Sun Microsystems StorEdge L7 Manual de usuario

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

Sun StorEdge™L7 Decision Tree

The purpose of the Sun StorEdge L7 Decision Tree is to identify a logical sequence of events to

troubleshoot a Sun StorEdge L7 autoloader based upon the error message displayed on the LCD.

Since there are no Field Replaceable Unit (FRU) items available for servicing a StorEdge L7

autoloader , failure to successfully clear the error message after performing the steps outlined in

this decision tree will result in autoloader replacement.

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

Sun StorEdge L7 Decision Tree

1.0 LCD Blank

A blank LCD indicates a hardware problem with the LCD, cabling problems within theStorEdge L7 or power

supply problems.

DP1: Check the green Power LED on the front panel of the StorEdge L7 to see if it is illuminated. Refer to

Sun StorEdge L7 User’s Guide -> Introduction -> Switches and Indicators -> Front Panel for the location of

green Power LED.

R1: Green Power LED is not illuminated.

DP2:Check to see if the autoloader fan is spinning.

R2: Fan is not spinning.

DP3: Check the AC power cord for proper connection.

R3: AC power cord is properly connected.

A3: Press the POWER button on the front panel of the StorEdge L7.

DP4: Check to see if the LCD is still blank.

R4: LCD is still blank.

DP5: Try a different AC power cord.

R5: Second cord works.

A5: Replace the failing power cord.

R5: Second cord does not work.

R5: Replace the autoloader.

R4: LCD is no longer blank.

A4: Continue normal autoloader operation.

R3: AC power cord is not properly connected.

A3: Reseat the AC power cord.

A3: Press the POWER button on the front panel of the StorEdge L7.

R2: Fan is spinning.

A2: Replace the autoloader.

R1: Green Power LED is illuminated.

A1: Replace the autoloader.

Legend:

DP = Decision Point

R= Response

A= Action

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

2.0 SERIAL RCV

This error message indicates the autoloader has encountered an inter-processor communication error.

Troubleshooting should begin with cycling power to the autoloader.

Note: When powering off the autoloader, the POWER button on the front panel of the autoloader must be

pressed and held for 2 seconds.

DP1: Check to see if the error message is still present after cycling autoloader power.

R1: Error message is still present.

A1: Replace the autoloader.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

3.0 CPU RX ERR

This error message indicates the motion CPU is not ready to receive. Troubleshooting should begin with

cycling power to the autoloader.

Note: When powering off the autoloader, the POWER button on the front panel of the autoloadermust be

pressed and held for 2 seconds.

DP1: Check to see if the error message is still present after cycling autoloader power.

R1: Error message is still present.

A1: Replace the autoloader.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

4.0 CPU TX ERR

This error message indicates the motion CPU is not ready to transmit. Troubleshooting should begin with

cycling power to the autoloader.

Note: When powering off the autoloader, the POWER button on the front panel of the autoloader must be

pressed and held for 2 seconds.

DP1: Check to see if the error message is still present after cycling autoloader power.

R1: Error message is still present.

A1: Replace the autoloader.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

5.0 HALT

This error message indicates the motion CPU has been halted by a low ACT line. Troubleshooting should

begin with cycling power to the autoloader.

Note: When powering offthe autoloader, the POWER button on the front panel of the autoloader must be

pressed and held for 2 seconds.

DP1: Check to see if the error message is still present after cycling autoloader power.

R1: Error message is still present.

A1: Replace the autoloader.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

6.0 NVM SELECT

This error message indicates an NVRAM selection failure. Troubleshooting should begin with cycling power

to the autoloader.

Note: When powering off the autoloader, the POWER button on the front panel of the autoloader must be

pressed and held for 2 seconds.

DP1: Check to see if the error message is still present after cycling autoloader power.

R1: Error message is still present.

A1: Replace the autoloader.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

7.0 NVM WRITE

This error message indicates an NVRAM write failure. Troubleshooting should begin with cycling power to

the autoloader.

Note: When powering off the autoloader, the POWER button on the front panel of the autoloader must be

pressed and held for 2 seconds.

DP1: Check to see if the error message is still present after cycling autoloader power.

R1: Error message is still present.

A1: Replace the autoloader.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

8.0 CAM LIMIT

This error message indicates a cam limit has been reached without tripping a sensor. Troubleshooting

should begin with cycling power to the autoloader.

Note: When powering off the autoloader, the POWER button on the front panel of the autoloader must be

pressed and held for 2 seconds.

DP1: Check to see if the error message is still present after cycling autoloader power.

R1: Error message is still present.

A1: Replace the autoloader.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

9.0 JAW SENSOR

This error message indicates a jaw sensor has been tripped. Troubleshooting should begin with cycling

power to the autoloader.

Note: When powering off the autoloader, the POWER button on the front panelof the autoloader must be

pressed and held for 2 seconds.

DP1: Check to see if the error message is still present after cycling autoloader power.

R1: Error message is still present.

A1: Replace the autoloader.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

10.0 SRC EMPTY

This error message indicates the autoloader attempted to get a tape from a selectable storage slot but the

tape is no longer there. A user manually removing a tape from the selected storage slot prior to the

autoloader gettingto the tapecan cause this error. Troubleshooting should begin byconfirming if the tape

was manually removed during the autoloader operation, and if confirmed, manually replacing the tape to

the selected storage slot and retrying the autoloader operation. An obstructed slot sensor (dust, lint, etc.

blocking the slot sensor) can also cause this error, as the autoloader will attempt to get a tape that isn’t

really there. Troubleshooting should continue with confirming the storage slot is empty, and if confirmed,

using compressed air to remove dust/debris from the slot sensor.

DP1: Check to see if the user manually removed the tape during the autoloader operation.

R1: User manually removed the tape from the selected storage slot.

A1: Replace the tape to the selected storage slot.

A1: Retry the autoloader move operation.

DP2: Check to see if the error message is still present.

R2: Error message is still present.

A2: Replace the autoloader.

R2: Error message no longer present.

A2: Continue normal autoloader operation.

R1: User did not manually remove the tape from the selected storage slot.

A1: Power down the autoloader.

A1: Remove all tapes from the autoloader.

A1: Use compressed air to clean all tape slot sensors.

A1: Replace all tapes.

A1: Power up the autoloader and retry the autoloader move operation.

DP2: Check to see if the error message is still present.

R2: Error message is still present.

A2: Replace the autoloader.

R2: Error message no longer present.

A2: Continue normal autoloader operation.

11.0 dEST FULL

This error message indicates the autoloader attempted to place a tape to a selectable storage slot but the

storage slot is now full. A user manually placing a tape to the selected storage slot prior to the autoloader

placing its tape can cause this error. Troubleshooting should begin withconfirming if the tape was manually

placed during the autoloader operation, and if confirmed, manuallyremoving the tape from the storage slot

and retrying the autoloader operation.

DP1: Check to see if the user manually placed a tape during the autoloader operation.

R1: User manually placed a tape to the selected storage slot.

A1: Remove the tape from the selected storage slot.

A1: Retry the autoloader move operation.

DP2: Check to see if the error message is still present.

R2: Error message is still present.

A2: Replace the autoloader.

R2: Error message no longer present.

A2: Continue normal autoloader operation.

R1: User did not manually place a tape to the selected storage slot.

A1: Power down the autoloader.

A1: Remove all tapes from the autoloader.

A1: Use compressed air to clean all tape slot sensors.

A1: Replace all tapes.

A1: Power up the autoloader and retry the autoloader move operation.

DP2: Check to see if the error message is still present.

R2: Error message is still present.

A2: Replace the autoloader.

R2: Error message no longer present.

A2: Continue normal autoloader operation.

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

12.0 REAR TAPE

This error message indicates the autoloader’s rear tape sensor was not tripped during a tape move

operation.The autoloader’s front and rear tape sensorsare used to detect tape location during a tape

move operation and to confirm the tape has cleared the picker path. Troubleshooting should begin with

retrying the move operation.

DP1: Check to see if the error message is still present after retrying the autoloader move operation.

R1: Error message is still present.

A1: Cycle power to the autoloader.

A1: Retry the autoloader move operation.

DP2: Check to see if the error message is still present.

R2: Error message is still present.

A2: Power down the autoloader.

A2: Remove all tapes from the autoloader.

A2: Use compressed air to clean all tape slot sensors.

