Storage Canopy ST Container shelter Manual de usuario
1
SHELTER ASSEMBLY
MANUAL
20x40x6.5 ST Container shelter
2
PARTS LIST
Part Code
Description
Qty
L1
Left base plate
9
R1
Rigth base plate
9
1
Three way fitting
2
2
Four way fitting
7
3
Top bent tube
18
4
Sidewall bent tube
18
5
Top roof purling
8
6
Connection purlin
32
7
Lower tensioning tube for roof cover
2 groups
8
Angle seat for roof cover
4
9
Roof cover
1
10
Plastic plug
4
11
Ropes
1 dozen
13
Bolt M8x70
144
14
Butterfly bolt
16
14A
Ratchet strap
18
14B
1.5'' Rachet (With Screws)
18
3
SPECIFICATIONS
Width: 20 ft
Length: 40 ft
Height: 6.5 ft
IMPORTANT: READ MANUAL FIRST
Improper site preparation, assembly and maintenance may invalidate warranty and cause
unnecessary and costly mistakes. If you have any questions, contact your local dealer.
For an easy assembly process, we have identified each individual component with the part
code as indicated in the parts list. Please refer to the part code numbers and drawing to
ensure problem-free assembly.
It is necessary to tighten the roof fabric enough to avoid “hammocks” on the roof; also re-
tighten once or twice again after a few months of use. This is important when assembled
during cold seasons (autumn and winter) because the fabric gets stiff in these weather
conditions. When the weather conditions become warmer, the fabric loosens and needs
to be re-tighten
It is the owner’s responsibility to take off snow immediately, otherwise it will slide off on
its own.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
1. Keep the work area clean. Accidents are more likely in cluttered areas. Do not set
up near snow drifts, in slippery places, in high winds, or wet locations.
2. All children should be kept away from the work area.
3. Don’t overreach. Always keep proper footing and balance.
4. Do not assemble under the influence of alcohol or drugs. Read warning labels on
medication prescriptions to determine if your judgment or reflexes are impaired
while taking them. If there is any doubt, do not assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these
conditions are likely to occur. Remove the cover during hurricanes.
6. Be careful with power and heat sources. Do not keep heat sources near the
tarpaulin. Do not expose to open flame.
7. Be aware of personal safety during assembly and use. Be careful not to pinch your
fingers with clips and tubes when assembling: When using, make sure there is
adequate ventilation for any dangerous fumes.
4
EQUIPMENT AND TOOLS FOR INSTALLATION
1. Measuring tape
2. Alignment string
3. Step ladder
4. Welder
5. Sledgehammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A - BASE PLATES INSTALLATION
Please refer to the Figure 1 to place the base plates.
Figure 1
1. The measure must be taken from center to center of the base plates. Refer to the
diagram above and confirm the place of the base plates. ENSURE THAT THE
FOUNDATIONS ARE SQUARE.
2. All the base plates need to be welded on the Containers.
5
B - FRAME INSTALLATION (Refer to figure 2 for these steps)
Figure 2
1. Connect the Three way fitting (part code 1), the Top bent tube (part code 3) and
the Sidewall bent tube (part code 4) with the Bolts M8x70 (part code 13); these
make the external group of arches. DO NOT install the bolts on the top of the truss
where the fabric will rest.
2. Connect the Four way fitting (part code 2), the Top bent tube (part code 3) and the
Sidewall bent tube (part code 4) with the Bolts M8x70 (part code 13); these make
the internal group of arches. Please NOTE the direction of the bolt. DO NOT install
the bolts on the top of the truss where the fabric will rest.
3. Insert one end of the assembled arch into one base plate and force the other end
of the arch into the opposite base plate. Secure the arches in the base plates using
the bolts.
4. After installing the first two arches, connect the Top roof purlin (part code 5) into
the Three way fitting and the Four way fitting using the Butterfly bolt (part code
14).
5. Then connect the Connection purlins (part code 6) on the arches using the Bolts
M8x70 (part code 13). There are 4 pieces of Connection purlins (part code 6) and
one piece of Top roof purlin (part code 5) between each arch.
6. Then install the third arch into the base plate and connect the purlins. Assemble
the arches one by one until the frame is finished.
6
C - ROOF COVER INSTALLATION
NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A
slight breeze is the most advantageous for cover installation. To take advantage of the
breeze, pull the cover up over the arches with the breeze blowing in the cover like a sail
filled with air.
1. Insert the Lower tensioning tube for roof cover (part code 7) into the pockets on
the end of the roof cover (part code 9). Then put the Plastic plug (part code 10).
Figure 3
2. Put the Roof cover (part code 9) EVENLY, CAREFULLY AND SLOWLY atop the frame.
Adjust the cover so that it is square and evenly centered on the frame.
Figure 4
7
3. On the Roof cover, cut pockets over each ratchet on the base plates, then use the
Ratchet strap (part code 14A) to tie down the Lower tensioning tubes.
Figure 5
4. Weld the Angle seats (part code 8) on each container and use Rope (part code 11)
to knit the cover on the two side arches and tie the Roof cover to the Angle seats.
Figure 6
8
Please, check the detailed installation pictures below:
NOTES:
-DO NOT LEAVE THE ROOF COVER UNATTACHED UNDER ANYCIRCUMSTANCES until
the final assembly and tightening has been completed.
-The process is quite easy, but some tightening adjustments will be necessary to get
a flat, tensioned roof cover. Please adjust the roof cover every month.
-Wrap tape around the gap between the steel after installing.
Tabla de contenidos
Otros manuales de Refugio de Storage Canopy
Storage Canopy
Storage Canopy C4040DTR Manual de usuario
Storage Canopy
Storage Canopy C3340 Manual de usuario
Storage Canopy
Storage Canopy DT Container shelter Manual de usuario
Storage Canopy
Storage Canopy Two Car Garage Shelter Manual de usuario
Storage Canopy
Storage Canopy 33x40x12 Manual de usuario
Storage Canopy
Storage Canopy W33 x L40 x H12 ft Manual de usuario
Storage Canopy
Storage Canopy C4040S Manual de usuario
Storage Canopy
Storage Canopy SHELTER Manual de usuario
Storage Canopy
Storage Canopy C3340 Manual de usuario
Storage Canopy
Storage Canopy FB408021P Manual de usuario
Storage Canopy
Storage Canopy C3340S Manual de usuario
Storage Canopy
Storage Canopy C604015S Manual de usuario
Storage Canopy
Storage Canopy FB408021DP Manual de usuario
Storage Canopy
Storage Canopy C3340DTR Manual de usuario
Storage Canopy
Storage Canopy C4060DTR Manual de usuario
Storage Canopy
Storage Canopy 40x60x15 ST Container shelter Manual de usuario
Storage Canopy
Storage Canopy C2620R Manual de usuario
Storage Canopy
Storage Canopy C2640R Manual de usuario
Storage Canopy
Storage Canopy C4060R Manual de usuario
Storage Canopy
Storage Canopy C4020 Manual de usuario
