Supermicro M12SWA-TF Manual de usuario

M12SWA-TF

ENGLISH

繁體中文

简体中文

日本語

(

한국어

QUICK REFERENCE GUIDE

Revision 1.0b

M12SWA-TF QUICK REFERENCE GUIDE

Standardized Warning Statements

Motherboards

About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user of situations where bodily injury

might occur. Should you have questions or experience di󰀩culty, contact Supermicro's Technical Support Department

for assistance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the Supermicro chassis.

WARNING: This product can expose you to chemicals including

lead, known to the State of California to cause cancer and birth

defects or other reproductive harm. For more information, go

to www.P65Warnings.ca.gov.

Battery Handling

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-

lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理

廢棄舊電池。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理

废旧电池。

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメーカーが推奨する型、または同等のもの

を使用下さい。使用済電池は製造元の指示に従って処分して下さい。

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한

종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.









Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.

Product Safety Information

M12SWA-TF QUICK REFERENCE GUIDE 限用物質含有情況標示聲明書

限

用

物

質

含

有

情

況

標

示

聲

明

書

設備名稱：主機板 /

Motherboard

型號（型式）：M12SWA-TF

單元Ｕnit

限用物質及其化學符號

鉛Lead

(Pb) 汞Mercury

(Hg) 鎘Cadmium

(Cd)

六價鉻

Hexavalent

chromium

(Cr+6)

多溴聯苯

Polybrominated

biphenyls

(PBB)

多溴二苯醚

Polybrominated

diphenyl ethers

(PBDE)

主機板

(Motherboard)

－○○○○○

備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準

值。

備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。

備考3.〝－〞係指該項限用物質為排除項目。

Equipment name

Type designation (Type)

Restricted substances and its chemical symbols

Declaration of the Presence Condition of the Restricted Substances Marking

Note 1

：

“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the

reference percentage value of presence condition.

Note 2

：

“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.

Note 3

：

The “−” indicates that the restricted substance corresponds to the exemption.

M12SWA-TF QUICK REFERENCE GUIDE

NOTES

M12SWA-TF

Quick RefeRence Guide Rev. 1.0a

SUPERMICR R

BAR CODE

M12SWA-TF

REV:1.00

DESIGNED IN USA

BIOS LICENSE

IPMI CODE

MAC CODE

SAS CODE

DIMME1~H1

FAN5

SATA0

JPW1

JTPM1

VGA

JWP1

JSPDIF_OUT

JPAC1

UID LED

J31

BMC LED

CPU SLOT1 PCIe 4.0 X16

CPU SLOT2 PCIe 4.0 X16

CPU SLOT3 PCIe 4.0 X16

CPU SLOT5 PCIe 4.0 X16

CPU SLOT6 PCIe 4.0 X16

CPU SLOT7 PCIe 4.0 X16

FANC

FAN6

FAND

CPU

DIMMA1~D1

JPW4

FAN4

FAN3

JWD1

FANB

FANA

JSTBY1

FAN1

FAN2

BT1

SATA1

JL1

COM2

JWP2

JSD1

COM1

JUSBLAN1

JPW2

M.2-0LED

M.2-1LED

M.2-2LED

M.2-3LED

JBT1

JF1

JPI2C1: PWR I2C

JOH1

USB 2/3

Motherboard Layout and Features

=mounting hole

I/O BACK PANEL

PCH_FAN

JAUDIO1

USB 6/7

USB 8/12

LAN 1

JPW3

JP5

JPL1

12V PUMP PWR1

JD1

SATA2

SATA3

USB 10/11

USB 9

USB 0/1

M.2 NVME

USB 4/5

U.2

JPL2

JPUSB1

LAN 2

Package contents

• One Supermicro Motherboard

• Four SATA Cables

• One I/O Shield

• One Quick Reference Guide

• One GPU to CPU Power Cable

• M.2 Screw and Stand Kit

Connector Description

JD1 Front Panel External Speaker

J31 Front Panel Audio FP Header

BT1 Onboard Battery

COM1 COM1: COM Port (Back Panel)

CPU SLOT1~7 PCIe 4.0 x16 Slots

FAN1 ~ FAN6 CPU Fan Headers

FANA ~ FAND System Fan Headers

12V_PUMP_PWR1 12V 4-pin power connector for liquid cooling CPU pump

SATA0~3 Serial ATA (SATA 3.0) Ports (6Gb/second)

JSD1 SATA DOM Power Connector

JF1 Front Control Panel Header

JL1 Chassis Intrusion Header

JOH1 Overheat LED Header

JPI2C1 Power Supply SMBus I2C Header

JPW1 24-pin ATX Main Power Connector (Required)

JPW2~JPW4 +12V 8-pin CPU Power Connectors (Required)

JSTBY1 Standby Power Header (5V)