A2: Replace all tapes.

A2: Power up the autoloader and retry the autoloader move operation.

DP3: Check to see if the error message is still present.

R3: Error message is still present.

A3: Replace the autoloader.

R3: Error message no longer present.

A3: Continue normal autoloader operation.

R2: Error message no longer present.

A2: Continue normal autoloader operation.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

13.0 FRONT TAPE

This error message indicates the autoloader’s front tape sensor was not tripped during a tape move

operation. The autoloaders front and rear tape sensors are used to detect tape location during a tape move

operation and to confirm the tape has cleared the picker path. Troubleshooting should begin with retrying

the move operation.

DP1: Check to see if the error message is still present after retrying the autoloader move operation.

R1: Error message is still present.

A1: Cycle power to the autoloader.

A1: Retry the autoloader move operation.

DP2: Check to see if the error message is still present.

R2: Error message is still present.

A2: Power down the autoloader.

A2: Remove all tapes from the autoloader.

A2: Use compressed air to clean all tape slot sensors.

A2: Replace all tapes.

A2: Power up the autoloader and retry the autoloader move operation.

DP3: Check to see if the error message is still present.

R3: Error message is still present.

A3: Replace the autoloader.

R3: Error message no longer present.

A3: Continue normal autoloader operation.

R2: Error message no longer present.

A2: Continue normal autoloader operation.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

14.0 REAR SLOT

This error message indicates a rear slot sensor was not tripped after a tape move to a rear storage slot.A

defective rear slot sensor can cause this error. Troubleshooting should begin with retrying the move

operation to the same rear slot. An obstructed rear slot sensor (dust, lint, etc. blocking the slot sensor) can

also cause this error. Troubleshooting should continue with using compressed air to remove dust/debris

from the slot sensor.

DP1: Check to see if the error message is still present after retrying the tape move operation.

R1: Error message is still present.

A1: Power down the autoloader.

A1: Remove all tapes from the autoloader.

A1: Use compressed air to clean all tape slot sensors.

A1: Replace all tapes.

A1: Power up the autoloader and retry the autoloader move operation.

DP2: Check to see if the error message is still present.

R2: Error message is still present.

A2: Replace the autoloader.

R2: Error message no longer present.

A2: Continue normal autoloader operation.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

15.0 FRONT SLOT

This error message indicates a front slot sensor was not tripped after a tape move to a front storage slot. A

defective front slot sensor can cause this error. Troubleshooting should begin with retrying the move

operation to the same front slot. An obstructed front slot sensor (dust, lint, etc. blocking the slot sensor)

can also cause this error. Troubleshooting should continue with using compressedair to remove dust/debris

from the slot sensor.

DP1: Check to see if the error message is still present after retrying the tape move operation.

R1: Error message is still present.

A1: Power down the autoloader.

A1: Remove all tapes from the autoloader.

A1: Use compressed air to clean all tape slot sensors.

A1: Replace all tapes.

A1: Power up the autoloader and retry the autoloader move operation.

DP2: Check to see if the error message is still present.

R2: Error message is still present.

A2: Replace the autoloader.

R2: Error message no longer present.

A2: Continue normal autoloader operation.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

16.0 PCKR FULL

This error message indicates the autoloader’s picker contains a tape that needs to be returned toits storage

location. A tape in the picker at power down, followed by a power up, is the most likely cause of this error.

Troubleshooting should beginwith cycling power to the autoloader and ejecting the tape in the picker to its

storage location. For instructions on ejecting a tape from the picker via the front panel, refer to Sun

StorEdge L7 User’s Guide -> Operation and Maintenance -> Autoloader Modes -> Mode 4 –EJECT PCKR.

DP1:Check to see if the error message is still present after cycling autoloader power and retrying the picker

eject operation.

R1: Error message is still present.

A1: Power down the autoloader.

A1: Manually remove the tape from the picker.

A1: Inspect the tape and pickerand remove any debris (tape, labels, etc.)that may be preventing the

tape from ejecting from the picker.

A1: Replace the tape that was removed from the picker.

A1: Power up the autoloader and perform a tape move with the same tape.

DP2: Check to see if an error message is still present after performing a tape move with the same

tape.

R2: Error message still present.

A2: Power down the autoloader and manually remove the tape.

A2: Power up the autoloader and repeat a tape move operation with another tape.

DP3: Check to see if an error message is still present after performing a tape

move with a different tape.

R3: Error message still present.

A3: Replace the autoloader.

R3: Error message no longer present.

A3: Replace the defective tape and continue normal autoloader

operation.

R2: Error message no longer present.

R2: Continue normal autoloader operation.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

17.0 PCKR EMPTY

This error message indicates the autoloader attemptedto perform an EJECT PCKR operation (referenceSun

StorEdge L7 User’s Guide -> Operation and Maintenance -> Autoloader Modes -> Mode 4 –EJECT PCKR)

with no tape present in the picker. The PCKR EMPTY error message will appear on the LCD for

approximately 25 seconds.The error message can be cleared prior to 25 seconds by pressing the MODE

button on the front panel of the autoloader to return the autoloader to LdR REAdY status.

18.0 dRIVE EJCT

This error message indicates the autoloader failed to eject a tape from a drive. Troubleshooting should

begin with retrying the drive eject operation. For instructions on ejecting a tape from a drive via the front

panel, refer to Sun StorEdge L7 User’s Guide-> Operation and Maintenance-> Autoloader Modes -> Mode

1B –EJECT DRV.

DP1: Check to see if the error message is still present after retrying the drive eject operation.

R1: Error message is still present.

A1: Cycle power to the autoloader.

A1: Retry the drive eject operation.

DP2: Check to see if the error message is still present after retrying the drive eject operation.

R2: Error message still present.

A2: Replace the autoloader.

R2: Error message no longer present.

R2: Continue normal autoloader operation.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

19.0 dRIVE LOAd

This error message indicates the autoloader failed to load a tape into a drive. Troubleshooting should begin

with retrying the drive load operation. For instructions on loading a tape to a drive via the front panel, refer

to Sun StorEdge L7 User’s Guide ->Operation and Maintenance -> Autoloader Modes -> Mode 1A–LOAD

DRV.

DP1: Check to see if the error message is still present after retrying the drive load operation.

R1: Error message is still present.

A1: Cycle power to the autoloader.

A1: Retry the drive load operation.

DP2: Check to see if the error message is still present after retrying the drive load operation.

R2: Error message still present.

A2: Replace the autoloader.

R2: Error message no longer present.

R2: Continue normal autoloader operation.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

20.0 dRIVE UNLd

This error message indicates the autoloader failed to eject a tape from a drive due to the drive not being

logically unloaded. Troubleshooting should begin with retrying the driveeject operation. For instructions on

ejecting a tape from a drive via the front panel, refer to Sun StorEdge L7 User’s Guide -> Operation and

Maintenance -> Autoloader Modes -> Mode 1B–EJECT DRV.

DP1: Check to see if the error message is still present after retrying the drive eject operation.

R1: Error message is still present.

A1: Cycle power to the autoloader.

A1: Retry the drive eject operation.

DP2: Check to see if the error message is still present after retrying the drive eject operation.

R2: Error message still present.

A2: Replace the autoloader.

R2: Error message no longer present.

R2: Continue normal autoloader operation.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

21.0 dRIVE HNdL

This error message indicates the autoloader failed to eject a tape from or load a tape to a drive due to a

drive ‘operate handle’ timeout. Troubleshooting should begin with retrying the drive eject or drive load

operation. For instructions on ejecting a tape from a drive via the front panel, refer to Sun StorEdge L7

User’s Guide -> Operation and Maintenance -> Autoloader Modes -> Mode 1B –EJECT DRV. For

instructions on loading a tape to a drive via the front panel, refer to Sun StorEdge L7 User’s Guide ->

Operation and Maintenance -> Autoloader Modes -> Mode 1A –LOAD DRV.

DP1:Check to see if the error message is still present after retrying the drive eject or drive load operation.

R1: Error message is still present.

A1: Cycle power to the autoloader.

A1: Retry the drive eject or drive load operation.

DP2: Check to see if the error message is still present after retrying the drive eject or drive load

operation.

R2: Error message still present.

A2: Replace the autoloader.

R2: Error message no longer present.

R2: Continue normal autoloader operation.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

**ADIC / Sun Confidential** Sun_StorEdge_L7_Decision_Tree_Rev01_

22.0 dRIVE BUSY

This error message indicates the autoloader failed to eject a tape from a drive due to a ‘drive busy’.

Troubleshooting should begin with retrying the drive eject operation after allowing sufficient time for the

drive to finish its current operation. For instructions on ejecting a tape from a drive via the front panel,

refer to Sun StorEdge L7 User’s Guide -> Operation and Maintenance -> Autoloader Modes -> Mode 1B–

EJECT DRV.

DP1: Check to see if the error message is still present after retrying the drive eject operation.

R1: Error message is still present.

A1: Power down the autoloader.

A1: Disconnect the SCSI cable from the rear of the autoloader.

A1: Power up the autoloader.

DP2: Check to see if error message is still present.

R2: Error message still present.

A2: Replace the autoloader.

R2: Error message no longer present.

A2: Retry the drive eject operation.

DP3:Check to see if the drive eject operation was successful.

R3: Drive eject successful.

A3: Power down autoloader.

A3: Reconnect SCSI cable.

A3: Power up autoloader and continue normal autoloader operation.

R3: Drive eject notsuccessful.

A3: Replace the autoloader.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

23.0 dRIVE PGRM

This error message indicates a problem was encountered during a drive firmware upgrade. For specific

instructions on upgrading drive firmware, refer to Sun StorEdge L7 User’s Guide -> Troubleshooting and

Diagnostics -> Using the Diagnostic Menu -> Upgrade Drive Firmware. Troubleshooting should beginwith

verifying the tape used for the drive firmware upgrade is a valid FUP tape and not a data or cleaning tape.

DP1: Check to see if the error message is still present after verifying the tape used for the drive firmware

upgrade is a valid FUP tape and retrying the firmware upgrade process.

R1: Error message is still present.

A1: Contact Technical Support for assistance.

R1: Error message no longer present.

A1: Continue normal autoloader operation.

Otros manuales para StorEdge L7

Otros manuales de Almacenamiento de Sun Microsystems

Sun Microsystems

Sun Microsystems StorEdge N8200 Manual de instalación y operación

Sun Microsystems

Sun Microsystems StorageTek SL500 Manual de usuario

Sun Microsystems

Sun Microsystems SPARCstorage Library Manual de usuario

Sun Microsystems

Sun Microsystems StorEdge 3900 Series Instrucciones de funcionamiento

Sun Microsystems

Sun Microsystems StorEdge T3+ Manual de usuario

Sun Microsystems

Sun Microsystems StorEdge D2 Guía de configuración

Sun Microsystems

Sun Microsystems Sun Enterprise 6500 Manual de usuario

Sun Microsystems

Sun Microsystems SUN-OCC-SMC576 Manual de usuario

Sun Microsystems

Sun Microsystems SPARCstorage Library Manual de usuario

Sun Microsystems

Sun Microsystems 7120 Manual de usuario

Sun Microsystems

Sun Microsystems StorEdge 5310 Manual de usuario

Sun Microsystems

Sun Microsystems Sun Fire B1600 Administration Manual de lista de piezas

Sun Microsystems

Sun Microsystems TIMBERWOLF 9740 Manual

Sun Microsystems

Sun Microsystems StorageTek T9840 Instrucciones de montaje

Sun Microsystems

Sun Microsystems SUN BLADE 150 Manual de usuario

Sun Microsystems

Sun Microsystems StorEdge L1800 Manual de usuario

Sun Microsystems

Sun Microsystems Sun Storage J4200 Guía de instalación

Sun Microsystems

Sun Microsystems StorEdge N8400 Manual de usuario

Sun Microsystems

Sun Microsystems Enterprise Tape Library 7/3500 Guía de inicio rápido

Sun Microsystems

Sun Microsystems StorEdge D2 Instrucciones de uso

Sun Microsystems

Sun Microsystems StorEdge 3900 Series Manual de usuario

Sun Microsystems

Sun Microsystems 2.1 Gbyte 7200 rpm Manual de usuario

Sun Microsystems

Sun Microsystems StorEdge Series Manual de usuario

Sun Microsystems

Sun Microsystems StorEdge N8400 Manual de instalación y operación

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario