Storage Canopy C3340S Manual de usuario

SHELTER

ASSEMBLY MANUAL

Model # W10xL12xH 3.6m

C3340S Container Shelter

SPECIFICATION

Width:10m Length:12m Height:3.6m

IMPORTANT ----READ MANUAL FIRST

Improper site preparation, Assembly and Maintenance may invalidate warranty and cause unnecessary and

costly mistake. If you have any questions contact your local dealer.

For User Friendly assembly we have identified each individual component with the part code as indicated in

the parts list. Please refer to the part code numbers and drawing to ensure problem free assembly.

It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-tighten once or

twice again after a few months of use. This is important when assembly in cold weather (autumn and winter)

because the fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric

“slack” again and need to be re-tighten before next winter.

It’s the owners responsibility to take of snow immediately if not slide off by itself.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in

high winds, or wet location.

Keep children away. All children should be kept away from the work area.

Don’t over reach. Keep proper footing and balance at all times.

Do not assemble in under the influence of alcohol or drugs. Read warning labels on prescriptions to

determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not

assemble.

Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely to occur.

Remove the cover during hurricane.

Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not expose to

open flame.

Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips and tubes

when assembling: when using makes sure there is adequate ventilation for exhaust and other dangerous

fumes.

PartsList

Part Code

Description

Qty

Base Plate

Angle seat

Top bent tube

Middle bent tube

Bottom bent tube

Connection purlin

Support tube

12 groups

Clip

Lower tensioning tube for roof cover

2groups

Roof cover

Bolt M8x80

Bolt M10x90

10A

Bolt M8x60

24 groups

Ropes

60m

∮

32 Plastic Plug for end of tensioning tube

Ratchet strap (for tie down ratchet)

Angle seat

Ratchet

SPECIFICATION

Width: 10m Length: 12m Height: 3.6m

IMPORTANT ---- READ MANUAL FIRST

Improper site preparation, Assembly and Maintenance may invalidate warranty and cause

unnecessary and costly mistake. If you have any questions contact your local dealer.

For User Friendly assembly we have identified each individual component with the part code as

indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem

free assembly.

It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also

re-tighten once or twice again after a few months of use. This is important when assembly in cold

weather (autumn and winter) because the fabric is stiff then and when we got the sun and warm

weather afterwards it will make the fabric “slack” again and need to be re-tighten before next

winter.

It’s the owners responsibility to take of snow immediately if not slide off by itself.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

1.Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in

slippery places, in high winds, or wet location.

2.Keep children away.All children should be kept away from the work area.

3.Don’t over reach. Keep proper footing and balance at all times.

4.Do not assemble in under the influence of alcohol or drugs. Read warning labels on

prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If

there is any doubt, do not assemble.

5.Be aware of possible windy conditions; fasten the bases in concrete if these conditions are

likely to occur. Remove the cover during hurricane.

6.Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not

expose to open flame.

7.Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips

and tubes when assembling: when using makes sure there is adequate ventilation for exhaust and

other dangerous fumes.

EQUIPEMNT AND TOOLS FORINSTALIATION

1. Measuring tape

2. String for alignment

3. Step ladder

4. Welder

5. Sledge hammer

6. Wrench

7. Scissors

INSTALLATION PROCESS

A—BASE INSTALLATION

Please refer to the diagram (Figure 1) to place the base plates.

Figure 1

1. The measurement is from center to center of the tubes. Referring to the above diagram and

confirm the place of the base plates. ENSURE THAT THE FOUNDATIONS IS SQUARE.

2. All the base plates should be welded on the Containers.

B—FRAME INSTALLATION

Please refer to the diagram (Figure 1) to install the Frame.

Figure 2

1.As Figure 2 shown find Top bent tube (part code 1), Middle bent tube (part code2) and bottom

bent tubes (part code3). To connect them by Screw M8x80（part code 9）, which makes one group

of arches. Please NOTE the direction of the screw. DO NOT install the screws on the top of the

truss where the fabric will rest.

2.Life an assembled arch into one base plate and force the other end of the arch into the opposite

base plate.

When finishing installing the first two arches, connect the Connection purlins onto them by using

screw M10x90 （part code 10 ）.There are 5 pieces of Connection purlins (part code 4)

between two groups. Then install the third arch into base plate and connect the purlins. Finally

install the Support tube (part code 5) using Screw M8x60（part code10A）and Clip (part code 6).

By turns the assembly for the frame is finished.

C- INSTRUCTION FOR ROOF COVER

NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A

slight breeze is the most advantageous for cover installation. To take advantage of the breeze,

pull the cover up over the arches with the breeze blowing in the cover like a sail filled with air.

Put the Roof cover (part code 8) EVENLY,CARRFULLR AND SLOWLY on the frame. Adjust the cover

so that it is square and evenly centered on the frame.

Using Ropes (part code 11) to knit the cover on the two side arches, finally tie the Roof cover to the Angle

Tabla de contenidos

Otros manuales de Refugio de Storage Canopy

Storage Canopy

Storage Canopy C4040DTR Manual de usuario

Storage Canopy

Storage Canopy 40x60x15 ST Container shelter Manual de usuario

Storage Canopy

Storage Canopy C6040S Manual de usuario

Storage Canopy

Storage Canopy ST Container shelter Manual de usuario

Storage Canopy

Storage Canopy 33x40x12 Manual de usuario

Storage Canopy

Storage Canopy C2620R Manual de usuario

Storage Canopy

Storage Canopy C3340R Manual de usuario

Storage Canopy

Storage Canopy 26x40x10 Container Shelter Single truss Manual de usuario

Storage Canopy

Storage Canopy C4080S Manual de usuario

Storage Canopy

Storage Canopy C2640R Manual de usuario

Storage Canopy

Storage Canopy C3340DTR Manual de usuario

Storage Canopy

Storage Canopy C3340 Manual de usuario

Storage Canopy

Storage Canopy SHELTER Manual de usuario

Storage Canopy

Storage Canopy C604015S Manual de usuario

Storage Canopy

Storage Canopy FB335017P Manual de usuario

Storage Canopy

Storage Canopy C4060DTR Manual de usuario

Storage Canopy

Storage Canopy C4060R Manual de usuario

Storage Canopy

Storage Canopy C4040R Manual de usuario

Storage Canopy

Storage Canopy Two Car Garage Shelter Manual de usuario

Storage Canopy

Storage Canopy DT Container shelter Manual de usuario

Storage Canopy

Storage Canopy FB408021P Manual de usuario

Storage Canopy

Storage Canopy C4040 Manual de usuario

Storage Canopy

Storage Canopy C4040S Manual de usuario

Storage Canopy

Storage Canopy 40x40x15 Manual de usuario

Manuales populares de Refugio de otras marcas

Tempo Fitness

Tempo Fitness S11 Manual de usuario

Tuindeco

Tuindeco 42.7906 Manual de usuario

No Butts Bin

No Butts Bin SR1605 Manual de usuario

TMG

TMG TMG-DT5040CG Manual de usuario

TMG

TMG TMG-DT3063-PRO Manual de usuario

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Manual de usuario

Kampa

Kampa Poled Shelter 300 Manual de usuario

Harnois

Harnois TA-R Manual de usuario

Shelters4Less

Shelters4Less SR1551 Manual de usuario

TMG

TMG TMG-DT50FW8 Manual de usuario

Vikre Handel AS

Vikre Handel AS JIT-1216 Manual de usuario

VARNA buildings

VARNA buildings C2020H Manual de usuario

Frabill

Frabill ICE HUNTER 195 Manual de usuario

Shelters4Less

Shelters4Less SR1588 Manual de usuario

Sealey

Sealey Power Products GSS150819SD Manual de usuario

Crivit

Crivit 104155 Manual de usuario

No Butts Bin

No Butts Bin SR1558-F Manual de usuario

TMG

TMG TMG-ST3040C Manual de usuario