JTPM1 Trusted Platform Module (TPM)/Port 80 Header

JSPDIF Out SPDIF (Sony/Philips Digital Interface) Out Headers

USB0/1 USB 2.0 Front Panel Header

USB10/11 USB 3.2 (Gen. 1) Type A Front Panel Header

USB9 USB 3.2 (Gen. 2) Type C Front Panel Header

VGA VGA Port

Jumpers and Connectors

Jumpers

Jumper Description Default

JBT1 Clear CMOS (Onboard) Short Pads to Clear CMOS

JPAC1 HD Audio Enable/Disable Pins 1-2 (Enabled)

JPL1, JPL2 LAN1/LAN2 Enable/Disable Pins 1-2 (Enabled)

JPUSB1 USB6/7 Wake Up Pins 1-2 (Enabled)

JWD1 Watch Dog Time Control Pins 1-2 (Reset)

JP5 USB 12 Enable/Disable Pins 1-2 (Enabled)

Connectors

LED Description Color/State

M.2-0LED, M.2-1LED,

M.2-2LED, M.2-3LED M.2 LEDs for M.2-4/M.2-3/M.2-2/M.2-1 Blinking Green: Device Working

BMC LED BMC Heartbeat LED Blinking Green: BMC Normal

Power LED Onboard Power LED Solid Green: Power On

UID-LED Unit Identier (UID) LED Blue On: Unit Identied

LED Indicators

Notes:

• It is recommended that you connect both 8-pin (JPW3) and 24-pin (JPW1) connectors to your power supply modules

before powering on the motherboard.

• For installing multiple GPU cards, both 8-pin connectors (JPW2 and JPW4) must be connected.

ContaCt InformatIon

• www.supermicro.com (Email: [email protected])

• Manuals: http://www.supermicro.com/support/manuals

• Drivers & Utilities: https://www.supermicro.com/wdl/

• Safety: http://www.supermicro.com/about/policies/safety_information.cfm

The M12SWA-TF motherboard supports AMD Ryzen™ Threadripper™ PRO 3000 Series Processors, with up to 64 cores. Memory supports up

to 8 DDDR4 ECC and non-ECC, buffered and unbuffered, UDIMM, RDIMM, and 3DS RDIMM sockets, with speeds of up to 3200MHz (1DPC).

Max capacity is up to 256GB (UDIMM) or 2TB (RDIMM) in 8 DDR4 DIMM slots. Populating these DIMM slots with a pair of memory modules

of the same type and size will result in interleaved memory, which will improve memory performance.

Notes:1) For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest memory updates,

please refer to our website at http://www.supermicro.com/products/motherboard.

2) Always connect the power cord last, and always remove it before adding, removing, or changing any hardware components.

3) Always connect the power cord to both 24-pin (JPW1) and 8-pin (JPW3) connectors before powering on the motherboard.

4) For installting multiple GPU cards, both 8-pin connectors (JPW2 and JPW4) must be connected.

CPU & Memory Support

Front Control Panel (JF1)

Power Button

UID LED

NIC1 Active LED

Reset Button

HDD LED

PWR LED

Reset

PWR

P3V3_STBY_UID SW

P3V3_STBY

Ground

P3V3_STBY

1 2

Ground

Power Fail LED

NIC2 Active LED

SW_NMI_N

P3V3

OH/Fan Fail LED

P3V3

Memory Population

Guidelines

• For optimal performance, it is recom-

mended that DDR4 DIMM modules of

the same size, type, and speed should

be installed.

• Mixed DIMM speeds can be installed.

However, all DIMMs will run at the speed

of the slowest DIMM.

• When installing memory modules, the

DIMM slots should be populated in the

following order: DIMMC1, DIMMD1,

DIMMG1, DIMMH1, DIMMA1, DIMME1,

DIMMB1, DIMMF1.

CPU

DIMMA1

DIMMB1

DIMMC1

DIMMD1

DIMMH1

DIMMG1

DIMMF1

DIMME1

DIMM Memory Installation

DIMM Population Guide

CPU# Channel

D1 C1 B1 A1 E1 F1 G1 H1

1 DIMM

CPU1 V

2 DIMMs

CPU1 V V

4 DIMMs

CPU1 V V V V

6 DIMMs

CPU1 V V V V V V

8 DIMMs

CPU1 V V V V V V V V

MNL-2336-QRG-100

written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is

not guaranteed.

Notes

• Graphics shown in this quick reference guide are for illustration purposes only. Your compo-

nents may or may not look exactly the same as the drawings shown in this guide.

• Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, LED

indicators, memory support and CPU/motherboard installation instructions.

Screw #3

CPU Installation

Back Panel I/O Connectors

PHM Installation

1Lower the heatsink down till it rests

securely over the four screw holes on the

socket frame of the CPU Package.

Screw #1

Screw #2

Screw #3

Carrier Frame/

CPU Package

External Cap

1Unscrew the screws

holding down Force Frame

in the sequence of 3-2-1.

2Remove the External Cap. 1

3Slide the Carrier Frame/

CPU Package downwards to the

bottom.

2As illustrated, tighten the four

screws down on the heatsink in a

diagonal pattern till it is secured.

Screw #1

Screw #2

Screw #4

A. COM1 F. USB6: USB3.2 Gen2

(Type A, 10Gb/s)

K. USB 2: USB3.2 Gen2

(Type A, 10Gb/s) P. Line In

B. VGA Port G. USB7: USB3.2 Gen2

(Type A, 10Gb)

L. USB 3: USB3.2 Gen2

(Type A, 10Gb/s) Q. Line Out

C. 1Gb LAN Port (i210) H. 10Gb LAN Port (AQC113C) M. Center/LFE Out R. Mic In

D. USB12: USB3.2 Gen1

(Type A, 5Gb/s)

I. USB 4: USB3.2 Gen1

(Type A, 5Gb/s) N. Surround Out S. UID Switch

E. USB8: USB3.2 Gen2x2

(Type C, 20Gb/s)

J. USB5: USB3.2 Gen1

(Type A, 5Gb/s) O. S/PDIF Out

M12SWA-TF

美超微電腦股份有限公司

X12SWA-TF

快速參考指南版本

1.0a

SUPERMICR R

BAR CODE

M12SWA-TF

REV:1.00

DESIGNED IN USA

BIOS LICENSE

IPMI CODE

MAC CODE

SAS CODE

DIMME1~H1

FAN5

SATA0

JPW1

JTPM1

VGA

JWP1

JSPDIF_OUT

JPAC1

UID LED

J31

BMC LED

CPU SLOT1 PCIe 4.0 X16

CPU SLOT2 PCIe 4.0 X16

CPU SLOT3 PCIe 4.0 X16

CPU SLOT5 PCIe 4.0 X16

CPU SLOT6 PCIe 4.0 X16

CPU SLOT7 PCIe 4.0 X16

FANC

FAN6

FAND

CPU

DIMMA1~D1

JPW4

FAN4

FAN3

JWD1

FANB

FANA

JSTBY1

FAN1

FAN2

BT1

SATA1

JL1

COM2

JWP2

JSD1

COM1

JUSBLAN1

JPW2

M.2-0LED

M.2-1LED

M.2-2LED

M.2-3LED

JBT1

JF1

JPI2C1: PWR I2C

JOH1

USB 2/3

主機板元件配置圖

= 裝機孔

I/O 後擋板

PCH_FAN

JAUDIO1

USB 6/7

USB 8/12

LAN 1

JPW3

JP5

JPL1

12V PUMP PWR1

JD1

SATA2

SATA3

USB 10/11

USB 9

USB 0/1

M.2 NVME

USB 4/5

U.2

JPL2

JPUSB1

LAN 2

Otros manuales para M12SWA-TF

Tabla de contenidos

Idiomas:

Otros manuales de Hardware de computadora de Supermicro

Supermicro

Supermicro X11SDC-4C Manual de usuario

Supermicro

Supermicro SuperBlade SBI-420P-4T2N Manual de usuario

Supermicro

Supermicro B2SS1-CPU Manual de usuario

Supermicro

Supermicro AOC-SLG3-4E4T Manual de usuario

Supermicro

Supermicro AOC-S25G6-M2S Manual de usuario

Supermicro

Supermicro AOC-SIMSO Manual de usuario

Supermicro

Supermicro H13SSW Manual de usuario

Supermicro

Supermicro SBI-7127RG Manual de usuario

Supermicro

Supermicro BPN-SAS3-833A Manual de usuario

Supermicro

Supermicro AOC-A100G-m2CM Manual de usuario

Supermicro

Supermicro AOC-A25G-i2SM Manual de usuario

Supermicro

Supermicro AOC-UIBQ-m1 Manual de usuario

Supermicro

Supermicro AOM-S3108-H8 Manual de usuario

Supermicro

Supermicro SuperWorkstation SYS-551A-T Manual de usuario

Supermicro

Supermicro SuperBlade SBA-4114S-C2N Manual de usuario

Supermicro

Supermicro SAS-836A Manual de usuario

Supermicro

Supermicro A+ Server AS -3015A-I Manual de usuario

Supermicro

Supermicro SuperServer SYS-E300-12D-4CN6P Manual de usuario

Supermicro

Supermicro BPN-SAS3-743A Manual de usuario

Supermicro

Supermicro AOC-A25G-m2SM Manual de usuario

Supermicro

Supermicro AOC-SLG2-2TM2 Manual de usuario

Supermicro

Supermicro AOC-SLG4-2H8M2 Manual de usuario

Supermicro

Supermicro AOC-SMG3-2H8M2 Manual de usuario

Supermicro

Supermicro SBI-7127R-S6 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario