

Reboot Required!

iControl > reboot

IP Address = 192.168.1.3

Once the IP address is set, the following command can be used to prevent DHCP or ARP-Ping

from altering it: set ipmode static

Setting the IP address from a DHCP Server

A DHCP server will automatically assign an IP address (dynamic address) as well as Subnet

Mask and Gateway to the iControl.

To enable this feature, configure the iControl with the command set ipmode dhcp

Then reboot the iControl, or enter the command reboot

To find the IP address of the iControl, you will need to query your DHCP server and locate the

MAC address of the iControl in the DHCP server’s IP / MAC table. You can also access the CLI

and use the get network command, or use the Discover provision of the iControl Setup and

Control Utility (SCU).

iControl Manual

Setting the IP address using ARP / Ping

The ARP / Ping technique uses a PC running a command line (DOS Window) to set the IP

Address. To set the IP address using ARP, connect the iControl to your local network and apply

power. The IP address to be assigned to the iControl must use the same subnet as the computer

assigning the address. ARP does not work across routed or switched networks.

To set the IP address using ARP, the hardware (MAC) address must be known. This address is

located on the rear of the unit. The syntax for the MAC address is: nn-nn-nn-nn-nn-nn

Windows (98 and Later)

1. Access the iControl CLI and enter the set ipmode arp‐ping command.

2. On a PC, open a DOS window. (Run: Command)

3. Type the following command:

arp -s <IP Address> <MAC Address>

Where <IP Address> is the desired IP address (in dotted decimal) for the iControl and the

<MAC address> is the MAC Address of the iControl. The MAC Address of the iControl

is located on the rear of the unit.

Example: arp -s 63.211.86.165 00-50-c2-05-01-c1 <enter>

|new IP addr| |---MAC addr----|

4. Ping the iControl to program the IP address into the iControl.

Type: ping <IP Address>

Note: If the ping command returns “host not responding” 4 times then the address has

not been programmed properly. Check the IP or MAC Address for typographical errors.

Repeat step 2.

5. Delete the entry from the ARP cache by typing: arp -d <IP Address>

6. Ping the iControl to confirm that it has been programmed.

Note: If the iControl fails to respond, repeat steps 2-4 above.

Unix, Linux, MAC and others

Consult your systems administrator for information on how to set an IP Address. The unit should

be pinged after the IP Address has been set to confirm proper operation.

iControl Manual

INSTALLATION

The SurgeX iControl is designed to be installed in a 19 inch equipment rack and requires one

unit (1-U) of rack space. Use the four screws provided with the product to secure the rack ears to

the rack rails. These screws can be tightened by hand and do not require tools. Connect power to

the unit by plugging the cord into a 120V AC, 20 amp wall or floor receptacle. Do not plug the

unit into a relocatable power tap.

120 Volt Connections

The iControl has a total of 8 receptacles. Each receptacle is rated for a maximum load of 15

amps, but the total load of the SX-1115ip-X (SX-1120ip-X) must not exceed 15 (20) amps. Plug

the equipment cords into the receptacles as needed. The receptacles are numbered 1 through 8.

This same numbering is used in the control interface.

Ethernet Connection

The RJ45 connector for Ethernet is situated on the rear panel between the Serial and Modem

connectors. The default IP Address is 192.168.0.254.

RS232 (Serial) Port Connection

The iControl has a 9 pin D subminiature connector for RS-232 serial control. The connector is

configured as DCE for direct connection to a laptop or other terminal device. Default serial

parameters are 115,200 bps, 8 data, no parity, 1 stop bit (115200,8,n,1).

Serial Port Pinout

Pin Number

Description

Data Carrier Detect

Receive Data

Transmit Data

Data Terminal Ready

Signal Ground

Data Set Ready

Request To Send

Clear To Send

Ring Indicator

Dial Line

The internal modem (for models with internal modem option) supports both data and DTMF

control. The modem is approved for use in 36 countries. See Appendix for complete modem

certifications.

Expansion

The dual Expansion ports allow multiple iControls to be linked together and managed from a

single point. The expansion connector is a 6 wire RJ-11 modular jack. iControls can be

connected together in a daisy-chain or ring configuration. Up to 16 iControls can be clustered

together and managed from a single web page or console session. Use 6 conductor data cable to

connect iControls for cluster configurations. Configuration settings determine whether the

iControl is the Master or Expansion.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Protector contra sobretensiones de SurgeX

SurgeX

SurgeX Defender Series Manual de usuario

SurgeX

SurgeX SX1115RT Manual de usuario

SurgeX

SurgeX SX-DS-154 DEFENDER SERIES MULTIPAK Manual de usuario

SurgeX

SurgeX Axess-Ready SA-82-AR/XF2-AR Manual de usuario

SurgeX

SurgeX Defender Series Manual de usuario

SurgeX

SurgeX XQ515 Manual de usuario

Manuales populares de Protector contra sobretensiones de otras marcas

ELAC

ELAC ProteK PR91-W Manual de usuario

Tsubaki

Tsubaki TSM4000M1 Manual de usuario

QVS

QVS PP134C Manual de usuario

CyberPower

CyberPower CSP604T Manual de usuario

Davis Instruments

Davis Instruments Radio Surge Protector Manual de usuario

M-system

M-system MGA-100 Manual de usuario

CyberPower

CyberPower CSP706T Manual de usuario

CyberPower

CyberPower B300WRC1 Manual de usuario

M-system

M-system MGD-24 Manual de usuario

Leviton

Leviton 51120-3R Manual de usuario

Panamax

Panamax MAX 5400-EX Manual de usuario

CyberPower

CyberPower B1006T Manual de usuario

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Manual de usuario

Minuteman

Minuteman MMS7120RCT Manual de usuario

Leviton

Leviton 52412-DS3 Manual de usuario

Savio

Savio LZ-07 Manual de usuario

Siemens

Siemens HNM3M120 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Manual de usuario