Supermicro H13SAE-MF Manual de usuario

H13SAE-MF

ENGLISH

QUICK REFERENCE GUIDE

Revision 1.0

H13SAE-MF QUICK REFERENCE GUIDE

Standardized Warning Statements

Motherboards

About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user of situations where bodily injury

might occur. Should you have questions or experience di󰀩culty, contact Supermicro's Technical Support Department

for assistance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the Supermicro chassis.

WARNING: This product can expose you to chemicals including

lead, known to the State of California to cause cancer and birth

defects or other reproductive harm. For more information, go

to www.P65Warnings.ca.gov.

Battery Handling

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-

lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理

廢棄舊電池。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理

废旧电池。

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメーカーが推奨する型、または同等のもの

を使用下さい。使用済電池は製造元の指示に従って処分して下さい。

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한

종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.









Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.

Product Safety Information

H13SAE-MF QUICK REFERENCE GUIDE 限用物質含有情況標示聲明書

限

用

物

質

含

有

情

況

標

示

聲

明

書

設備名稱：主機板 / Motherboard



型號（型式）：H13SAE‐MF

單元

Ｕnit

限用物質及其化學符號

鉛

Lead

(Pb) 汞

Mercury

(Hg) 鎘

Cadmium

(Cd)

六價鉻

Hexavalent

chromium

(Cr

)

多溴聯苯

Polybrominated

biphenyls

(PBB)

多溴二苯醚

Polybrominated

diphenyl ethers

(PBDE)

電路板組件

(PCBA)

－○○○○○

連接器

(Connector) －○○○○○

備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準

值。

備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。

備考3.〝－〞係指該項限用物質為排除項目。

Equipment name

Type designation (Type)

Restricted substances and its chemical symbols

Declaration of the Presence Condition of the Restricted Substances Marking

Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the

reference percentage value of presence condition.

Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.

Note 3：The “−” indicates that the restricted substance corresponds to the exemption.

H13SAE-MF

Quick RefeRence Guide Rev. 1.0

SUPERMICR R

Motherboard Layout and Features

=mounting hole

I/O BACK PANEL

H13SAE-MF

MAC CODE

REV:1.00

DESIGNED IN USA

BIOS LICENSE

BAR CODE

IPMI CODE

C A

1 2 3

JF1

SATA3

SATA2 SATA1

USB8/9(3.0)

USB2(3.1)

USB3(3.1)

USB4(3.1)

USB5(3.1)

USB7(3.2)

UID-SW

UID-LED

AUDIO FP

JSD1

USB 0/1

FANA

FAN5

FAN3 FAN2 FAN1

DP/HDMI

SATA0

CPU

FAN4

JPW2

HD AUDIO

LAN2

M.2-C1

CPU SLOT6 PCIe 5.0 X16

COM1

VGA

IPMI

USB6(3.1)

LAN1

BMC_LAN

PCH SLOT7 PCIe 4.0 X4

CPU SLOT4 PCIe 5.0 X8 (IN X16)

JSTBY1:

1-2:ENABLE

JPG1:VGA

2-3:DISABLE

JWD1:WATCH DOG

1-2:RST

2-3:NMI

TPM/PORT80

M.2-C2

CHASSIS INTRUSION

COM2

5V STBY

JPW1

DIMMA2

DIMMA1

DIMMB1

DIMMB2

JF1

JPI2C1

JBT1

FANB

J4901

JPG1

JWD1

JSTBY1

IPMI

LEDM22

LEDM1

JUBUD1

UID SW

UID_LED

PCIe 4.0x4

Package contents

• One Supermicro Motherboard

• Four SATA Cables

• One I/O Shield

• One Quick Reference Guide

Jumpers

Jumper Description Default

JBT1 Clear CMOS (Onboard) Short Pads to Clear CMOS

UID SW Unit ID Switch (Push-Button Toggle Switch ON/OFF) O󰀨

JPG1 VGA Enable Pins 1-2 (Enabled)

JWD1 Watch Dog Control Pins 1-2 (Reset)

JUBUD1 BIOS Update O󰀨

Connectors

Connector Description

JL1 Chassis Intrusion Header

SATA0-1, SATA2-3 Dual SATA Port Connectors Supporting up to Four Devices

J4901 Front Panel HD Audio Header

JPW2 12V 8-pin CPU Core Power Supply Connector (Required)

JPW1 24-pin ATX Main Power Connector (Required)

JF1 Front Control Panel Header

BT1 Onboard Battery

M.2-C1/M.2-C2 M.2 PCIe Interfaces

JSTBY1 Inject External P5V_STBY Power

JIPMB1 4-pin BMC External I2C Header (For an IPMI-Supported Card)

DIMMA1~DIMMB2 DIMM Slots

FAN1~FAN5 CPU Fans

FANA~FANB System Cooling Fans

BMC LAN BMC LAN Port

JTPM1 TPM (Trusted Platform Module)/Port 80

JPI2C1 Power System Management Bus (SMB) I2C Header

COM1/COM2 Serial Port/Header

VGA Rear Panel VGA Port

USB0/1 USB 2.0 Ports

USB2/4 Rear USB 3.2 Gen1 Alt Ports

USB3/5/7 Rear USB 3.2 Gen2 Ports

USB6 USB 3.2 Gen2x2 Port

USB8/9 Front USB3.2 Gen1 Ports

LED Indicators

LED Description Color/State

LED1 Unit Identier (UID) LED Blue: UID Identied

LED4 Onboard Power LED Solid Green: Power On

LEDM1 BMC Heartbeat LED Green: Blinking (BMC Normal)

LEDM21~LEDM22 M.2 SSD LED Blinking: Device Working

Jumpers and Connectors

LED Indicators

ContaCt InformatIon

• www.supermicro.com (Email: [email protected])

• Manuals: http://www.supermicro.com/support/manuals

• Drivers & Utilities: https://www.supermicro.com/wdl/

• Safety: http://www.supermicro.com/about/policies/safety_information.cfm

DIMM Population Guide

Type Channel

A1 A2 B1 B2

1 DIMM V

2 DIMMs V V

4 DIMMs V V V V

CPU

DIMMB1

DIMMB2

DIMMA1

DIMMA2

Memory Population Guidelines

There is no specic order or sequence required when installing memory modules. However do keep the following

in mind:

• The motherboard will support one, two or four modules. However, to achieve the best memory performance,

fully populate the motherboard with validated memory modules.

UID LED-

NIC1 Link LED-

Key, no pinKey, no pin

HDD LED-

PWR_LED-

Ground

19 20

Power Fail LED+

Reset Switch

Power Fail LED-

NIC2 Link LED-

UID LED+

NIC1 Link LED+

HDD LED+/UID Switch+

PWR LED+

NMI Switch

NIC2 Link LED+

Power Switch

Front Control Panel (JF1)

DIMM Memory Installation

CPU & Memory Support

The H13SAE-MF motherboard supports up to 128 GB of ECC/Non ECC UDIMM DDR5 5200 MT/s speed, populated

in four DIMM slots. Refer to the table below for additional memory information.

Notes:

• Always use DDR5 DIMM modules of the same type, size and speed.

• For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest

memory updates, please refer to our website at http://www.supermicro.com/products/motherboard.

• Please be aware that removing a DDR5 DIMM module at a slant angle may cause damages. It is recommend

that you lift the module straight up out of the slot.

• The DDR5 DIMM module is NOT hot-swappable and be sure to disconnect power for a minimum of twenty

seconds before inserting or removing it.

MNL-2627-QRG-100

written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is

not guaranteed.

Notes

• Graphics shown in this quick reference guide are for illustration purposes only. Your compo-

nents may or may not look exactly the same as the drawings shown in this guide.

• Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, LED

indicators, memory support and CPU/motherboard installation instructions.

Installing the Processor

Note: Do not remove the plastic cover covering the outside of the

socket. This cover will pop out during installation of the processor.

1. Use a nger to push down the lever, then move the lever

rightward. Pull the lever until it passes over the processor

socket.

2. Pick up the processor on its left and right edges. Hold the

processor over the socket and align the arrow on the top-left

corner of the processor with the arrow on the top-left corner

of the socket. Gently lower it onto the AM5 socket pins.

3. With the processor in the socket, lower the socket force

frame.

4. Reattach the lever arm onto the right side of the socket. The

outer plastic cover will pop out when the lever arm is reat-

tached.

Note: Store the outer plastic cover. Attach the outer plastic cover to

the socket force frame when storing or transporting the motherboard

without a processor.

5. When nished, the socket force frame will secure the proces-

sor.

Load Lever

Socket Force Frame

Lever Lock

Outer Plastic Cover

CPU Installation

Rear I/O Ports

#Description #Description #Description

1Center/LFE Out 8VGA Port 15 USB 3.2 Gen2 Type A (10 Gb)

2Surround Out 9DisplayPort 1.4a 16 USB 3.2 Gen2 Alt Mode*

3S/PDIF Out 10 HDMI 2.0 Port 17 Dedicated IPMI LAN Port (1 Gb)

4Line In 11 1 Gb RJ45 Port 18 USB 3.2 Gen2 Type A (10 Gb)

5Line Out 12 USB 3.2 Gen2 Type A (10 Gb) 19 USB 3.2 Gen2x2 (20 Gb)

6Mic In 13 USB 3.2 Gen2 Alt Mode* 20 UID

7COM Port 14 1 Gb RJ45 Port 21 JUBUD1

*Video out only supports one output at the same time, and it must use Type C to DP (standard) cable.

20 21

13 16 19

14 17

15 18

Back Panel I/O Connectors

Pin 1

Processor

Notch

Socket Processor Notch

Processor Arrow

Socket Arrow

H13SAE-MF QUICK REFERENCE GUIDE

NOTES

Otros manuales para H13SAE-MF

Tabla de contenidos

Otros manuales de Hardware de computadora de Supermicro

Supermicro

Supermicro AOC-A25G-i2SM Manual de usuario

Supermicro

Supermicro B2SS2-F Manual de usuario

Supermicro

Supermicro BPN-SAS3-836EL Manual de usuario

Supermicro

Supermicro AOC-A100G-b2CM Manual de usuario

Supermicro

Supermicro SuperServer 5019S-L Manual de usuario

Supermicro

Supermicro AOC-A100G-m2CM Manual de usuario

Supermicro

Supermicro X11SDC-4C Manual de usuario

Supermicro

Supermicro X12SDV-4C-SP6F Manual de usuario

Supermicro

Supermicro BPN-SAS3-116A-N10 Manual de usuario

Supermicro

Supermicro AOC-SIMLP-B Manual de usuario

Supermicro

Supermicro AOC-R1UG-IBQ Manual de usuario

Supermicro

Supermicro H13SSH Manual de usuario

Supermicro

Supermicro X12DPG-AR Manual de usuario

Supermicro

Supermicro SuperServer SYS-510T-M Manual de usuario

Supermicro

Supermicro BPN-SAS2-826EL Series Manual de usuario

Supermicro

Supermicro AOC-SLG4-4E4T Manual de usuario

Supermicro

Supermicro X12SPA-TF Manual de usuario

Supermicro

Supermicro AOC-SGP-i2 Manual de usuario

Supermicro

Supermicro A3SEV-2C-LN4 Manual de usuario

Supermicro

Supermicro AOC-MTGN-i2S Manual de usuario

Supermicro

Supermicro B13SEG Manual de usuario

Supermicro

Supermicro BPN-SAS-825MTQ Backplane Manual de usuario

Supermicro

Supermicro B3SD1-20C-25G Manual de usuario

Supermicro

Supermicro AOC-S3816L-L16iT Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario