Stratus SAE-C10XE Guía

Model No. SAE-C10XE

Direct drive 2 post Lift

Single point electric release

Lifting Capacity 10,000 lbs

Installation & Operation &

Maintenance Instructions

mportant

Note

1. This equipment can not be installed, operated or repaired without reading instructions.

2. Electricity must be hooked up by certified electrician.

3. Do not use this equipment beyond its rated capacity.


 
TABLE OF CONTENTS 
 
Packing, transport and storage ..................................................................................................................................4 
1 Packing .................................................................................................................................................................4 
2 Transport .............................................................................................................................................................4 
3 Storage..................................................................................................................................................................4 
Technical specifications..............................................................................................................................................5 
1 Equipment plan ...................................................................................................................................................6 
Safety............................................................................................................................................................................8 
1 Important notices ................................................................................................................................................8 
2 Qualified personnel .............................................................................................................................................8 
3 Danger notices .....................................................................................................................................................8 
4 Training................................................................................................................................................................9 
5 Warning signs ......................................................................................................................................................9 
Installation.................................................................................................................................................................10 
1 Tool required .....................................................................................................................................................10 
2 Checking for room suitability ...........................................................................................................................11 
3 Lighting...............................................................................................................................................................11 
4 Floor requirement .............................................................................................................................................11 
5 Site layout...........................................................................................................................................................11 
6 Assembly diagram .............................................................................................................................................12 
7 Assemble columns.............................................................................................................................................12 
8 Installation overhead top beam .......................................................................................................................13 
9 Position columns ...............................................................................................................................................13 
10 Adjust carriage...............................................................................................................................................14 
11 Install cables (2 Cables in total )...................................................................................................................15 
12 Routing the safety release cable ...................................................................................................................15 
13 Installation of power unit..............................................................................................................................16 
14 Make the electrical connection.....................................................................................................................16 
15 Oil filling and bleeding...................................................................................................................................16 
16 Installation of lifting arms and adjustment of arm locks............................................................................17 
Check before start-up................................................................................................................................................18 
1 General checks...................................................................................................................................................18 
2 Mechanical safeties for proper installation.....................................................................................................18 
3 Equalizer cable for proper installation............................................................................................................18 
4 Hydraulic system for proper operation...........................................................................................................18 
5 Check with load..................................................................................................................................................18 
 


 
Operation and use .....................................................................................................................................................19 
1 Controls ..............................................................................................................................................................19 
2 Vehicle positioning ............................................................................................................................................19 
3 Lifting..................................................................................................................................................................20 
4 Standing..............................................................................................................................................................20 
5 Lowering ............................................................................................................................................................20 
Maintenance...............................................................................................................................................................21 
1 Ordinary maintenance ......................................................................................................................................21 
2 Periodic maintenance........................................................................................................................................21 
Troubleshooting ........................................................................................................................................................22 
Parts list .....................................................................................................................................................................23 
1 Main column and parts list ...............................................................................................................................23 
2 Packing list .........................................................................................................................................................26 
Special notes ..........................................................................................................................................................27 
1 Environmental damage .................................................................................................................................27 
2 Dismantling ....................................................................................................................................................27 
3 Disposal ..........................................................................................................................................................27 
4 Noise declaration...........................................................................................................................................27

1. Packing, transport and storage

All packing, lifting, handling, transport and unpacking operations are to be performed exclusively byexpert

personnel with knowledge of the lift and the contents of this manual.

1.1 Packing

The packing of the lift is delivered in following components:

a.1 base unit packed in a steel frame, wrapped up in non-scratch material, including all the accessories.

b.1 power unit packed in a carton box

1.2 Transport

➢See Fig 1, packing can be lifted or moved by lift trucks, cranes or bridge cranes. In case of slinging, a second person

must always take care of the load, in order to avoid dangerous oscillations. During loading and unloading operation,

goods must be handled by vehicles or ships.

➢At the arrival of the goods, verify that all items specified in the delivery notes are included. In case of missing parts,

possible defects or damage due to transport operations.

➢If finding missing parts, possible defects or damage due to transport, one should examine damaged cartons

according to <<Packing List.>> to verify the condition of damaged goods and missing parts, also the person in charge or

the carrier must be immediately informed.

➢The machine is heavy goods! Don’t take manpower load and unload and transporting way into consideration, the

safety of working is important.

➢Furthermore, during loading and unloading operation goods must be handled as shown in the picture. (Fig 1)

Fig 1

1.3 Storage

➢The machine equipment should be stocked in the warehouse, if stocked outside should do the disposal well of

waterproof.

➢Use box truck in the process of transport, use container storage when shipping.

➢The control box should be placed perpendicularly during the transport; and prevent other goods from extrusion.

The temperature for machine storage: -10ºC-- 40ºC

2. Technical specifications

Machine model

SAE-C10XE

Installation method

Symmetric Installation

Asymmetric Installation

Lifting capacity

10,000lbs (4,500kg)

Lifting Height

83.07"（2110MM）

Minimum height

3.94"（100M）

Lifting time

About 50 sec

Voltage

220V

Frequency

60Hz

power

2.2KW

Hydraulic oil

46＃/68＃

Working temperature

46＃/68＃

ambient humidity

30-95%

Machine noise

< 76dB(A)

Equipment weight

1642 bs (745kg)

2.1 Equipment plan

Symmetric Installation

Asymmetric Installation

3. Safety

3.1 Important notices

➢This ultra thin low lift is specially designed for lifting motor vehicles that weighs within its outmost lifting capacity.

Users are not allowed to use it for any other purposes. Otherwise, we, as well as our sales agency, will not bear any

responsibility for accidents or damages of the lift. Make sure to pay careful attention to the label of the lifting capacity

attached on the lift and never try to lift cars with its weight beyond.

➢Read this manual carefully before operating the machine so as to avoid economic loss or personnel casualty

incurred by wrong operation. Without professional advice, users are not permitted to make any modification to the

control unit or whatever mechanical unit.

3.2 Qualified personnel

➢Only these qualified staff, who have been properly trained, can operate the lift.

➢Electrical connection must be done by a competent electrician.

➢People who are not concerned are not allowed in the lifting area.

3.3 Danger notices

➢Do not install the lift on any asphalt surface.

➢Read and understand all safety warnings before operating the lift.

➢The lift, if is not specially designed upon customer’s request, is not fit for outdoor use.

➢Keep hands and feet away from any moving parts. Keep feet clear of the lift when lowering.

➢Only these qualified people, who have been properly trained, can operate the lift.

➢Do not wear unfit clothes such as large clothes with flounces, tires, etc, which could be caught by moving parts of

the lift.

➢To prevent evitable incidents, surrounding areas of the lift must be tidy and with nothing unconcerned.

➢The lift is simply designed to lift the entire body of vehicles, with its maximum weight within the lifting capacity.

➢Always ensure the safety latches are engaged before any attempt to work near or under the vehicle.

➢Make sure to place the lifting pads to the positions as suggested by vehicle makers and when gradually lift the

vehicle to the desired height, operators should be certain that the vehicle will not slant, roll-over or slide in lifting process.

➢Check at any time the parts the lift to ensure the agility of moving parts and the performance of synchronization.

Ensure regular maintenance and if anything abnormal occurs, stop using the lift immediately and contact our dealers for

help.

➢Lower the lift to its lowest position and do remember to cut off the power source when service finishes.

➢Do not modify any parts of the lift without manufacturer’s advice.

➢a. If the lift is going to left used for a long time, users are required to:

➢b. Empty the oil tank;

➢c. Lubricate the moving parts with hydraulic oil.

3.4 Training

➢Only these qualified people, who have been properly trained, can operate the lift. We are quite willing to provide

professional training for the users when necessary.

➢Attention: For environment protection, please dispose the disused oil in a proper way.

3.5 Warning signs

➢All safety warning signs attached on the machine are for the purpose of drawing the user’s attention to safety

operation. The labels must be kept clean and need to be replaced when they are worn-out or have dropped. Read the

explanations of the labels carefully and try to memorize them.

4. Installation

➢

Only skilled technicians, appointed by the manufacturer, or by authorized dealers, must be allowed to carry out

installation. Serious damage to people and to the lift can be caused if installations are made by unskilled personnel

➢

Always refer to the exploded views attached during installation.

4.1 Tool required

Rotary Hammer Drill D.20

Carpenter’s Chalk

Hammer

Screw Sets

Level Bar

Tape Measure (7.5m)

English Spanner (12")

Pliers

Ratchet Spanner With Socket (28#)

Socket Head Wrench (3#, 5#, 8#)

Wrench set

(10#, 13#, 14#, 15#, 17#, 19#, 24#, 27#, 30#)

Lock Wrench

Tabla de contenidos

Otros manuales de Sistema de elevación de Stratus

Stratus

Stratus SAE-UT8000 Guía

Stratus

Stratus MS9000XT Manual de usuario

Stratus

Stratus SAE-P48 Guía

Stratus

Stratus SAE-F10P Guía

Stratus

Stratus SAE-C12XE Guía

Stratus

Stratus SAE-F14X Guía

Stratus

Stratus SAE-UT9000 Guía

Stratus

Stratus SAE-S66M Manual de usuario

Stratus

Stratus SAE-F10S Instrucciones de instalación

Stratus

Stratus SAE-C10P Guía

Stratus

Stratus SAE-C12X Guía

Stratus

Stratus SAE-C14X Guía

Stratus

Stratus SAE-F12X Guía

Stratus

Stratus SAE-P410 Manual de usuario

Stratus

Stratus SAE-C9P Guía

Stratus

Stratus SAE-P166M Guía

Stratus

Stratus SAE-C10C Guía

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario