Sungrow SH5K Manual de usuario
Sungrow Australia Group Pty. Ltd. | 1800 SUNGROW (786 476)
service@sungrowpower.com.au | www.sungrowpower.com.au
TD_201808_Hybrid_Wiring Guide for LG Battery with SH5K & SH5K+_V1.0 Page 1 of 5
© Sungrow Australia Group Pty. Ltd. All rights reserved.
The information in this document is subject to change without notice.
Wiring Guide for LG battery with SH5K / SH5K+
This document describes the wiring and setup procedure for a single LG battery pack.
Refer to manufacturer’s documents for multiple parallel connections.
1Cable Wiring Procedure
1.1 LG Generation II and SH5K
The LG Generation II battery communicates with the Sungrow SH5K V11 inverter via
an Ethernet cable. Prepare the following materials and tools before wiring.
•Ethernet cables,
•RJ45 Crimpable plugs, and
•an RJ45 Crimping tool.
Step 1 Use the crimping tool to cut into
the Ethernet cable plastic sheath about 1
inch (2.5 cm) from the end of the cut cable
(Figure 1).
Figure 1 Cut cable end and leave 1 inch
Step 2 Pinch the wires between your
fingers and straighten them out. Carefully
push all 8 unstripped coloured wires into
the RJ45 plug as shown for T568B and
T568A (Figure 2).
T568B
RJ45 plug
1----8
Corresponding Relationship Between Cables and Pins:
T568A
Figure 2 Colour cable order for the Ethernet
cable
Sungrow Australia Group Pty. Ltd. | 1800 SUNGROW (786 476)
service@sungrowpower.com.au | www.sungrowpower.com.au
TD_201808_Hybrid_Wiring Guide for LG Battery with SH5K & SH5K+_V1.0 Page 2 of 5
© Sungrow Australia Group Pty. Ltd. All rights reserved.
The information in this document is subject to change without notice.
Step 3 Insert the RJ45 plug into the battery
port until it makes a clicking sound (Figure 3).
Figure 3 Insert RJ45 plug into battery port
Step 4 Insert the RJ45 plug into the BAT_Com.
port (Figure 4) on the configuration circuit
board until it makes a clicking sound
Figure 4 BAT_Com. port in the inverter
1.2 LG Generation II and SH5K+
The LG Generation II battery communicates with the Sungrow SH5K+ inverter via an
Ethernet cable (CAN wire).
The CAN wire is included in the delivery, as
shown in Figure 5.
CANH: Blue and Green
CANL: Blue-white and Green-white
Figure 5 CAN wire in the delivery
Sungrow Australia Group Pty. Ltd. | 1800 SUNGROW (786 476)
service@sungrowpower.com.au | www.sungrowpower.com.au
TD_201808_Hybrid_Wiring Guide for LG Battery with SH5K & SH5K+_V1.0 Page 3 of 5
© Sungrow Australia Group Pty. Ltd. All rights reserved.
The information in this document is subject to change without notice.
Step 1 Insert the RJ45 plug into the battery
port until it makes a clicking sound (Figure 6).
Figure 6 Insert RJ45 plug into battery port
Step 2 Plug CANH into the CANH port and plug
CANL into the CANL port of the configuration circuit
board of SH5K+ (Figure 7).
Figure 7 Insert CANH and CANL pins to
SH5K+ circuit board
2Setting for communication interface
Remove the switch cover by pulling it up to expose the circuit board.
This SW select DIP switch is initially set to
0000 (Figure 8).
DIP
3 4
Figure 8 Initial Setting
Sungrow Australia Group Pty. Ltd. | 1800 SUNGROW (786 476)
service@sungrowpower.com.au | www.sungrowpower.com.au
TD_201808_Hybrid_Wiring Guide for LG Battery with SH5K & SH5K+_V1.0 Page 4 of 5
© Sungrow Australia Group Pty. Ltd. All rights reserved.
The information in this document is subject to change without notice.
When there is only one battery pack, the
battery pack is directly connected to the
inverter, the SW select DIP switch should be
set to 0011 (Figure 9).
Refer to manufacturer’s documents for two
battery packs.
DIP
3 4
Figure 9 Setting for one battery pack
3Inverter Settings
Select the correct battery model and the capacity composition (Figure 10).
For SH5K V11 LCD:
Main Screen (Press ENTER) →Menu (Press × 2) →Settings (Press ENTER) →Input
password 111 (Press ENTER) →Settings (Press × 5) →Battery Type (Press ENTER)
For SH5K+ LCD:
Main Screen (Press ENT) →Menu (Press × 2) →Settings (Press ENT) →Input password
111 (Press ENT) →Settings (Press × 8) →Battery Type (Press ENT)
Li-ion LG
Li-ion Samsung
No Battery
Battery Type
Li-ion LG
1/3
LG Generation I
LG Generation II
Li-ion Generation II
3.3 kWh
9.8 kWh
6.5 kWh
13.0 kWh
16.3 kWh 19.6 kWh
Figure 10 Setting battery type and capacity
Note:
Watch the SH5K home screen. If you see '--', the
communication is not correctly connected (Figure
11).
5000
Running
=
~
--
500
3000
16:37
(W)
+-
Figure 11 Inverter Home Screen
Sungrow Australia Group Pty. Ltd. | 1800 SUNGROW (786 476)
service@sungrowpower.com.au | www.sungrowpower.com.au
TD_201808_Hybrid_Wiring Guide for LG Battery with SH5K & SH5K+_V1.0 Page 5 of 5
© Sungrow Australia Group Pty. Ltd. All rights reserved.
The information in this document is subject to change without notice.
Remove the switch cover on the battery by pulling it up to expose the circuit board.
Check the settings.
Dip switches (①, ②, ⑥) settings:
SW1 (SW Protocol)
SW2 (Cell Type)
SW6 (Terminal Resistor)
One battery pack: 0011
DIP
3 4
00
11
Rotatory switch (③, ④, ⑤) settings:
SW3 (CAN_H)
SW4 (CAN_L)
SW5 (GND)
4:
5:
2:
Otros manuales para SH5K
7
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Inversor de Sungrow
Sungrow
Sungrow SG60KTL Manual de usuario
Sungrow
Sungrow SG2KTL-S Manual de usuario
Sungrow
Sungrow SG30CX Manual de usuario
Sungrow
Sungrow SH6.0RT Guía de instalación
Sungrow
Sungrow SG110CX Manual de usuario
Sungrow
Sungrow SH8.0RT Manual de usuario
Sungrow
Sungrow SH5K Manual del propietario
Sungrow
Sungrow SP600S Manual de usuario
Sungrow
Sungrow SG3KTL-M Manual de usuario
Sungrow
Sungrow SG3125HV-20 Guía del usuario
Sungrow
Sungrow SG125HV Manual de usuario
Sungrow
Sungrow SG15KTL-M Manual de usuario
Sungrow
Sungrow SG125HV Manual de usuario
Sungrow
Sungrow SG125HV-30 Manual de usuario
Sungrow
Sungrow SG50KTL-M-20 Manual de usuario
Sungrow
Sungrow SG125CX-P2 Manual de usuario
Sungrow
Sungrow PVS-24MH Manual de usuario
Sungrow
Sungrow SG125HX Manual de usuario
Sungrow
Sungrow SG5KTL-MT Manual de usuario
Sungrow
Sungrow SG250HX-IN Manual de usuario
