STM REVOLUTION 2.0 Manual de usuario
MATERIALS
ASSEMBLY
POWER
MOTOR
WEIGHT &
DIMENSIONS
HOPPER
THROUGHPUT
DUAL-BLADE SYSTEM
Encased in 100% Food-Grade Material
SAE 304/316, Dent-Resistant Stainless Steel
Handle & Heavy Duty Castor Wheels for Easy Mobility
Designed, Manufactured, & Assembled in the USA
Standard 220V | 17.1 Load Amps
Single Phase | 5-1/2 ft. Cord Length
Requires L6-30 Plug
Seek Certified Electrician for Installation Needs
3HP |UL Listed | Long Life Cycle
Small Footprint
Approx. 220 lbs
30" L x 65" H x 22-1/4" W
Holds 21 Liquid Gallons
(Four 5-Gallon Buckets of Material)
Up to 50 lbs +/- Hourly
Up to 400 lbs +/- Daily
Varies with Different Material Types
Custom-made Stainless Steel Serrated Blades
Proprietary Angle for Optimized Cutting of Material
REVOLUTION 2.0™
USER MANUAL
CHUTE &
CHAMBER
SOFTWARE &
UPGRADES
TOUCH
SCREEN
COMPLIANCE
CLEANING
LIFE CYCLE &
WARRANTY
SAFETY
FEATURES
Chute with Vibrating Agitator (non-stick, food-grade)
Blade Area Chamber (food-grade)
Revolution OS V1.2
Upgradable System Software Included for
Lifetime of the Machine
Manual and Automatic Operation
Ergonomic 3.5" Resistive Touch Control Panel
Low, Med, High Speed | Start/Stop
Auger On/Off Time Delay
Pop-Up Error Messages
Standard Service Data for Clogs or E-Stop Conditions
OSHA Compliant
Sliding Back Door for Easy Access
Quick Release Bolts | Dishwasher Friendly
1-Year Parts and Labor Warranty
Motor 10-Year LIfe Cycle
Machine is Fully Enclosed
2 Quick Access Emergency Stop Buttons
Lock-Out Tag-Out Power Switch
Multiple Automatic Internal Safety Limit Switches
PARTICLE SCREENS Fine Particle Screen (food grade, stainless material)
Coarse Particle Screen (food grade, stainless material)
1
TABLE OF CONTENTS
Components ....................................................... 2
Getting Started ................................................... 4
Best Practices & Tips ......................................... 5
Emergency Procedures ..................................... 6
Quick Start Guide ............................................... 7
Touch Screen Operation ....................................... 8
Powering Down ...................................................... 9
Preventative Maintenance .................................. 10
Troubleshooting ................................................. 15
Terms of Business ................................................ 23
2
5. Auger Motor
7. Chute
Hopper1.
1. Hopper - The area your material is
stored as it feed into your
2. Auger Bearing - Provides smooth
rotation as it feeds material into the throat
3. Belt Drive- provides the momentum
and power that spins the blades.
4. Casters- Swiveling caster wheels for
easy mobility.
5. Auger Motor - Powers the auger
6. E-Stop Button- Turns the machine
off in case of an emergency.
7. Chute- After the grinding process
exits out of the machine here.
2. Auger Bearings
COMPONENTS
6. E-Stop Button
4. Casters
3. Belt Drive
Revolution Grinder Components - bit.ly/revolution-components
FRONT
13. Power/Lockout Button
3
8. Lid
12. Touch Screen Control
9. E-Stop Button
10. Top of Back Door Panel
11. Lower Back Door Panel
8. Lid - Open to introduce material into
the hopper
9. E-Stop Button - Turns the machine off
in case of an emergency.
10. Top of Back Door Panel - Easy access
to your blade chamber and chute
11. Lower Back Door Panel - Contains
your electrical components. DO NOT
access this portion as it will VOID your
warranty.
12. Touch Screen Control - Used for
the operation of machine.
13. Power/Lockout Button - Turns on
the power and locks machine.
COMPONENTS
BACK
4
GETTING STARTED
UNPACKING YOUR MACHINE
Carefully unpack your machine and inspect it to
ensure it has not been damaged during shipping.
