studiobricks One Manual de usuario
11
One, OnePlus,
& OneXXL
Assembling
guide
Last update | January 2022
2
For safe usage
please observe
the following
All bricks are referenced therefore should be placed in
certain order during assembly.
We recommend that you use manual screwdriver to
avoid scratches.
Be very careful not to open the door while the cabin is
unnished. If there is no other option than to open the door
during assembling because you install the cabin between
walls, open it very carefully and balance the weight.
IMPORTANT! Please note that no part of the cabin
should touch the building except for the feet. Leave at least
5cm space between the cabin and the wall to avoid vibrations
and assure proper sound isolation properties
Installation, connection and commissioning must be
done by qualied professional (according to IEC60050;
IEV195-04-01) with professional electrotechnical skills.
Inappropriate installation can lead to danger to life and
danger to the life of the users of the installation.
With improper installation you risk heavy material
damage e.g. through re. In case of non properly done
installation, Studiobricks can’t be held liable in case of
damage of persons and material assets. Volt-free dismounting.
The carrier must unload the cabin on flat floor, never
inclined such as an access ramp to garage, for example,
the box could tip over and injure people.
It is suggested to have at least 3 people for the assembling
of this model as pieces are very heavy.
Caution in opening the box on the incorrect side as
parts may fall out.
Make sure there are no children or pets nearby during
the unpacking of the cabin.
During unpacking, remove the highest parts and those
on top of others, rst. Alternate parts on one side and
another to ensure the stability of the packaging. Any heavy
part that moves during unboxing can cause the entire
package to overturn.
Please follow the steps of this model carefully.
It is very important to level the floor well before begin-
ning the assembly. A poorly leveled cabin can jeopardize
the stability of the assembly and makes it challenging to
t the pieces correctly.
Make sure to adjust the feet of the booth well so it
keeps stable during the assembly.
IMPORTANT! The floor and the
ceiling frame come together,
make sure to separate them
before you start assembling.
3
Index
Precautions 2
Starting 4
Delivery 4
Unpacking 4
Parts 5
Tools 6
Organization 6
Diferences between Studiobricks One, 7
One Plus and One XXL
Assembly 8
Platform setup for Studiobricks One XXL
8
Building thestructureforStudiobricks One XXL
9
Platform setup for Studiobricks One/Plus 11
BuildingthestructureforStudiobricksOne/Plus
12
Common steps 14
Finishing 34
Moving your booth 44
4
Before the assembly
1. Starting
1.1 Delivery
Your Studiobricks One booth will arrive in box.
NOTE! If you detect any damages on the box
during delivery please record these damages on
the shipping documents.
In case of damage claim for reimbursement can be
done by the insurance company. Delivery company will
not be responsible for the removal of the empty box
and must be disposed by the receiver.
1.2 Unpacking
Open the box by unscrewing the lid on the marked
side labeled “open this side”.
Caution in opening the box on the incorrect
side as parts may fall out.
After taking all the pieces out please inspect carefully
that everything has arrived in good shape and that all
pieces are complete.
5
Before the assembly
List of parts for Studiobricks One XXL:
Bricks 16
Floor ring (with 8 battens) 1
Silentblocks 10
Central silentblocks 2
Floor carpet pieces 3
Roof ring 1
Cieling brick 1
Rubber parts 16
60cm vertical large battens 12
30 cm vertical short battens (level D) 4
Horizontal batten (A1, B1, C1, D1) 4
Square battens B 16
Square battens C 4
Door 1
Door handle 1
Ventilation kit (optional) 1
Cieling absorber (as part of the roof) 1
Led light 1
Cable port 1
Trim cable port 2
Voltage transformer (USA) 1
Paint pot 1
1.3 Parts
List of parts for Studiobricks One and One Plus:
Bricks 16
Floor (with 8 battens) 1
Silentblocks Studiobricks One/One Plus 5/7
Floor carpet piece 1
Roof ring 1
Cieling brick 1
Rubber parts 16
60cm vertical large battens 12
30 cm vertical short battens (level D) 4
Square battens A 4
Square battens B 12
Square battens C 4
Door 1
Door handle 1
Ventilation kit (optional) 1
Cieling absorber (as part of the roof) 1
Led light 1
Cable port 1
Trim cable port 2
Voltage transformer (USA) 1
Paint pot 1
IMPORTANT!
The floor and the ceiling frame come together, make sure to separate
them before you start assembling.
6
Before the assembly
1 . 4 Tools
To build this booth you will need the following tools:
rubber mallet, snap blade utility knife, screwdriver,
spirit level and stepladder.
1
.5 Organization
Please keep in hand all tools that will be needed
during the assembly. The order of assembly will be the
following:
1) Platform setup
2) Assembly of level A
3) Assembly of level B
4) Roof assembly
5) Electric Connection
6) Interior extras
Please note that each brick is labeled with specic
letter and number.The letters show in what level the
brick is meant to be at. The numbers is the position in
respect to the door. The rst brick from the left side
of the door is number 1.
A
3
2
4
5
1
B
C
D
7
Before the assembly
1.6 Diferences
between
Studiobricks
One, One Plus
and One XXL
Studiobricks One models have the same, therefore the
same assembling instructions, except for some small
diereneces:
1) The Studiobricks One Plus is the same as the
Studiobricks One, but with some 30 cm.
2) The Studiobricks One XXL is the same as the
Studiobricks One Plus, but the floor structure is
dierent to facilitate assembly and transportation:
a) The floor of the XXL model is made up of
perimeter ring and 3 carpeted central pieces.
On the other hand, in Studiobricks One and
Studiobricks One Plus’ floor is single piece
covered with carpet.
b) Studiobricks One XXL doesn’t come with A
battens, only B battens + horizontal batten instead.
We use Studiobricks One Plus booth as the
model for this assembly guide.
A
B
B
A
Studiobricks One and One Plus floor
Studiobricks One XXL floor
8
Assembly
2. Assembly
2.1 Platform
setup for
Studiobricks
One XXL
The Studiobricks One models are equipped with
silentblocks on the bottom of the ring floor piece.
Stack felt piece in each silentblock to
prevent them from staining and denting the floor
over time.
First, put them in the holes underneath the floor level.
Then you need to level the ring floor platform by
adjusting the silentblocks.
Start by adjusting the silentblocks, then balance the
whole ring using spirit level to ensure it is level.
Next adjust the silentblocks so they rest on the
floor. Again, use spirit level to ensure the floor is
completely level.
You need to level the ring floor by adjusting
the silentblocks.
Felt
piece
Silent
blocks
IMPORTANT! The floor and the ceiling
frame come together, make sure
to separate them before you start
assembling.
LEVEL
UP
LEVEL
DOWN
9
2.2 Start
building the
structure for
Studiobricks
One XXL
You will now go on slotting all the panels in
numerical order and clockwise. It´s easier if you
slot in panel A5 bit later.
We advise to tilt the piece bit before placing
it in place. Use this little trick to t the following
bricks for level A.
Please note that you can change the A2 Brick
with the A4 Brick in case you want the wire shaft
and ventilator in the opposite side.
A1 brick:
Start with the A1 brick. Place it on the left side of the
entrance door as indicated by the image. You can now
start building the walls.
A2 brick:
Place brick A2 as seen in the image to the left, tting
it with the A1 brick.
A3 brick:
Place brick A3 as seen in the image to the left, tting
it with the A2 brick.
A1
brick:
A2
brick:
A3
brick:
Assembly
10
Floor carpet panels:
Once you’ve completed level A except for A4 and A5
brick it’s time to place the 3 panels that make up the
floor. Like the wall bricks, the floor panels are made
of sound isolating materials to prevent sound from
scaping downwards.
We will start by placing the 2 panels of the end.
Next, we can place the center panel.
Be careful not to catch your ngers when
putting the central panel on the floor.
A4 brick:
Place brick A4 as seen in the image, tting it with the
A3 brick.
Central
panel:
A4
brick:
Floor
carpet
panels
Assembly
Otros manuales para One
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Manuales populares de Producto de plomería de otras marcas
Weka
Weka 506.2020.00E Instrucciones de funcionamiento
Kohler
Kohler K-6228 Instrucciones de montaje
UBERHAUS DESIGN
UBERHAUS DESIGN 75175017 Manual de usuario
American Standard
American Standard DetectLink 6072121 Manual de usuario
Uponor
Uponor Contec TS Manual de usuario
Pfister
Pfister Selia 49-SL Manual de usuario
