Storage Canopy C3340 Manual de usuario
SHELTER
ASSEMBLY MANUAL
Model # W10xL12xH 3.6m
C3340 Back wall & frame of Container Shelter
C3340 Back wall & frame
1
SPECIFICATION
Width:10m Length:12m Height:3.6m
IMPORTANT----- READ MANUAL FIRST
Impropersite preparation, Assembly and Maintenance may invalidate warranty and cause unnecessaryand costly
mistake. If you have any questions contact your local dealer.
For User Friendly assembly we have identified each individual component with the part code as indicated in the
parts list. Please refer to the part code numbers and drawing to ensure problem free assembly.
It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-tighten once or
twice again after a few months of use. This is important when assembly in cold weather (autumn and winter)
because the fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric
“slack” again and need to be re-tighten before next winter.
It’s the owners responsibility to take of snow immediately if not slide off by itself.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in
high winds, or wet location.
2. Keep children away. All children should be kept away from the workarea.
3. Don’t over reach. Keep proper footing and balance at all times.
4. Do not assemble in under the influence of alcohol or drugs. Read warning labels on prescriptions to
determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not
assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely to occur.
Remove the cover during hurricane.
6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not expose to open
flame.
7. Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips and tubes
when assembling: when using makes sure there is adequate ventilation for exhaust and other dangerous
fumes.
2
PartsList
Part Code
Description
Qty
1
Base plate with tie down ratchet
2
2
Lateral base plate with tie down ratchet
2
3
Added legs φ76*42cm
4
4
Lower standpipe of back wallφ76*2.49m
4
5
Middle standpipe of back wallφ76*2.49m
2
6
Upper standpipe of back wallφ76*92cm
2
8
Upper standpipe of lateral back wall
φ60*74cm
2
9
Middle Horizontal Tube for End Wall
2
10
Middle Horizontal Tube for End Wall
φ40*1.55m
2
11
Middle Beam for End Wall
1
group
12
Middle Suspending Tube
1
13
Sidewall Support tube
1
14
Lower tensioning tube for roof cover
φ32*1.61m
2
15
Back Cover
1
16
Ropes
1
dozen
17
Bolt M10*60
5
18
Bolt M10*90
34
19
Bolt
φ12*110
6
20
Clip
6
21
Stake Peg
8
22
Two-place angle seat
1
23
Φ60 Clip
1
24
Belay objects
1
3
SPECIFICATION
Width: 10m Length: 12m Height: 3.6m
IMPORTANT ---- READ MANUALFIRST
Improper site preparation, Assembly and Maintenance may invalidate warranty and cause
unnecessary and costly mistake. If you have any questions contact your local dealer.
For User Friendly assembly we have identified each individual component with the part code as
indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem
free assembly.
It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also
re-tighten once or twice again after a few months of use. This is important when assembly in cold
weather (autumn and winter) because the fabric is stiff then and when we got the sun and warm
weather afterwards it will make the fabric “slack” again and need to be re-tighten before next
winter.
It’s the owners responsibility to take of snow immediately if not slide off by itself.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
1.
Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in
slippery places, in high winds, or wet location.
2.
Keep children away.All children should be kept away from the work area.
3.
Don’t over reach. Keep proper footing and balance at all times.
4.
Do not assemble in under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If
there is any doubt, do not assemble.
5.
Be aware of possible windy conditions; fasten the bases in concrete if these conditions are
likely to occur. Remove the cover during hurricane.
6.
Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not
expose to open flame.
7.
Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips
and tubes when assembling: when using makes sure there is adequate ventilation for exhaust and
other dangerous fumes.
4
EQUIPEMNT AND TOOLS FOR INSTALIATION
1. Measuring tape
2. String for alignment
3. Step ladder
4. Welder
5. Sledge hammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A—FRAME INSTALLATION
Please refer to the diagram (Figure 1) to install the Frame.
Figure 1
5
Figure 2
1. The measure is from center to center of the tubes. Referring to the above diagram.
2. As the Figure 1 Shown, assembly the frame for end wall according to above drawing,
No.1 is the Base plate needs to be fixed with stake peg (No.21).
3. No.3 & 4 is the added leg and lower standpipe of back wall, connecting them with (NO.19) boltM8*70.
4. No.8 & 4 is the Upper standpipe of lateral back wall and lower standpipe of back wall, connecting them
with (NO.18) bolt M10*90.
5.The clips (NO.20) is use for connecting the tubes together.
6.Angle seat(No.22) is assembly them together with bent tube,this is use to connect the bent tube and the
main frame, to make it more strong.
7.Assembly the arches one by one, then the frame will be finished like Figure 2.
6
C- INSTRUCTION FOR COVER ATTACHED
Install the Roof Cover
NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A slight
breeze is the most advantageous for cover installation. To take advantage of the breeze, pull the
cover up over the arches with the breeze blowing in the cover like a sail filled with air.
1.Use rope(NO.16) to tie the end cover (No.15) to the end wall.
The process is quite easy. But some tightening adjustments will be necessary to produce a flat. Please adjust the
cover timely.
Figure 3
The process is quite easy. But some tightening adjustments will be necessary to
produce a flat. Please adjust the roof cover timely.
Tabla de contenidos
Otros manuales de Refugio de Storage Canopy
Storage Canopy
Storage Canopy 40x60x15 ST Container shelter Manual de usuario
Storage Canopy
Storage Canopy C4040 Manual de usuario
Storage Canopy
Storage Canopy Two Car Garage Shelter Manual de usuario
Storage Canopy
Storage Canopy C3340R Manual de usuario
Storage Canopy
Storage Canopy 40x40x15 Manual de usuario
Storage Canopy
Storage Canopy FB408021P Manual de usuario
Storage Canopy
Storage Canopy C4040S Manual de usuario
Storage Canopy
Storage Canopy SHELTER Manual de usuario
Storage Canopy
Storage Canopy C4020 Manual de usuario
Storage Canopy
Storage Canopy C604015S Manual de usuario
Storage Canopy
Storage Canopy C2620 Manual de usuario
Storage Canopy
Storage Canopy C4040S Manual de usuario
Storage Canopy
Storage Canopy C2640R Manual de usuario
Storage Canopy
Storage Canopy FB406021P Manual de usuario
Storage Canopy
Storage Canopy C4040R Manual de usuario
Storage Canopy
Storage Canopy FB406021DP Manual de usuario
Storage Canopy
Storage Canopy C4080S Manual de usuario
Storage Canopy
Storage Canopy 26x40x10 Container Shelter Single truss Manual de usuario
Storage Canopy
Storage Canopy C3340DTPR Manual de usuario
Storage Canopy
Storage Canopy 33x40x12 Manual de usuario