Make sure all the correct parts are included and
match your invoice. Please contact us if you have
missing or damaged items.
Revolution Grinder Machine
(1) Screen for 3/16" (4.76mm) particles (pre-installed)
(1) Screen for 5/32" (3.96mm) particles
(1) Set of Dual Stainless Steel Blades (pre-installed)
Extra Screens and Blade Sets Available for Additional Cost
IMPORTANT! Always wear cut-proof gloves when handling anything inside the blade chamber.
INCLUDED ITEMS
3/16th Coarse 5/32nd Extraction
Floater Blade
4 Arm Blade
PARTICLE SCREENS
(coarse screen is pre-installed on your machine)
STAINLESS STEEL DUAL BLADE SYSTEM
(both blades are pre-installed in your machine)
5
BEST PRACTICES & TIPS
Inspect your material prior to grinding
Optimal moisture can range between 7-10%
Lab certified optimal moisture is 8.8%
Do not overfill hopper
The Revolution grinder can
handle up to 10% moisture.
IMPORTANT! Always turn off and unplug machine before cleaning or servicing.
Always start motor on the
highest speed setting speed
Auger on 3-seconds run time and 3-seconds
off time to prevent clogging. If material is too
dry, auger can run for longer, but can remain
at 3-seconds of run time.
If product bends without a snap, it's too moist.
It product snaps and keif falls, it's too dry.
Optimal product will bend, then snap.
Preventative Maintenance on Page 10
6
E-STOP BUTTON
LIMIT SWITCHES
EMERGENCY PROCEDURES
If there is a sudden emergency or need to shut off
the machine quickly, press either of the two E-STOP
buttons.
One is located on top of the plate on the rear side
of the machine. The other is located just to the left
of the touch screen.
"Emergency Stop" will display on the touch screen.
NOTE: the machine will not operate in this mode.
To clear the "Emergency Stop", pull the red E-STOP
near the touch screen ensuring the yellow ring
under the bottom is exposed.
If the "Emergency Stop" message is still displayed
and both E-STOP buttons are not pressed, it is likely
a trigger of the limit safety switch. (refer to page 20)
Press in case of an emergency
There are four safety switches located
in the machine that will display the
emergency stop as well. The screen will
tell you which e-stop or limit switch is
tripped. These switches will prevent
the machine from running if not
depressed properly.
Hopper Lid - Under Handle
Behind the Drop Down Chute - Back Left Corner
Slide Panel Door - Top Right Corner
Components Slide Panel Door - Top Right Corner
LIMIT SWITCH LOCATIONS
IMPORTANT! Do not alter limit switches in any way.
8
TOUCH SCREEN OPERATION
START/STOP
Pressthe START button to start
the operation and STOP to stop
the operation of the grinder.
HIGH: 100% of motor speed (1750RPM)
MEDIUM: 50% of full power (875RPM)
LOW: 10% of full power (175RPM)
The Revolution has three speeds for operation.
High, Medium, and Low, indicated by the largest
to smallest icons on the touch screen:
1.
2.
3.
MOTOR SPEEDS The amp meter is located in the lower right corner.
When in higher amperage, the machine will read that
and delay the auger. This allows for the blade chamber
to clear before introducing more material. If the meter
remains high, you may have a clog that needs clearing.
AMP METER
The Revolution has one auger speed that comes pre-set
into the machine. The auger comes pre-set with ON
times and OFF times. This prevents the clogging of
materials and overfeeding the blade. These times may
be changed, but we do not recommend going below 3
seconds off or more than 15 seconds on. If you wish to
alter this please contact Client Services.
AUGER SPEEDS
Tabla de contenidos
Otros manuales de Equipos industriales de STM
STM
STM ROCKETBOX Guía de instalación
STM
STM RX Series Manual de instrucciones
STM
STM RFA Series Manual de instrucciones
STM
STM MINI-ROCKETBOX PLUS+ Manual de usuario
STM
STM ROCKETBOX Manual de usuario
STM
STM MINI-ROCKETBOX CANNA Manual de usuario
STM
STM ATOMIC CLOSER Manual de usuario
STM
STM ROCKETBOX 2.0 Manual de usuario
STM
STM NGN-8100 Manual de usuario
